Page 1 Renault KANGOO Vehicle user manual...
Page 2 Castrol, exclusive Renault partner Benefit from cutting-edge technology born out of competition to ensure the performance and longevity of your Renault thanks to wide range of engine lubricants developed specially by Renault and Castrol. renault.com Renault recommends...
Page 3 Welcome to your new vehicle This driver’s handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
Page 4 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 5: Table Of Contents
Section 1: Getting to know your vehicle Key, radio frequency remote control: general information, use, deadlocking ....Doors ............... . . Locking, unlocking the doors .
Page 6 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Radio frequency remote Radio frequency remote Radio frequency remote control A control B control C 1 Locking all the opening elements. 1 Locking all the opening elements. 1 Locking all the opening elements. 2 Unlocking all the opening elements.
Page 7 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. For replacement, or if you require an additional remote Interference...
Page 8 RADIO FREQUENCY REMOTE CONTROL, KEY: use (1/2) Locking the doors The doors are locked and unlocked using the remote control unit. Remote control A, B or C It is powered by a battery which must be replaced (refer to the information on Press locking button 1.
Page 9 RADIO FREQUENCY REMOTE CONTROL, KEY: use (2/2) Unlocking the doors Remote control A, B or C Press unlocking button 2. Pressing the button briefly unlocks all the doors. Driver’s responsibility when parking or stopping the vehicle A short press on button 3 locks/unlocks Never leave an animal, child or adult who is not self-sufficient alone in the tailgate and, depending on the vehi- your vehicle, even for a short time.
Page 10 DEADLOCKING To activate deadlocking If fitted to the vehicle, this allows the doors to be locked and prevents them Press button 1 twice in quick succes- from being opened with the interior sion. handles (for example, by breaking the The side indicator lights and hazard window and then trying to open the warning lights flash five times to indi- doors from the inside).
Page 11: Doors
DOORS (1/5) Opening from the outside Lights-on reminder buzzer Child safety Unlock the door and pull handle 1. For A warning beep sounds when the driv- At the rear, to prevent the side door information on unlocking the doors, er’s door is opened to warn you that the from being opened from the inside, refer to the information on the “Key, lights are still on.
Page 12 DOORS (2/5) Recommendations con- cerning the sliding side door The following precautions must be taken when opening and closing the doors or any other open- ing element: – Check that nobody, no animal or object is at risk of being harmed when you perform this manoeu- vre.
Page 13 DOORS (3/5) Rear hinged doors Opening the doors to the maximum position Opening from the outside For each door, pull handle 9 to release Unlock the door and pull handle 8. For the door check strap. Open the door as information on unlocking the doors, far as possible.
Page 14 DOORS (4/5) Rear hinged doors (continued) Opening from the inside Pull lever 10 to open the small door. Driver’s responsibility when parking or stopping the vehicle Closing from the inside Never leave an animal, child or adult who is not self-sufficient alone on First close the small door and then your vehicle, even for a short time.
Page 15 DOORS (5/5) Opening manually from the inside If it is not possible to unlock the tail- gate, it can be unlocked manually from the inside. Insert a pencil or similar object into cavity 14, slide the assembly as shown in the diagram and push the tailgate to open it.
Page 16 CENTRAL DOOR LOCKING, UNLOCKING (1/2) Locking the opening elements without the remote control With the engine and ignition off, the sliding side doors closed and a front door open, press switch 1 for more than five seconds. Make sure you have your key with you before you leave your vehicle.
Page 17 CENTRAL DOOR LOCKING, UNLOCKING (2/2) Manual control The doors may then only be opened from inside the vehicle or with the key Using the key for the front doors. Lock or unlock the driver’s door by in- Sliding side door (fuel filler cap serting the key fully into lock 2, and side) turning the key.
Page 18: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING (RAID) Operating principle When the engine is started, the system automatically locks the doors when the vehicle reaches a speed of approxi- mately 4 mph (7 km/h). Operating faults If you notice an operating fault (auto- matic locking impossible), first check that all doors are correctly locked.
Page 19 FRONT HEADRESTS (1/3) To refit the headrest First, check that the headrest rods are clean and correctly aligned. Pull the tab 2 forwards. Insert the headrest rods in the holes, with the notches facing forwards (tilt the seat backwards if necessary). Guide the headrest down to the desired height.
Page 20 FRONT HEADRESTS (2/3) To remove the headrest Raise it to its highest position. Press button 4 and lift the headrest to release Note: when the headrest is removed, take care not to change the positions of the rods. To refit the headrest If the setting of the rods has been al- tered, pull them fully upwards.
Page 21 FRONT HEADRESTS (3/3) To refit the headrest Press tab 5. Insert the headrest rods in the holes with the notches facing forward, and guide the headrest down to the re- quired height. Headrest C To raise the headrest Pull it upwards to the required height. To lower the headrest Press tab 5 and guide the headrest down to the desired height.
Page 22 REAR HEADRESTS (1/2) Five-seater version Storage position 2 Pull it towards you and lower it com- To raise it pletely. Slide it to the required height. When the headrest is fully lowered, it To lower it is in the storage position: do not use Pull it towards you and slide it to the re- this position when someone is sitting in quired height.
Page 23 REAR HEADRESTS (2/2) Special note for four seat Child’s convertible headrest versions If fitted to the vehicle, the child head- rest and booster cushion can only be This version differs in that it has rear installed on the rear side seats. seatbelts and headrests on the rear side seats only.
Page 24: Headrests/Front Seats
FRONT SEATS (1/3) ð To move forwards or To tilt the seatback Heated seats backwards Depending on the seat, lower or lift With the engine running, activate lever 2 and tilt the seatback until it Depending on the seat, lift bar 1 or switch 5;...
Page 25 FRONT SEATS (2/3) Flat position Repositioning the seat – make sure that there is nothing which will prevent the seat from moving; Depending on the vehicle, the seatback Make sure that nothing prevents the – tilt headrest 5 so as to position it on the passenger side may be folded seat from moving.
Page 26 FRONT SEATS (3/3) To refit the seatbacks Refit the seatbacks and click them back into place. Version with front bench seat Front seats for two For safety reasons, carry Operating faults out any adjustments when The seatbacks can be folded down (in (depending on vehicle) the vehicle is not being one or two sections).
Page 27: Roof Flap
ROOF FLAP (1/2) Note: When driving with the roof flap open, you may hear wind noise. To reduce these, open one of the side win- dows slightly. Driving with the roof flap To open: Transverse bar open may be unpleasant for passengers because –...
Page 28 ROOF FLAP (2/2) To close: – Unlock the control 2, the roof flap au- tomatically opens halfway; – pull the handle 1 and lock the roof flap in the closed position. Before starting, always reposition the transverse bar and ensure it is correctly locked.
Page 29: Swivelling Partition
SWIVELLING PARTITION To rotate the partition – unlock the swivelling section by lift- – Pivot the moving section 90 degrees, ing catch 3; lock it at point 5 and lower catch 3. – Unlock the seat base by moving – reposition the seat base, proceeding Note: before refitting the swivelling handle 1 downwards;...
Page 30: Seat Belts
SEAT BELTS (1/4) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants to adjust their seat belts to ensure comply with the legislation of the par- ticular country you are in.
Page 31 SEAT BELTS (2/4) tened. An audible warning sounds at a low volume for 30 seconds, then at a high volume for 90 seconds. Unfastening Press button 4 and the seat belt will be rewound by the inertia reel. Guide the belt.
Page 32 SEAT BELTS (3/4) Version with front bench seat Five-seater version for two Rear centre belt In normal use conditions, fasten the Unwind the belt slowly and ensure that centre seat belt when no one is seated the buckle 8 locks into catch 9. there.
Page 33 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 34: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/5) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt pretensioners; an accident. – driver and passenger front air- – No operation whatso- bags 1.
Page 35 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/5) driver and passenger front Operation Airbags This system is only operational when the ignition is switched on. They are fitted to the front seats on the In a severe frontal impact, the airbags driver’s side and, depending on the ve- inflate rapidly, cushioning the impact hicle, on the passenger’s side as well.
Page 36 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/5) The following conditions will trigger In a frontal impact with another vehi- In a side impact with another vehicle the pretensioners or airbags. cle of an equivalent or higher category, of an equivalent or higher category, at with an impact area equal to or greater an impact speed equal to or greater...
Page 37 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/5) In the following examples, the pre- In the following examples, the pre- – side impact to the front or rear of the tensioners or the airbags could op- tensioners or airbags might not op- vehicle;...
Page 38 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/5) All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. Warnings concerning the driver’s airbag –...
Page 39: Side Protection Devices
SIDE PROTECTION DEVICES Side airbags (depending on vehicle) This air bag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact.
Page 40: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
Page 41: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. Driver’s responsibility A child is not a miniature adult.
Page 42 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 43 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier Up to 18 kg or 4 years, the child may From 15 kg or 4 years, the child can than that of an adult and its neck is very travel on a forward-facing seat.
Page 44 CHILD SAFETY: choosing a child, baby seat mounting (1/2) The are two ways of attaching child Attachment with the ISOFIX system Do not use the child seat seats: via the seat belt or using the Authorised ISOFIX child seats are ap- if it may unfasten the seat ISOFIX system.
Page 45 CHILD SAFETY: choosing a child, baby seat mounting (2/2) The two rings 1 are located between Depending on the vehicle, pass the the seatback and the seat base, behind strap between wheel arch liner 4 and The ISOFIX anchorage the zip fasteners, and are identified by the underside of upper partition 5.
Page 46: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, if neces- child seats. The diagrams on the fol- sary, the seat may be advanced (so as The laws concerning children travel- lowing pages show you how to attach to leave enough space in the rear seats...
Page 47 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear seat Child’s convertible headrest A carrycot can be installed across the If fitted to the vehicle, the child head- vehicle and will take up at least two rest and booster cushion can only be seats.
Page 48: Child Seat: Attachment By Seat Belt
CHILD SEATS: attachment by seat belt (1/4) Van version with two front seats Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² Seat not suitable for fitting child seats.
Page 49 CHILD SEATS: attachment by seat belt (2/4) Van version with three front seats Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² Seat not suitable for fitting child seats.
Page 50 CHILD SEATS: attachment by seat belt (3/4) Estate version with three rear seats ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² Seat not suitable for fitting child seats. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
Page 51 CHILD SEATS: attachment by seat belt (4/4) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Sport tourer versions Front passenger Rear side Rear centre Weight of the child seat (5) (1) seats...
Page 52 CHILD SEATS: attachment using the ISOFIX system (1/5) Estate version with 3 rear seats ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
Page 53 CHILD SEATS: attachment using the ISOFIX system (2/5) Estate version with 2 rear seats ü Seat which allows an child seat to be fitted. ISOFIX. ± The rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be attached.
Page 54 CHILD SEATS: attachment using the ISOFIX system (3/5) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows a child seat with "Universal/Semi-universal or vehicle-specific" approval to be fitted using the ISOFIX system; check that it can be fitted. i-U = Suitable for "universal"...
Page 55 CHILD SEATS: attachment using the ISOFIX system (4/5) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Rear centre Front Sport tourer versions Seat size Weight of Rear side seat, five-...
Page 56 CHILD SEATS: attachment using the ISOFIX system (5/5) (1) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the child seat.
Page 57 CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3) Deactivating the front To deactivate theairbag : with the ve- hicle stationary and the ignition off, passenger airbag push and turn the lock 1 to the OFF po- Before installing a child seat on the sition.
Page 58: Deactivating/Activating The Front Passenger Airbag
CHILD SAFETY: deactivating, activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (for example, the labels shown above) will remind you of these instructions. DANGER Since operation of the front passenger airbag is not...
Page 59 CHILD SAFETY: deactivating, activating the front passenger air bag (3/3) DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat, NEVER fit a rear-facing child re- straint system in a seat protected by an ACTIVATED front AIRBAG.
Page 60: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1.56...
Page 61 DRIVING POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Stalk for: 9 Windscreen demister outlet. 21 Gear lever. – direction indicator lights, – exterior lights, 10 Location for passenger air bag. 22 Remote control/location for radio, –...
Page 62 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1.58...
Page 63 DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 9 – Horn. 15 Location for radio, navigation – Location for driver’s air bag. system. 2 Side air vent. 10 Instrument panel.
Page 64: Warning Lights
WARNING LIGHTS (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. á Main beam headlight tell-tale Variable power assisted light steering warning light Dipped beam headlight tell- This lights up when the ignition is tale switched on and goes out after a few seconds.
Page 65 WARNING LIGHTS (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ô © Coolant temperature warn- Warning light ing light It comes on when the ignition is If this remains lit while driving accom- switched on, sometimes at the same ®...
Page 66 WARNING LIGHTS (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. É Preheating warning light (on Anti-lock braking warning diesel version) light This should come on when the igni- This lights up when the ignition is tion is switched on.
Page 67 WARNING LIGHTS (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ð Ï Ú Battery charge warning light Cruise control and speed limiter indica- If it comes on when you are tor lights driving, it indicates that the circuit is overcharged or has discharged.
Page 68: Displays And Indicators
DISPLAYS AND INDICATORS (1/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Speedometer 1 Rev counter 2 (graduations x 1000) Overspeed buzzer Depending on the vehicle, a beep sounds for 10 seconds approximately every 40 seconds as long as the ve- hicle is travelling at over 74 mph (120 km/h).
Page 69 DISPLAYS AND INDICATORS (2/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Coolant temperature indicator 4 or A In normal use, the needle should be positioned before zone B. Under “inten- sive”...
Page 70 DISPLAYS AND INDICATORS (3/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. – Display selection Press briefly to move from the total mileage to the trip mileage and vice versa. –...
Page 71: Trip Computer
TRIP COMPUTER: general information (1/2) a) Total mileage recorder and trip mile- age recorder; b) journey parameters: – fuel consumed; – average fuel consumption; – current fuel consumption; – estimated range with remaining fuel; – distance travelled; – average speed. c) distance before service;...
Page 72 TRIP COMPUTER: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
Page 73 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 37360 KM a) Total mileage and trip mileage recorder 7080 KM FUEL USED 26.0 L b) Journey parameters Fuel consumed since the last reset.
Page 74 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected CURRENT Current fuel consumption 8.6 L/100 This value is displayed after a speed of approximately 20 mph (30 km/h) is reached.
Page 75 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected c) Mileage before service Distance remaining until the next service (displayed in kilometres), SERVICE IN then when the service nears, several scenarios are possible: 137.7 KM...
Page 76 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected SPEED LIMITER d) Cruise control/speed limiter programmed speed 70 KM/H (depending on vehicle). Please refer to the information on “Cruise control/speed limiter”...
Page 77 TRIP COMPUTER AND WARNING SYSTEM: information messages Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpretation of messages «...
Page 78 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 79 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.
Page 80: Steering Wheel
STEERING WHEEL Steering wheel height adjustment Pull lever 1 and adjust the steering wheel to the required position; push the lever to lock the steering wheel. Make sure that the steering wheel is correctly locked. Never leave the steering wheel on full lock when the vehicle is station- ary.
Page 81 DOOR MIRRORS (1/2) Heated door mirrors With the engine running, mirror de-icing is activated with the rear screen de-ic- ing/demisting. Folding door mirrors Move button 1 to position D to fold the door mirrors in. To reset them for driv- ing, return to position B.
Page 82 DOOR MIRRORS (2/2) Door mirrors with manual Interior rear view mirror adjustment The interior rear-view mirror is adjust- able. To adjust the door mirror, move switch 2. Rear view mirror with lever 3 When driving at night, to avoid being dazzled by the headlights of the vehicle behind, depress the little lever located behind rear view mirror 3.
Page 83 CLOCK AND EXTERIOR TEMPERATURE (1/2) Press and hold the bottom button to enter the minute setting mode. When only the minutes flash, press the top button to scroll through them. Confirm by pressing and holding the bottom button on stalk 3. With the ignition on, the time and, de- Setting clock B pending on the vehicle, exterior tem-...
Page 84 CLOCK AND EXTERIOR TEMPERATURE (2/2) Exterior temperature If the vehicle is suitably equipped, when the exterior temperature is between -3°C and +3°C, the °C characters flash (risk of black ice on the road). Resetting the clock C Vehicles fitted with touch-screen multimedia, navigation aid systems, telephones, etc.
Page 85: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS é Horn Hazard warning lights There is an intermediate position in which the switch may be held when Press one of points 2. Pressing switch 3 illuminates changing lanes. all four direction indicators and the You can also briefly place stalk 1 in the side-mounted indicator lights simul- Direction indicators intermediate position, causing the indi-...
Page 86: External Lighting And Signals
EXTERNAL LIGHTING AND SIGNALS (1/3) Dipped beam Main beam headlights á headlights With stalk 1 in dipped beam headlights Manual operation position, move the stalk towards you. Turn the end of stalk 1 until the symbol The indicator light on the instrument is opposite mark 2.
Page 87 EXTERNAL LIGHTING AND SIGNALS (2/3) “See-me-home lighting” function (depending on vehicle) This function (useful, for example, when opening a gate, garage, etc.) enables you to switch the dipped headlights on momentarily. With the ignition off and the headlights off, pull stalk 1 towards you: the dipped beam headlights come on for approxi- mately sixty seconds.
Page 88 EXTERNAL LIGHTING AND SIGNALS (3/3) Rear fog light Lights-on reminder buzzer  The front fog lights and the A warning beep sounds when the dri- side lights or dipped beam headlights ver’s door is opened to warn you that must be on. the lights are still on.
Page 89: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) 50 m 100 m Control knob 1 is used to adjust the A Incorrect setting: the lights are set height of the headlight beams accord- too high and could dazzle other ing to the load. drivers. Turn the control knob downwards to lower the beam.
Page 90 HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a left- hand drive vehicle (or vice versa), you must adjust your lights tempo- rarily during your stay. Temporary adjustment Open the bonnet and identify the mark- ing B next to one of the front headlight projectors.
Page 91 FRONT WINDSCREEN WASHER, WIPER (1/2) Automatic wiper function (depending on vehicle) With the engine running, move stalk 1. A Park B Automatic wiper function When this position is selected, the system detects the presence of water on the windscreen and trig- gers wiping at a suitable wiping speed.
Page 92 FRONT WINDSCREEN WASHER, WIPER (2/2) Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: – it must remain clean: clean the blade and the screen regularly with soapy water; – do not use it when the screen is dry;...
Page 93 REAR WINDSCREEN WASHER, WIPER Rear screen wash/wipe (depending on vehicle) Turn the end of stalk 1 to position the symbol opposite mark 2. Efficiency of a wiper blade When the stalk is released, it returns to Check the condition of the wiper the rear screen wiper position.
Page 94: Fuel Tank
FUEL TANK (1/3) Fuel grade engine must Use a high-grade fuel that complies switched off for refuelling with the legislation in force in each (and not just on standby country. It must conform to the specifi- for vehicles equipped with cations given on label A inside the fuel the Stop and Start) function: it is es- filler flap.
Page 95 FUEL TANK (2/3) Filling with fuel Petrol versions Petrol versions It is essential to use unleaded petrol. Using leaded petrol will damage the With the ignition off, insert the nozzle The octane rating (RON) should match antipollution system and may lead to a so that the valve opens and then fully the information shown on the label A loss of warranty.
Page 96 FUEL TANK (3/3) Repriming the fuel circuit Vehicles without a manual priming bulb After a breakdown caused by com- – Put the ignition key in “On” position M pletely running out of fuel, the system (please see the information on the must be reprimed before the engine is “Ignition switch”...
Page 97: Reagent Tank
REAGENT TANK (1/5) Please ensure that you comply with the legislation of your country. It is important to remember that failure to respect regulations in force could To fill up with reagent, the engine lead to legal action being taken against must be stopped (not just on the vehicle owner.
Page 98 REAGENT TANK (2/5) Filling (continued) The tank can be filled at the pump. With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be suffi-...
Page 99 REAGENT TANK (3/5) Precautions for use In extreme cold weather conditions In frosty weather conditions, the re- When filling: agent tank should be refilled when – handle the reagent with care. They  can damage clothes, shoes, body- indicator and the message work components etc.;...
Page 100 REAGENT TANK (4/5) Maintenance/Range The information displayed on the instrument panel may be accompanied by a beep. Indicator Message What to do? lights – “AdBlue Level Correct” – When the message is displayed when the ignition is switched on, you have less than 1,488 miles (2,400 km) range. –...
Page 101 REAGENT TANK (5/5) System fault The information displayed on the instrument panel may be accompanied by a beep. Indicator lights Message Readings “Check anti-pollution system” Indicates a fault in the system. Contact your approved  “AdBlue quality to check” © dealer as soon as possible.
Page 102 1.98...
Page 103 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Ignition switch .
Page 104: Running In
RUNNING IN/IGNITION SWITCH Running in Ignition on position M The ignition is switched on: Petrol version – petrol version: you can start the ve- hicle; For the first 600 miles (1,000 km) do not exceed 54 mph (90 km/h) in the –...
Page 105: Starting, Stopping The Engine
STARTING, STOPPING THE ENGINE É Stopping the engine Diesel versions With the engine idling, turn the key to – Turn the ignition key to the the “Stop” position St. “Ignition on” position M, and hold this position until the engine pre- heating light goes off;...
Page 106 FUNCTION STOP AND START (1/4) This system enables a reduced fuel  consumption and lower greenhouse The warning light on the instru- gas emissions. ment panel is lit when the engine is on The system is activated automati- standby. The vehicle equipment re- cally when the vehicle is started.
Page 107 FUNCTION STOP AND START (2/4) Preventing the engine from Special note: depending on the vehi- cle, if you switch off the ignition when standing by the engine is on standby, the warning Ä In certain situations, such as negotiat- light is displayed for a few sec- ing a crossroads for instance, it is pos- onds on the instrument panel.
Page 108 FUNCTION STOP AND START (3/4) Conditions preventing the Special case – the gradient is too steep for vehicles fitted with an automatic gearbox; standby of the engine With the engine on standby (traffic – the “Clear View” function is activated jam, traffic lights, etc.), if you get out of Certain conditions prevent the system (please see “Automatic climate con-...
Page 109 FUNCTION STOP AND START (4/4) Special feature of the automatic The system is automatically reacti- engine re-start vated each time the vehicle is started (see “Starting, stopping the engine” in Under certain conditions, the engine Section 2). can restart on its own in order to guar- antee your safety and comfort.
Page 110 GEAR LEVER Selecting reverse gear (vehicle stationary) Vehicles with manual gearbox: follow the grid drawn on knob 1, and depend- ing on the vehicle, lift ring against the An impact to the under- gear lever knob to select reverse. side of the vehicle while manoeuvring (e.g.: strik- Vehicle with automatic gearbox: refer ing a post, raised kerb or...
Page 111: Handbrake/Power-Assisted Steering
HANDBRAKE/POWER-ASSISTED STEERING Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
Page 112: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.
Page 113: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed However, if the engine does not start after a few seconds and several at- Diesel engines are fitted with an injec- tempts, refer to the information on the tion pump with an electronic regulator “Fuel tank”...
Page 114: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/4) Gear change indicator 2 Fuel consumption is accredited in ac- cordance with a standard regulatory Depending on the vehicle, to obtain op- method. Identical for all manufactu- timum consumption levels, a warning rers, this enables vehicles to be com- light on the instrument panel lets you pared with one another.
Page 115 DRIVING ADVICE, ECO-DRIVING (2/4) While driving, it is possible to exit the ECO mode temporarily in order to im- prove engine performance. To do this, press the accelerator pedal firmly and fully. ECO mode is reactivated when you take pressure off the accelerator pedal. Disabling the function Press switch 4.
Page 116 DRIVING ADVICE, ECO-DRIVING (3/4) – Avoid sudden acceleration. – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- vance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level.
Page 117 DRIVING ADVICE, ECO-DRIVING (4/4) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 118: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that failure to end of their service life, which entered respect antipollution regulations could The exhaust gas monitoring system will into force in 2015.
Page 119: Environment
ENVIRONMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Your vehicle has been designed to emit its entire service life: during production, centres to ensure that it is recycled.
Page 120: Tyre Pressure Loss Warning
TYRE PRESSURE LOSS WARNING (1/9) System identification If fitted on the vehicle, this system warns the driver of pressure loss in one There are two tyre pressure loss warn- or several tyres. ing systems: – System A: can be seen on the label A in the vehicle.
Page 121 TYRE PRESSURE LOSS WARNING (2/9) Operating conditions – driving with snow chains; – fitting a single new tyre; The system should be reset with an – use of tyres not approved by the net- inflation pressure equal to that given work.
Page 122 TYRE PRESSURE LOSS WARNING (3/9) SYSTEM A (cntd.) – repeatedly press the button 3 to Resetting the standard level for the select the “SEt tP” function on the tyre pressures display 2; This should be done: – press and hold (around 3 seconds) –...
Page 123 TYRE PRESSURE LOSS WARNING (4/9) SYSTEM A (cntd.) RECALIBRATE SET TPW Check TPW   Display The warning light flashes for se- The warning light flashes for se- veral seconds, then stays on and, de- veral seconds, then stays on and, de- The display 2 on the instrument panel pending on the vehicle, together with pending on the vehicle, together with...
Page 124 TYRE PRESSURE LOSS WARNING (5/9) SYSTEM A (cntd.) Replacing wheels/tyres Tyre repair product and inflation kit Only use equipment approved by the Only use equipment approved by the Readjustment of tyre pressures brand network, or the system risks brand network, or the system risks The tyre pressures must be adjusted being activated late or not operating being activated late or not operating...
Page 125 TYRE PRESSURE LOSS WARNING (6/9) Resetting the standard level for the tyre pressures This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended);...
Page 126 TYRE PRESSURE LOSS WARNING (7/9) The display of the message “TP ACQUISTION LAUNCHED” for around five seconds indicates that the reset request for the tyre pres- sure reference value has been taken into account. – repeatedly press the button 3 to select the “SEt PP”...
Page 127 TYRE PRESSURE LOSS WARNING (8/9) SYSTEM B (cntd.) Puncture Check Tyre Pressure Sensors   Display The warning light stays on to- The warning light flashes for gether with a beep and, depending several seconds, then stays on and, The display 2 on the instrument panel on the vehicle, the message “TYRE depending on the vehicle, together informs you of any tyre pressure faults...
Page 128 TYRE PRESSURE LOSS WARNING (9/9) SYSTEM B (cntd.) Replacing wheels/tyres Tyre repair product and inflation kit This system requires specific equip- Because the valves are specially desi- Readjustment of tyre pressures ment (wheels, tyres, hubcaps, etc.). gned, only use equipment approved by The tyre pressures must be adjusted Please see the information on “Tyres”...
Page 129 DRIVING CORRECTION DEVICES AND AIDS (1/5) ABS (anti-lock braking Depending on the vehicle, this is com- Operating faults: posed of: system) – If the warning light on the in- – the (anti-lock braking Under heavy braking, the ABS prevents strument panel comes on while driv- system);...
Page 130 DRIVING CORRECTION DEVICES AND AIDS (2/5) Electronic stability program Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operating and traction control ESC in the case of pronounced under- fault the message “WARNING: Check ©...
Page 131 DRIVING CORRECTION DEVICES AND AIDS (3/5) The traction control system offers ad- Hazard warning lights switching on ditional safety. It is recommended that Depending on the vehicle, these may you do not drive with the function disa- light up in the event of sudden decel- bled.
Page 132 DRIVING CORRECTION DEVICES AND AIDS (4/5) Grip control “Soft ground” mode Press switch 1: the indicator light If fitted on the vehicle, grip control  makes it easier to control the vehicle on on the instrument panel comes low grip surfaces (soft ground, etc.). on accompanied by the message “VARIABLE HIGHWAY MODE”.
Page 133 DRIVING CORRECTION DEVICES AND AIDS (5/5) Hill start assistance The hill start assistance This function assists the driver when system cannot completely starting on hills. It prevents the vehicle prevent the vehicle from from rolling backwards, depending on rolling backwards in all sit- the slope, by automatically applying the uations (extremely steep gradients brakes when the driver lifts his/her foot...
Page 134: Speed Limiter
SPEED LIMITER (1/3) Controls Switching on The speed limiter function helps you stay within the driving speed limit that  1 Main “On/Off” switch. Press the side switch 1 . Warning you choose, known as the limit speed.  light comes on, lit orange, and the 2 Limit speed activation, storage and “SPEED LIMITER”...
Page 135 SPEED LIMITER (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any moment. To do this: press the accelerator pedal firmly and fully –...
Page 136 SPEED LIMITER (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 5 (R). Putting the function on Switching off the function standby The speed limiter function is interrupted when you press switch 1. In this case, The speed limiter function is suspended the speed is no longer stored.
Page 137: Cruise Control
CRUISE CONTROL (1/4) This function is an addi- tional driving aid. The func- tion does not take the place of the driver. Therefore, it can under no circum- Controls The cruise control function helps you to stances replace the driver’s respon- maintain your driving speed at a speed sibility to respect speed limits and to 1 Main “On/Off”...
Page 138 CRUISE CONTROL (2/4) Switching on Activating cruise control Driving  At a steady speed (above 18 mph Once a cruising speed is memorised Press switch 1 on the side showing (30 km/h approximately)) press switch 2 and the cruise control function is active, Indicator light 6 comes on, lit green, and or (+): the function is activated and the you may lift your foot off the accelera-...
Page 139 CRUISE CONTROL (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 140 CRUISE CONTROL (4/4) Recalling the cruising speed If a speed has been stored, it is possi- ble to recall it by pressing button 5 (R), on condition that you are driving faster than 20 mph (30 km/h) and that you are sure that the road conditions are suit- able (traffic, road surface condition, weather conditions, etc.).
Page 141: Parking Distance Control
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi- metres from the obstacle.
Page 142 PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the Operating faults system When the system detects an operating fault, a beep sounds for about 3 sec- You can deactivate the system perma- onds as a warning. Consult an ap- nently by pressing and holding switch 2. proved dealer The warning light built into the switch remains lit constantly.
Page 143: Reversing Camera
REVERSING CAMERA (1/2) Operation Note: make sure that the reversing NB: Depending on the vehicle, you can camera is not obscured (by dirt, mud, adjust certain settings from the multi- Moving into reverse gear, the camera 1 snow, condensation, etc.). media display 3.
Page 144 REVERSING CAMERA (2/2) This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately.
Page 145: Automatic Gearbox
AUTOMATIC GEARBOX (1/3) Note: depending on the vehicle, when the selector lever 1 is in a position other than P, display 3 of the gear selected flashes. Starting is impossible. Move the lever 1 to position P, switch on the ignition.
Page 146 AUTOMATIC GEARBOX (2/3) Driving in automatic mode Driving in manual mode With the selector lever 1 in position D, Move lever 1 to position D. move the lever to the left. Shifting the In most traffic conditions, you will not lever repeatedly allows you to change have to touch the gear selector lever gears manually:...
Page 147 AUTOMATIC GEARBOX (3/3) Operating faults Special circumstances Parking the vehicle When the vehicle is stopped, move the – When driving, if the “WARNING: – If the bends and road surface do lever to position P while keeping your Check Gearbox” message and the not allow you to stay in automatic ©...
Page 148 2.46...
Page 149 Section 3: Your comfort Air vents: air outlets ............. . Heating, air conditioning .
Page 150: Air Vents: Air Outlets
AIR VENTS: air outlets (1/2) 1 Demister outlets, side windows. 4 Centre air vents. 2 Side air vents. 5 Control panel. 3 Demisting outlets for the windscreen. 6 Footwell air vents.
Page 151 AIR VENTS: air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Centre air vents Side air vents Settings Settings Air flow: Air flow: Move control knob 7 (beyond the point Move control knob 10 (beyond the point of resistance).
Page 152: Heating, Air Conditioning
HEATING, AIR CONDITIONING (1/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light illuminated) or off (indicator light extinguished) using button 6. The air conditioning or air recirculation can be used to lower the temperature inside the passenger compartment.
Page 153 HEATING, AIR CONDITIONING (2/3) ó The air flow is directed mainly towards the footwells. The air flow is directed to all air vents and the footwells. The air flow is directed mainly to the dashboard vents. The last position is the recommended setting to attain the best comfort level in hot weather.
Page 154 HEATING, AIR CONDITIONING (3/3) Adjusting the ventilation speed Normal use Turn control 3 to one of the four posi- tions B, C, D or E to start the ventilation system and adjust the power. Select position B to set the ventilation to the minimum or select position E to set the ventilation to the maximum.
Page 155: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL (1/8) Controls 8 and 10 - Adjusting the ventilation speed. (depending on vehicle) 11 - Heated rear screen and heated 1 - Clear View button to demist and door mirror de-icing. de ice the windows. 12 - Air recirculation control. 2 - Switching off air conditioning.
Page 156 AUTOMATIC CLIMATE CONTROL (2/8) Only the temperature and the AUTO symbol are displayed Functions managed in automatic mode are not displayed. – press button 6 to increase the tem- perature; – press button 3 to decrease the tem- perature. Note: The maximum and minimum settings of 15°C and 27°C allow the system to produce a minimum or maxi- mum temperature, whatever the am-...
Page 157 AUTOMATIC CLIMATE CONTROL (3/8) Adjusting automatic mode The system normally operates in auto- matic mode but you can alter the stan- dard settings used by the system (air distribution, etc.). These options are ex- plained on the following pages. The displayed temperature values show a comfort level.
Page 158 AUTOMATIC CLIMATE CONTROL (4/8) ô The air flow is directed mainly to the dashboard air vents. This position allows the passenger compartment to be heated or cooled more quickly. ö The air flow is directed to all the windscreen demisting vents and the passenger footwells.
Page 159 AUTOMATIC CLIMATE CONTROL (5/8) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. Automatic mode is switched off by pres- sing buttons 8 and 10. These buttons allow you to increase or decrease ventilation speed.
Page 160 AUTOMATIC CLIMATE CONTROL (6/8) Rear screen de-icing/ To exit this function, press button 11 again. Demisting automatically stops demisting by default. Press button 11. This function allows rapid electric de- misting of the rear screen and, depen- ding on the vehicle, electric de-icing of the door mirrors.
Page 161 AUTOMATIC CLIMATE CONTROL (7/8) Note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compart- ment), press button 10. To exit this function, press: – button 1 again; – or button 5 (the AUTO indicator light on the display will light up).
Page 162 AUTOMATIC CLIMATE CONTROL (8/8) Air recirculation Prolonged use of the air recirculation mode may cause the windows to mist Pressing button 12 activates air recir- up or lead to odours, as the air is not culation (the symbol lights up on the renewed.
Page 163 AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations (air conditioning off, You will normally notice an increase in As a general rule, contact your ap- air recirculation activated, ventilation fuel consumption (especially in town) proved dealer in the event of an oper- speed at zero or low etc.), you may when the air conditioning is operating.
Page 164 AIR CONDITIONING: information and operating instructions (2/2) Ñ Type of refrigerant fluid  Type of oil in the air condi- tioning circuit  Inflammable product  Consult the driver’s hand- book  Maintenance Quantity of refrigerant fluid present in the ve- x.xxx kg hicle.
Page 165: Interior Lighting
INTERIOR LIGHTING (1/2) Courtesy lights Map reading lights Luggage compartment light A (depending on vehicle) (depending on vehicle) Switches 1 or 3 provide: Tilt the switch 3 for permanent lighting. Tilt the switch 4 for permanent lighting. – permanent lighting; In the front passenger seat, press –...
Page 166 INTERIOR LIGHTING (2/2) Special features Depending on the vehicle, remote un- locking of the doors triggers timed light- ing of the passenger compartment. If one of the front or rear doors is opened, the period for which the light is switched on will start again.
Page 167: Sun Visor/Mirrors
SUN VISOR/MIRRORS Front sun visor Courtesy mirror 2 Child minder mirror 3 (passenger side) Lower sun visor 1. The child minder mirror allows you to keep an eye on your child in the back If the sun visor is fitted with a courtesy The clip can be used to hold motorway mirror, it has a cover.
Page 168: Electric Windows
ELECTRIC WINDOWS (1/3) Electric windows From the front passenger seat From the rear seats Press switch 6. With the doors closed, press switch 7. With the ignition on: – press the switch for the window concerned to lower it to the desired Safety of rear occupants height;...
Page 169 ELECTRIC WINDOWS (2/3) Impossible to operate the one-touch electric window The one-touch electric window is equipped with heat protection: if you press the switch for the window more than sixteen consecutive times it goes into protection mode (locking the window). You can: –...
Page 170 ELECTRIC WINDOWS (3/3) Manual window winders Half-opening window Turn handle 8. To half-open the window, turn handle 9 in the direction of the arrow then lock it by pushing the handle. When closing it, check that it is properly locked. Avoid resting any objects against a half-open window: there is a risk that the electric window could be...
Page 171: Ashtray/Cigar Lighter/Accessories Sockets
ASHTRAYS, CIGAR LIGHTER, ACCESSORIES SOCKETS Removable ashtray 1 Cigar lighter 2 Accessories sockets This is a removable ashtray which can With the ignition on, press it in. It will You may use the cigar lighter recess 2 be placed in the cup holders 3. spring back with a click when it is ready.
Page 172 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/5) Glovebox Dashboard storage compartment 2 To open the glove box, lift catch 1. Centre console storage compartment 3 To open, lift cover 4. It will store a 1.5 litre bottle. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged.
Page 173 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/5) Front door storage Storage compartment 8 To replace the seat, proceed in reverse: – lift up the bench seat cushion A so compartments 5 under front passenger seat as to put the rear part of the cush- (for vehicles fitted with front bench seat ion 7 under the seatback;...
Page 174 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/5) Clip 9 Front upper cab storage Central upper storage compartment 10 compartments 12 This can be used for storing motorway tickets, cards, etc. Do not use it for getting into or out of the To open the storage compartments, pull vehicle and do not hang from it.
Page 175 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/5) Sliding side door storage Trays on the front seat 15 Front seat storage pockets 16 compartments 14 Permitted weight: 5 kg, evenly distrib- uted. 3.27...
Page 176 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (5/5) Storage compartment 18 in Clothes hook 19 the front armrest Depending on the vehicle, a hook may (for vehicles fitted with front bench seat be located on the partition behind the for two) front passenger seat.
Page 177: Rear Bench Seat
REAR BENCH SEAT: functions (1/2) For safety reasons, carry out any adjustments when the vehicle is not being driven. When moving the rear bench seat, make sure that the bench seat anchor- age points are clean (they should be free from grit, cloths etc.). To fold down the seatback To raise the seatback Before moving the bench seat, make...
Page 178 REAR BENCH SEAT: functions (2/2) Use restriction Special note for four seat versions It is forbidden to drive with a seatback or a front seat folded down when there This version differs in that it has rear is a passenger occupying a rear seat. seatbelts and headrests on the rear side seats only.
Page 179: Transporting Objects In The Luggage Compartment, Towing
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT, TOWING (1/2) Always position the objects trans- ported so that the largest surface is against: – the rear bench seatbacks, for normal loads; – the front seats for maximum loads. Always position the heav- iest items directly on the floor.
Page 180 TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT, TOWING (2/2) A = 781 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Any towing device must not ob- Section 6. struct any lighting component or the number plate when not in use.
Page 181: Luggage Cover
LUGGAGE COVER The luggage compartment cover is – The storage position C (depending made up of two rigid sections. on the vehicle). There are three possible positions: To store the luggage compartment cover, position it in the runner against – top position A; the rear bench seatback.
Page 182: Luggage Net
LUGGAGE NET The luggage net Positioning the net 2 (depending on vehicle) – Upper section: insert the tabs at the ends of the net in hooks 1; This is located in the luggage compart- ment. – lower section: engage belts 3 in lashing rings 4 on the floor.
Page 183: Roof Bars
ROOF BARS (1/2) To place the bars in the transverse position – Unclip levers 1. – Lift the bars to allow them to be piv- oted (figure A). – Lock the bars in the transverse posi- tion (figure B). – Check that they are correctly locked. It is strictly forbidden to place the roof bars in the transverse position Maximum weight on each roof bar:...
Page 184 ROOF BARS (2/2) To slide the bar Roof bar 2 can be slid to move it closer to or further from the other bar (figure C). There are two positions: centre or rear. With the bar unlocked, pull it towards the front or the rear of the vehicle to slide it in rail 3.
Page 185: Multimedia Equipment
MULTIMEDIA EQUIPMENT The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Multimedia touchscreen; 2 multimedia sockets; 3 radio; 4 steering column control. Refer to the equipment instructions for information on how to operate this equipment. 3.37...
Page 186 3.38...
Page 187 Section 4: Maintenance Bonnet ............... . Engine oil level: .
Page 188: Bonnet
BONNET (1/2) Please note when work- ing close to the engine that Unlocking the bonnet catch To open the bonnet, pull the handle 1. it may be hot. In addition, the engine cooling fan may To open, push tab 2 to the left as you ...
Page 189 BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. Ensure that the bonnet is properly locked.
Page 190 ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact an approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
Page 191: Engine Oil Level
ENGINE OIL LEVEL: general information (2/2) Adding engine oil Use a funnel or protect the filling neck area to avoid engine oil escaping onto a hot part of the engine compartment or a sensitive part (e.g. electrical components). Fire hazard. Before performing any action in the engine com- partment, the ignition must...
Page 192: Topping Up, Filling, Draining
ENGINE OIL LEVEL: topping up, filling, oil change (1/2) Topping up/filling – Unscrew the cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the “MINI” and the ground and the engine should be cold “MAXI”...
Page 193 ENGINE OIL LEVEL: topping up, filling, oil change (2/2) Oil change Engine oil grade Service interval: refer Refer to the Maintenance Service Adding engine oil Maintenance Service Booklet for your Booklet for your vehicle. Use a funnel or protect the vehicle.
Page 194: Levels
LEVELS (1/3) Level 1 Topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MINI" warn- Only use fluids approved by our ing line.
Page 195 LEVELS (2/3) Checking intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 196: Filters
LEVELS /FILTERS (3/3) Filters Liquid Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, cabin filter, diesel fuel filter, etc.) is scheduled in the maintenance opera- Jets tions for your vehicle. Use a tool such as a needle to adjust Replacement intervals for filter el- the height of the windscreen washer ements: refer to the Maintenance...
Page 197: Battery
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. When the ignition is off, some consum- ers may also be switched off (dipped beam headlights, radio, ventilation, etc.). On the instrument panel, the “BATTERY MODE : ECONOMY” mes- sage appears when they are switched off.
Page 198 BATTERY (2/2) Replacing the battery For your own safety and to ensure the proper oper- ation of the vehicle’s elec- trical equipment (lights, windscreen wipers, ABS etc.), any actions on the battery (removal, dis- connection etc.) must categorically be performed by a qualified special- ist.
Page 199: Tyre Pressure
TYRE PRESSURE WHEN cold (1/2) Vehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres-  sure, etc.), the warning light lights up on the instrument panel. See “Tyre pressure loss warning” in Section 2. Label A B: front tyre pressure when driving (non-motorway), or if less than 4 people Open the driver’s door to read it.
Page 200 TYRE PRESSURE WHEN cold (2/2) Tyre dimensions The following dimensions are specific to the vehicle: – 185/70 R 14 88 T; – 195/65 R 15 91 T; For your safety, please re- – 195/65 R 15 95 T; spect the speed limit. –...
Page 201: Bodywork Maintenance
BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
Page 202 BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or Degrease or clean using freezing temperatures. high-pressure cleaning Do not scrape off mud or dirt without equipment or by spray- pre-wetting. ing on products not ap- proved by our Technical Allow dirt to accumulate on the exterior.
Page 203 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning the headlights, finish sensors and cameras Return the windscreen wiper stalk to the Park position (refer to the informa- This type of paint requires certain pre- Use a soft cloth or cotton wool.
Page 204: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display etc.) larly.
Page 205 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in Position objects such as deodorants, the vehicle perfumes etc. near air vents as this could damage your dashboard trim. If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv-...
Page 206 4.20...
Page 207 Section 5: Practical advice Puncture ..............Emergency spare wheel .
Page 208: Emergency Spare Wheel 2
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In the event of a puncture, there is Vehicle fitted with a tyre pressure either an emergency spare wheel or loss warning system tyre inflation kit available, depending on If under-inflated (puncture, low pres- the vehicle (refer to the information in ...
Page 209 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) If the emergency spare wheel has been stored for several years, have it checked by your Dealer to ensure that it is safe to use. Vehicle fitted with an emergency spare wheel that differs from the other wheels: –...
Page 210: Tyre Inflation Kit
TYRE INFLATION KIT (1/4) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 211 TYRE INFLATION KIT (2/4) Vehicle fitted with a tyre pressure loss warning system If under-inflated (puncture, low pres-  sure, etc.), the warning light lights up on the instrument panel. See “Tyre pressure loss warning” in Section 2. Before using this kit, park the vehicle at a sufficient distance from traffic, switch Depending on the vehicle, in the event...
Page 212 TYRE INFLATION KIT (3/4) – after a maximum of 15 minutes, stop inflating and read the pressure (on the pressure gauge 2). Note: while the bottle is emptying (approximately 30 seconds), the pressure gauge 2 will indicate briefly a pressure of 6 bar, then the pres- sure drops;...
Page 213 TYRE INFLATION KIT (4/4) Once the tyre is correctly inflated, Precautions when using the kit remove the kit: slowly unscrew the in- The kit should not be operated for more flation end piece to prevent any product than 15 consecutive minutes. spatter and store the container in plas- tic packaging to prevent product leaks.
Page 214: Tools
TOOL KIT (1/2) Repositioning the tool kit Put the tool kit pin 4 into the hole 3. Fit the kit correctly and tighten the wheel 2. Repositioning the tools Put them into their slots. Check every- thing is correctly positioned. Do not leave the tools un- secured inside the vehicle as they may come loose...
Page 215 TOOL KIT (2/2) Wheel brace 8 To undo the wheel bolt and the emer- gency spare wheel cage nut. Jack 9 Refer to Section 5 “Changing a wheel”. Retaining belt After use, reposition the strap making sure that it retains all components in the tool kit.
Page 216: Wheels, Trim
WHEELS, TRIM Full wheel cover 1 Full wheel cover 3 Central wheel trim 4 Remove it using hubcap tool 2 (located Remove it using hubcap tool 2 (located To remove it without removing the under the tool kit), by pushing the hook under the tool kit), by pushing the hook wheel, press it at the points indicated into the opening located near the valve...
Page 217: Changing A Wheel
CHANGING A WHEEL (1/2) Crank up jack 3 by hand to posi- tion the jack head against the jacking point closest to the relevant wheel and marked by an arrow 1. Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and aligned with the jack head).
Page 218 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Vehicle fitted with a tyre pressure For vehicles fitted with alloy wheels, loss warning system use the guide bolt located in the tool kit If under-inflated (puncture, low pres- to finish loosening and start tightening ...
Page 219: Tyres
TYRES (1/3) Tyre and wheel safety When the tyre tread has been eroded to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
Page 220 TYRES (2/3) Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure tyres are cold; ignore higher pressures loss warning system Respect the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre If under-inflated (puncture, low pres- or following a fast journey.
Page 221 TYRES (3/3) Fitting new tyres Use in winter – Studded tyres This type of equipment may only be – Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. chains to the rear axle is strictly It is necessary to observe the speed forbidden.
Page 222 LIGHTS: changing bulbs (1/2) Front side light Open the cover 1. Disconnect the bulb holder wiring 4. Remove bulb holder 4 from its housing. Replace the bulb. Bulb type: W5W To refit it, carry out the above opera- tions in reverse order. Dipped beam/main beam Bulb type: H4 It is essential to use 55W anti UV bulbs...
Page 223 LIGHTS: changing bulbs (2/2) Direction indicator lights Turn bulb holder 5 to unlock it and remove it from its location, without dis- connecting the wiring. Replace bulb . Bulb type: PY21W To refit it, carry out the above opera- To comply with local legislation, or tions in reverse order.
Page 224: Fog Lights: Changing Bulbs
FOG LIGHTS: changing bulbs Additional lights If you wish to fit your car with fog lights or long range headlights, consult an ap- proved Dealer. Please note when work- ing close to the engine that it may be hot. In addition, the engine cooling fan may ...
Page 225: Rear Lights: Changing Bulbs
REAR LIGHTS: changing bulbs (1/3) Rear lights Bulb type Depending on the vehicle, open the 4 Indicator hinged doors or the tailgate. Pear-shaped, bayonet type bulb Undo bolts 1 using a Torx tool. P Y21W. Unclip the lower section, then the upper 5 Side and brake light section of the light by pulling it towards Pear-shaped, bayonet type bulb...
Page 226 REAR LIGHTS: changing bulbs (2/3) High-level brake light Remove the two plastic blanking covers 7 from the inside. Unclip the – Version with tailgate: it is located light using a screwdriver, by pressing in above the rear screen, in the centre. the metal clip housings.
Page 227 REAR LIGHTS: changing bulbs (3/3) Number plate light Release the light to access bulbs 10. Undo two bolts 9 using a Torx tool. Bulb type: W5W. Replace the bulbs, then fit the light in position. 5.21...
Page 228: Indicator Lights: Changing Bulbs
INDICATOR LIGHTS: changing bulbs Unclip indicator light 1 on the door side, Turn bulb holder 2 a quarter of a turn using a flat-blade screwdriver type tool. and take out the bulb. Bulb type: WY5W. Replace the bulb and refit the indicator light.
Page 229: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (1/2) Passenger compartment Pull bulbs 2 and 3 downwards to remove them from their housings. lights Remove lens 1 using a tool such as a Bulb type 2: W6W flat-blade screwdriver. Bulb type 3: W5W Type of rear courtesy light bulb: W6W or, depending on the vehicle, Replace the bulbs and replace the lens.
Page 230 INTERIOR LIGHTING: changing bulbs (2/2) Light A Light B Remove the lens using a tool such as a Remove the lens using a tool such as a flat-blade screwdriver. flat-blade screwdriver. Pull the bulb to remove it from its hou- Pull the bulb to remove it from its hou- sing.
Page 231: Battery: Troubleshooting
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 232 BATTERY: troubleshooting (2/2) The two batteries must have an iden- Connect the positive (+) lead A to (+) tical nominal voltage of 12 volts. The terminal 1 of the discharged battery, battery supplying the current should then to (+) terminal 2 of the battery sup- have a capacity (amp-hours, Ah) which plying the current.
Page 233: Fuses
FUSES (1/2) To locate the fuses, please see the fol- lowing page. It is not advisable to use the free fuse locations. Some functions are protected by fuses located in the engine compartment. However, because of their reduced ac- cessibility, it is recommended to have these fuses replaced by an autho- rised dealer.
Page 234 FUSES (2/2) Number Allocation Number Allocation Fuel pump Brake lights, additional equipment, navigation, Not used ABS, ESP, boot light, tyre pressure warning light, Passenger compartment interior lights, rain and light engine cooling fan sensor Passenger compartment engine cooling fan Radio, navigation system, Rear windscreen wiper display, alarm 11 12 13 14...
Page 235 WINDSCREEN WIPER BLADES (1/2) Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and Replacing windscreen wiper Replacing windscreen wiper rear screen regularly with soapy blades 2 blades 3 water; –...
Page 236: Wiper Blades
WINDSCREEN WIPER BLADES (2/2) Replacing the rear screen Tailgate versions – In frosty weather, make wiper blade – With the ignition switched off, lift sure that the wiper blades wiper arm 9; are not stuck by ice (to Hinged door versions avoid the risk of the motor –...
Page 237: Towing: Breakdown
TOWING: breakdown (1/2) Before towing, unlock the steering The speed specified by current legis- column: press the clutch and engage lation for towing must always be ob- first gear (gear lever position N or R on served. If your vehicle is the towing vehicles fitted with an automatic gear- vehicle, do not exceed the maximum box), and insert the key in the ignition.
Page 238 TOWING: breakdown (2/2) Ensure that the towing eye is bolted correctly. Risk of losing the towed object. Access to towing points Only use the front and rear towing – Use a rigid towing bar. points (never use the driveshafts). If a rope or cable is used Unclip cover 3 or 4.
Page 239: Fitting A Radio
FITTING A RADIO (1/2) Bass speakers 5 The presence, connections and loca- tion of this equipment depend on the vehicle version. Radio location Unclip the blanking cover. The connec- tions for the aerial, + and – supply, and speaker wires are found behind the cover.
Page 240 FITTING A RADIO (2/2) Rear speakers 7 – In all cases, it is very important to follow the manufacturer’s instructions care- fully. – The specifications of the brackets and wires vary depending on the equipment level of your vehicle and the type of radio. Consult an approved Dealer to find out the correct part number.
Page 241: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
Page 242: Key, Radio Frequency Remote Control: Battery
KEY, RADIO FREQUENCY REMOTE CONTROL: battery (1/2) Replacing the battery If the battery is too weak to ensure cor- Note: it is not advisable to touch the rect operation, you can still start and electronic circuit in the key cover when Open the case at slot 1 using a flat- lock/unlock the vehicle (please refer to replacing the battery.
Page 243 KEY, RADIO FREQUENCY REMOTE CONTROL: battery (2/2) When replacing: – make sure that the batter- ies are correctly inserted. There is a risk of explosion. – if the flap does not close cor- rectly, do not use and keep out of reach of children.
Page 244: Operating Faults
OPERATING FAULTS (1/7) Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat. Use the emergency key. unlock the doors. Use of appliances operating on the same Stop using the devices or use the key. frequency as the remote control (mobile phone, etc.).
Page 245 OPERATING FAULTS (2/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons, you should always contact an approved Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are Battery terminals disconnected, Retighten, reconnect or clean them if they weak or fail to light up and the starter...
Page 246 OPERATING FAULTS (3/7) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to the correct pres- Check the tyre pressures: if this is not the sure, incorrectly balanced or dam- problem, have them checked by an ap- aged.
Page 247 OPERATING FAULTS (4/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force in the steering wheel Fault with the electric assistance needed to turn the wheels. Consult an ap- motor.
Page 248 OPERATING FAULTS (5/7) Stopped POSSIBLE CAUSES WHAT TO DO The engine cooling fan starts to run This is not necessarily a fault. The after the ignition is switched off. engine cooling fan group may start to run in order to regulate the engine temperature.
Page 249 OPERATING FAULTS (6/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information on “Fuses”...
Page 250 OPERATING FAULTS (7/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights Traces of condensation may be a nat- and headlights. ural phenomenon caused by varia- tions in temperature and humidity. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor...
Page 251 Section 6: Technical specifications Vehicle identification plates ............Engine identification .
Page 252: Vehicle Identification Plates
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MAM (Maximum Authorised hicle identification plate should be Mass). quoted on all correspondence or 5 GTW (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MPAW (Maximim Permissible The presence and location of the in- Weight) for front axle.
Page 253: Engine Identification
ENGINE IDENTIFICATION Please quote the engine identifica- tion information in area A in all cor- respondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine serial number.
Page 254: Engine Specifications
ENGINE SPECIFICATIONS (1/3) Versions 1.2 Tce 1.6 16V 1.5 dCi Engine type H5F Turbo (see engine plate) Cubic capacity (cc) 1 197 1 598 1461 Type of fuel Petrol Diesel Octane rating It is essential that you use unleaded petrol of The label located in the fuel filler flap indicates the octane rating stated on the label inside the the authorised fuels.
Page 255 ENGINE SPECIFICATIONS (2/3) Versions 1.2 Tce 1.6 16V 1.5 dCi Engine type H5F Turbo (see engine plate) Cubic capacity (cc) 1 197 1 598 1461 Fuel types that meet European standards and are Diesel fuel compliant with compatible with the engines Unleaded petrol compliant with standard EN 590 contains up standard EN 228 contains up to...
Page 256 ENGINE SPECIFICATIONS (3/3) Versions 1.2 Tce 1.6 16V 1.5 dCi Engine type H5F Turbo (see engine plate) Cubic capacity (cc) 1 197 1 598 1461 Spark plugs Only use the spark plugs specified for your vehicle’s engine. – The type should be marked on a label affixed inside the engine compartment.
Page 257: Dimensions
DIMENSIONS (in metres) (1/2)
Page 258 DIMENSIONS (in metres) (2/2) Short Medium Long H (unladen) Turning circles between kerbs 10.7 11.9 Turning circles between walls 10.1 11.2 12.4 Important: if the vehicle is fitted with roof bars, the height must be increased by 0.070 m (the bars cannot be moved).
Page 259: Weights (In Kg)
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer. Van version Estate version Maximum Permissible All-Up Weight (MMAC) Maximum permissible weight Weights are indicated on the vehicle identification plate (refer to Gross Train Weight (GTW) the information on “Vehicle identification plates”...
Page 260: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 261: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 262 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 263 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 264 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 265 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 266 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 267: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 268 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 269 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 270 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 271 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.21...
Page 272 6.22...
Page 273 ALPHABETICAL INDEX (1/5) brake lights ABS ..............1.62, 2.27 → 2.31 changing bulbs ..........5.19 – 5.20 bulbs access vehicle ..............1.7 → 1.11 changing ............5.16 → 5.24 accessories................ 5.35 accessories socket ............3.23 catalytic converter.............. 2.10 additional methods of restraint .......... 1.36 central door locking .............
Page 274 ALPHABETICAL INDEX (2/5) dipstick................ 4.4 – 4.5 filter display ........1.64 → 1.66, 1.69 → 1.72, 1.74 oil filter ..............4.6 – 4.7 doors................1.7 → 1.14 filter ..................4.10 driver’s position ............1.56 – 1.57 fitting a radio ............5.33 – 5.34 driving ......
Page 275 ALPHABETICAL INDEX (3/5) heating and air conditioning system ......3.4 → 3.15 lighting: heating system ............3.4 → 3.16 interior ............... 3.17 – 3.18 horn ................... 1.81 lights horn: adjustment ............1.85 – 1.86 flash ................1.81 changing bulbs ..........5.16 – 5.17 sounding the horn ............
Page 276 ALPHABETICAL INDEX (4/5) rear lights navigation ................3.37 changing bulbs ..........5.19 → 5.21 navigation system .............. 3.37 rear parcel shelf ..............3.33 rear screen demisting ..............3.2, 3.4 of warning sound rear seats door/luggage compartment open reminder alarm ..1.7 functions ............
Page 277 ALPHABETICAL INDEX (5/5) Stop & Start ............1.63, 2.4 → 2.7 vehicle identification ............6.2 stopping the engine ...........2.3 → 2.7 vehicle identification plates ..........6.2 storage compartment..........3.24 → 3.28 vehicle range ..............1.70 storage compartments ...........3.24 → 3.28 ventilation ..............3.2 → 3.16 sun visor ..............
Page 280 à999102315Sê ñ í ä 28 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault Kangoo 2021 User Manual

Section 1: Getting to Know Your Vehicle

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Section 6: Technical Specifications

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Renault Kangoo 2021

Summary of Contents for Renault Kangoo 2021

Table of Contents