Renault KADJAR 2021 Vehicle User Manual
  1. Manuals
  2. Brands
  3. Renault Manuals
  4. Automobile
  5. KADJAR 2021
  6. Vehicle user manual

Renault KADJAR 2021 Vehicle User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

KaDJaR
vehicle user manual

Advertisement

Table of Contents
loading

Related Manuals for Renault KADJAR 2021

Summary of Contents for Renault KADJAR 2021

  • Page 1 KaDJaR vehicle user manual...
  • Page 2 Castrol, exclusive Renault partner Benefit from cutting-edge technology born out of competition to ensure the performance and longevity of your Renault thanks to wide range of engine lubricants developed specially by Renault and Castrol. Renault recommends renault.fr...
  • Page 3 Welcome to your new vehicle This driver’s handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. –...
  • Page 5 Sections Getting to know your vehicle  ....... Driving  ..............Your comfort  ............Maintenance  ............Practical advice  ............ Technical specifications  ........Alphabetical index  ..........

  • Page 7: Table Of Contents

    Section 1: Getting to know your vehicle Key, radio frequency remote control: general information, use, deadlocking ....Card: general information, use, deadlocking ......... . . Locking, unlocking the opening elements .
  • Page 8 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves 1 Locks all the opening elements.
  • Page 9 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. Replacement and additional keys or remote controls.
  • Page 10 RADIO FREQUENCY REMOTE CONTROL UNIT: use Note: The remote control A can be used to lock or unlock the doors and boot. With the engine running, the ignition It is powered by a battery which must switched on and in accessories position be replaced (refer to the information on (refer to “Ignition switch: vehicles with a “Radio frequency remote control: bat-...
  • Page 11 RADIO FREQUENCY REMOTE CONTROL UNIT: deadlocking To activate deadlocking To deactivate deadlocking Press button 1 twice in quick succes- Unlock the vehicle using button 2. sion. The hazard warning lights flash once The hazard warning lights and indicator to indicate that the doors have been un- lights give two slow flashes and three locked.
  • Page 12 CARD: general information (1/3) The card is used for: card operating range – locking/unlocking the doors and boot This varies according to the surround- (see the following pages); ings. It is important to make sure when handling the card that you do not lock –...
  • Page 13 CARD: general information (2/3) Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the card in a place Driver’s responsibility where it could be bent or dam- when parking or stopping aged accidentally, such as in a back the vehicle pocket of a garment.
  • Page 14 CARD: general information (3/3) Fitting a hand strap 7 Insert the hand strap into the 8 com- ponent and pass the end of the strap Slide the rear casing 5 downwards through the buckle. while pressing on zone A. Position the strap at the 6 opening and close the cartridge.
  • Page 15 “HANDS-FREE” CARD: use (1/4) There are two ways to unlock/lock the vehicle: – the card in “hands-free” mode; – the card in remote control mode. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time.
  • Page 16 “HANDS-FREE” CARD: use (2/4) To indicate that the vehicle has been locked, the hazard warning lights and indicator lights flash once and then light up for approximately four sec- onds, and a beep sounds in confirma- tion. Locking using button 2 With the doors and boot closed, press button 2 on one of the front door han- dles.
  • Page 17 “HANDS-FREE” CARD: use (3/4) Locking using the card With the doors and boot closed, press button 6: the vehicle locks. The indicator lights and hazard warning lights flash twice to indicate that the doors have locked. NB: The maximum distance at which the vehicle locks depends on the sur- roundings.
  • Page 18 “HANDS-FREE” CARD: use (4/4) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Locking/unlocking only the If, while the engine is running, a door or to others by starting the engine,...
  • Page 19 CARD: deadlocking Special feature The deadlocking cannot be activated when the hazard warning lights or the side lights are lit. To deactivate deadlocking Unlock the vehicle using button 1 on the card. Unlocking is indicated by one flash of the hazard warning lights and the indi- cator lights.
  • Page 20 LOCKING, UNLOCKING THE DOORS (1/3) If the remote control or, It is then possible: depending on the vehicle, the – depending on the vehicle, use the card does not work radio frequency remote control or the emergency key integrated in the In some cases, the radio frequency card to unlock the front left-hand remote control or the card may not...
  • Page 21 LOCKING, UNLOCKING THE DOORS (2/3) Vehicles with card Using the integrated key Insert the key 4 into the lock 1 and lock Access key 4 integrated in the card or unlock the front left-hand door. Slide the rear casing 3 downwards Once you are inside the vehicle, put the while pressing on zone A.
  • Page 22 LOCKING, UNLOCKING THE DOORS (3/3) If a door or the tailgate is open or not Unlocking the vehicle from the outside closed properly, the doors and tailgate is only possible with the card in the ve- lock/unlock quickly. hicle access zone or by using the key. If transporting an object with the tail- gate open, you can still lock the doors: Door and tailgate status...

  • Page 23: Opening And Closing The Doors

    OPENING AND CLOSING THE DOORS (1/2) Opening the doors from the Opening from the inside Door/tailgate open buzzer outside Pull the handle 3. At a standstill, the warning light 4 lights up on the instrument panel alongside With the doors unlocked, pull handle 1. Lights-on reminder buzzer the warning light 5 indicating the...
  • Page 24 OPENING AND CLOSING THE DOORS (2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Child safety Vehicle with manual door locking or to others by starting the engine,...

  • Page 25: Automatic Locking When Driving

    AUTOMATIC LOCKING WHEN DRIVING Operating faults NB: if a door is opened or closed, it will automatically lock again when the If you experience an operating fault vehicle reaches a speed of 6 mph (no automatic locking, the indicator (10 km/h). light incorporated in switch 1 does not light up when trying to lock the open- Activating/deactivating the...
  • Page 26 FRONT HEADRESTS To raise the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary). Press button 3 and lift the headrest to release it. To refit the headrest Check that the headrest rods are clean 2.
  • Page 27 FRONT SEATS WITH MANUAL CONTROL (1/2) To raise or lower the seat base Move lever 3 as many times as neces- sary upwards or downwards. To tilt the seatback Lift the lever 4 and move the seatback to the desired position. To move the seat forwards or To adjust the lumbar support backwards...
  • Page 28 FRONT SEATS WITH MANUAL CONTROL (2/2) Repositioning the seat When using the passenger seat in table position, you must not use the two rear Make sure that nothing prevents the seats immediately behind it. seat from moving. – Pull the handle 7 and raise the seat- back, ensuring that it locks firmly in place.
  • Page 29 DRIVER’S SEAT WITH ELECTRIC CONTROLS Heated seats With the ignition on, press the switch 5 for the seat desired. The switch warn- ing lights come on. The system automatically decides whether or not the heating is needed. Pressing the button again lowers the temperature.

  • Page 30: Seat Belts

    SEAT BELTS (1/5) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants to adjust their seat belts to ensure comply with the legislation of the par- ticular country you are in.
  • Page 31 SEAT BELTS (2/5) ß Driver’s seat belt reminder and, depending on the vehi- cle, front passenger seat belt re- minder This appears on the central display when the ignition is switched on and if the driver’s or front passenger’s seat belt (when the passenger seat is occu- pied) is not fastened.
  • Page 32 SEAT BELTS (3/5) Unfastening Rear seat belt reminder (depending on vehicle) Press button 4 and the seat belt will be ß rewound by the inertia reel. Guide the warning light is displayed belt. on the central display each time the ignition is switched on.
  • Page 33 SEAT BELTS (4/5) Adjusting the height of the Rear seat belts 8 front seat belts The belts are locked, unlocked and adjusted in the same way as the front Use button 7 to adjust the seat belt belts. height so that the shoulder strap is worn as shown previously.
  • Page 34 SEAT BELTS (5/5) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
  • Page 35 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/6) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
  • Page 36 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/6) Load limiter driver and passenger front Airbags Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger the belt against the body so that it is at sides.
  • Page 37 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/6) Operating faults å This warning light will light up on the instrument panel when the ignition is switched on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system.
  • Page 38 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/6) The following cases cause the pre- In a frontal impact with another vehi- In a side impact with another vehicle tensioners or airbags to operate cle of an equivalent or higher category, of an equivalent or higher category, at with an impact area equal to or greater an impact speed equal to or greater...
  • Page 39 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/6) In the following examples, the pre- In the following examples, there is a – side impact, affecting the front of the tensioners or the airbags could op- risk that pretensioners orairbags may vehicle;...
  • Page 40 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (6/6) All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. Warnings concerning the driver’s airbag –...
  • Page 41 METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
  • Page 42 SIDE PROTECTION DEVICES Side Airbags An airbag can be fitted to each front seat and the rear side seats, which are deployed on the side of the seat (door side) to protect the occupants in the case of a severe side impact. Curtain Airbags These are airbag fitted along the sides of the vehicle in the ceiling which trigger...

  • Page 43: Additional Methods Of Restraint

    ADDITIONAL METHODS OF RESTRAINT Operating faults All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused å by items which may be dislodged when it inflates. This warning light comes on when the engine is started and then The airbag is designed to complement the action of the seat belt.

  • Page 44: Child Safety: General Information

    CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. Driver’s responsibility A child is not a miniature adult.
  • Page 45 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 46 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier Up to 18 kg or 4 years, the child may From 15 kg or 4 years, the child can than that of an adult and its neck is very travel on a forward-facing seat.

  • Page 47: Choosing A Child Seat Mounting

    CHILD SAFETY: choosing a child seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised ISOFIX child seats are ap- chased for another vehicle, proved in accordance with regulation check that its installation is...
  • Page 48 CHILD SAFETY: choosing a child seat mounting (2/2) The rings are identified by the symbol  In all cases, attach the strap hook to the corresponding ring 2 and 3 and place the seat in the desired position. Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat.

  • Page 49: Fitting A Child Seat, General Information

    CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, when this child seats. The diagram on the follow- is possible, you can move the vehi- The laws concerning children travel- ing page shows you how to attach a cle seat forward if necessary (so as to...
  • Page 50 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Fit the child seat in a rear Position the child with their feet nearest seat wherever possible.
  • Page 51 CHILD SEATS: attachment by seat belt (1/3) ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats. Child seat attached using the belt ¬...
  • Page 52 CHILD SEATS: attachment by seat belt (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. Front passenger Type of child seat Weight of the child Rear side seats Rear centre seat seat...
  • Page 53 CHILD SEATS: attachment by seat belt (3/3) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
  • Page 54 CHILD SEATS: attachment using the ISOFIX SYSTEM ( 1/3) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Front passenger seat Rear centre Rear side seat seats Weight of Seat size...
  • Page 55 CHILD SEATS: attachment using the ISOFIX SYSTEM ( 2/3) X = Seat not suitable for fitting child seats of this type. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system;...
  • Page 56 CHILD SEATS: attachment using the ISOFIX SYSTEM ( 3/3) Child seat fitted using the ISOFIX mounting ü Seat which allows a ISOFIX child seat to be attached. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
  • Page 57 CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3) DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat, NEVER fit a rear-facing child re- straint system in a seat protected by an ACTIVATED front AIRBAG.
  • Page 58 CHILD SAFETY: deactivating, activating AIRBAG front passenger (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (example: label shown above) remind you of these instruc- tions. DANGER Since operation of the front passenger airbag is not compatible with the po- sition of a rear-facing child seat,...
  • Page 59 CHILD SAFETY: deactivating, activating AIRBAG front passenger (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.

  • Page 60: Driving Position

    DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1.54...

  • Page 61: Instrument Panel

    DRIVING POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 10 Controls for: 1 Air vent. 19 Assisted parking or handbrake 2 Demister outlet. – access the main menu; control. 3 Stalk for: – access the “Driving assistance” 20 Gear lever.
  • Page 62 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 10 11 1.56...
  • Page 63 DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 10 Instrument panel. 1 Air vent. 16 Bonnet release control. 2 Demister outlet. 11 Driver Airbag and horn location. 17 Ignition switch (vehicles with key). 3 Passenger Airbag location.
  • Page 64 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. š Side light warning light Left-hand direction indicator tell-tale á Main beam headlight tell- Right-hand direction indica- tale tor tell-tale Dipped beam headlight tell- Low fuel level warning light tale It lights up orange when the ig-...
  • Page 65 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. À Brake circuit fault warning Oil pressure warning light light It lights up when the ignition or It lights up when the ignition or the the engine is switched on and goes off engine is switched on and goes off after after a few seconds.
  • Page 66 WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ä Toxic Fume Filter System Anti-lock braking warning Warning Light light On vehicles which are equipped with it, It lights up when the ignition or the this light comes on when the engine is engine is switched on and goes off after started and, depending on the vehicle,...
  • Page 67 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Š ‰ Ó Gear change indicator Brake pedal warning light This lights up to advise you to This lights up when the brake change to a higher gear (up arrow) or pedal should be depressed.
  • Page 68 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Φ  Speed limiter and cruise Mode warning light ECO control indicator lights This comes on when ECO See the information on the “Speed lim- mode is activated.
  • Page 69 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.  ß Assisted parking brake fault Driver’s seat belt reminder light and, depending on the vehi- cle, front passenger seat belt re- Please refer to the information on the minder “Assisted parking brake”...
  • Page 70 DISPLAYS AND INDICATORS (1/2) Instrument panel A Driving style indicator 3 Instrument panel in miles (option to switch to km/h) You can customise your instrument Please refer to the information on “Eco- panel with the content and colours of driving” in Section 2. Vehicles not fitted with a navigation your choice.

  • Page 71: Trip Computer

    DISPLAYS AND INDICATORS (2/2) Coolant temperature Engine oil level low warning Vehicles fitted with a navigation system indicator 6 When the engine is started, the instru- On the multifunction screen, select ment panel display A alerts you when “System” , “User profile” and “Unit”. the minimum oil level is reached.
  • Page 72 TRIP COMPUTER: general information (1/2) Display selection keys 2 Scroll through the following information by repeated short presses on the con- trol 2 (the display depends on the vehi- cle equipment and country): a) total mileage and trip mileage re- corder;...
  • Page 73 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
  • Page 74 ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101 778 km 112,4 km a) Total mileage and trip mileage recorder. Fuel used b) Journey parameters: Fuel consumed since the last reset.
  • Page 75 ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range Estimated range with remaining fuel. The value is displayed after driving 400 metres. 541 km Distance Distance travelled since last reset.
  • Page 76 ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message c) Mileage before service or oil change. Mileage before service Service in SERVICE With the ignition switched on, the engine not running and...
  • Page 77 TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) c) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on, the engine not running and...
  • Page 78 ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Reset the tyre pressure. Refer to the information on the “Tyre pressure monitor- Tyre pressure ing system”...
  • Page 79 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected «...
  • Page 80 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
  • Page 81 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.

  • Page 82: Vehicle Settings Customisation Menu

    VEHICLE SETTINGS CUSTOMISATION MENU (1/2) Adjusting the settings Select the function to modify: a) unlocking the driver’s door; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome; g) reading lamp in automatic mode;...
  • Page 83 VEHICLE SETTINGS CUSTOMISATION MENU (2/2) Adjusting the settings If you select either “PARKING ASSIST Volume” or “LANGUAGE”, you will Browse using the control 4 to select the have to make a further selection (sound function to adjust: volume of the parking distance control a) Auto door lock while driving;...

  • Page 84: Steering Wheel/Power-Assisted Steering

    STEERING WHEEL, POWER-ASSISTED STEERING Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).

  • Page 85: Rear View Mirrors

    REAR VIEW MIRRORS (1/2) Folding rear view mirrors Welcome and goodbye function Refer to the multimedia instructions to The door mirrors automatically fold in access the welcome and goodbye func- when the vehicle is locked (switch 3 in tion. position B). Activate or deactivate the function by In any case, you can make the door selecting (ON or OFF).
  • Page 86 REAR VIEW MIRRORS (2/2) Interior rear view mirror Rear view mirror without lever 4 The rear-view mirror darkens automati- Rear view mirror with lever 4 cally at night if you are being followed When driving at night, to avoid being by a vehicle with its lights on.
  • Page 87 CLOCK AND EXTERIOR TEMPERATURE External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (sig- nalling a risk of ice on the road). Display 1 Vehicles fitted with a multimedia screen, navigation systems etc.

  • Page 88: Exterior Lighting And Signals

    EXTERIOR LIGHTING AND SIGNALS (1/6) Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the in- strument panel comes on. Automatic operation Turn the ring 3 until the AUTO symbol is opposite the mark 2: with the engine running, the dipped beam headlights switch on or off automatically depend-...
  • Page 89 EXTERIOR LIGHTING AND SIGNALS (2/6)  Automatic main beam headlights Depending on the vehicle, this system switches the main beam headlights on and off automatically. It uses a camera located behind the interior rear-view mirror to detect vehicles that are being followed and those coming in the oppo- site direction.
  • Page 90 EXTERIOR LIGHTING AND SIGNALS (3/6) Activation/deactivation To activate the automatic main beam headlights: – turn the ring 3 until the AUTO symbol is opposite the mark 2; – push stalk 1.  Warning light comes on the in- strument panel. To deactivate the automatic main beam headlights: –...
  • Page 91 EXTERIOR LIGHTING AND SIGNALS (4/6) Daytime running lights Switching off the lights function There are two possibilities: – manually, move ring 3 to position 0; The daytime running lights come on – automatically, the lights will go out automatically with no action on stalk 1 when the engine is switched off, the when the engine is started, and they go driver’s door is opened or the vehicle...
  • Page 92 EXTERIOR LIGHTING AND SIGNALS (5/6) “See-me-home lighting” Welcome and goodbye Activating/deactivating the function function function From the multimedia screen, select (depending on the vehicle) “Vehicle”, “User settings”, “External This function allows you to briefly switch welcome”. Choose “ON” or “OFF” to on the dipped beam headlights (to pro- When the function is activated, the rear activate or deactivate the function.
  • Page 93 EXTERIOR LIGHTING AND SIGNALS (6/6) Rear fog lights Switching off the lights  Turn centre ring 7 on the stalk Turn the ring 7 again until the mark 2 until the symbol faces mark 2, then re- is opposite the symbol for the fog light lease it.

  • Page 94: Audible And Visual Signals

    AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.

  • Page 95: Headlight Beam Adjustment

    HEADLIGHT BEAM ADJUSTMENT For manual settings Examples of adjustment positions of control A according to the load and the headlight Halogen headlights LED headlight Driver alone or with front passenger All seats occupied On vehicles fitted with this function, control A allows you to adjust the height Driver with passengers and of the beams according to the load.
  • Page 96 WINDSCREEN WASH, WIPE (1/6) Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: – it must remain clean: clean the blade and the screen regularly with soapy water; – do not use it when the screen is dry;...
  • Page 97 WINDSCREEN WASH, WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of re- duced visibility, the driver should manually activate the wipers;...
  • Page 98 WINDSCREEN WASH, WIPE (3/6) Operating fault Special note In the event of a malfunction of the When driving the vehicle, the wiping automatic wiping, the wiper is set to speed slows down whenever the ve- intermittent wiping. Contact an au- hicle stops.
  • Page 99 WINDSCREEN WASH, WIPE (4/6) Specific front wiper position Note: after replacement, to reposition the blades correctly, make sure the (service position) blades are resting on the windscreen, This position enables the blades to be switch on the ignition and activate the lifted to remove them from the winds- wiper control.
  • Page 100 WINDSCREEN WASH, WIPE (5/6) Note: in temperatures below zero, the washer liquid may freeze on the wind- screen, reducing visibility. Heat the windscreen using the demister control before cleaning. Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the wind- screen washer.
  • Page 101 WINDSCREEN WASH, WIPE (6/6) Note To ensure the headlight washers op- erate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. You are recommended to regularly remove dirt encrusted on the headlight glass.
  • Page 102 REAR SCREEN WASH, WIPE (1/2) To stop the operation, pivot ring 3 again. Note: when washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate Efficiency of a wiper blade automatic wiping.
  • Page 103 REAR SCREEN WASH, WIPE (2/2) Activation/deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper (depending on the vehicle) will try to sweep away all the obstacles. If an obstacle prevents the blade from Engaging reverse gear triggers inter- moving, it can be stopped.
  • Page 104 TANK (1/3) Fuel tank Use the cap holder 2 on the flap 1 during filling to hold the cap 3 in place. Useable tank capacity: Filler cap: this is specific. – Approximately 12.1 gal (55 litres) or 14.3 gal (65 litres) for 2-wheel ver- If you have to replace it, sions, depending on the vehicle;...
  • Page 105 TANK (2/3) Fuel grade Filling with fuel engine must Use a high-grade fuel that complies With the ignition off, insert the nozzle switched off for refuelling with the legislation in force in each and insert it fully before turning it on to (and not just on standby country and which must comply with fill the fuel tank (risk of splashing).

  • Page 106: Fuel Tank (Filling With Fuel)

    FUEL TANK (3/3) Running out of fuel on diesel versions No modifications what- Vehicles with key/remote control soever are permitted on any part of the fuel supply – Put the ignition key in “On” position M system (electronic units, (please see the information on the wiring, fuel circuit, injectors, pro- “Ignition switch”...

  • Page 107: Reagent Tank

    REAGENT TANK (1/4) Please ensure that you comply with the legislation of your country. It is impor- tant to remember that failure to respect regulations in force could lead to legal To fill up with reagent, the engine action being taken against the vehicle must be stopped (not just on owner.
  • Page 108 REAGENT TANK (2/4) Filling (continued) If the reagent overflows, or contami- nates any paintwork, clean the affected The tank can be filled at the pump. With area quickly with plenty of cold water the ignition off, insert the nozzle and and a soft cloth.
  • Page 109 REAGENT TANK (3/4) Maintenance/Range The information displayed on the instrument panel may be accompanied by a beep. Indicator Message What to do? lights When the message is displayed when the ignition is switched on, you have less than 1,488 miles (2,400 km) range. –...
  • Page 110 REAGENT TANK (4/4) System fault When the indicator lights light up, this may be accompanied by a beep. Indicator lights Message Readings “Check anti-pollution system” Indicates a fault in the system. Contact your approved  “AdBlue quality to check” © dealer as soon as possible.
  • Page 111 Section 2: Driving (advice on use relating to fuel economy and the environment) Running in ..............Starting, stopping the engine: vehicle with key/remote control unit .

  • Page 112: Running In

    RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm.

  • Page 113: Starting, Stopping The Engine: Vehicle With Key/Remote Control Unit

    STARTING, STOPPING THE ENGINE: vehicle with key É Stopping the engine Diesel versions With the engine idling, turn the key to – Turn the ignition key to the the “Stop” position St. “Ignition on” position M, and hold this position until the engine pre- heating light goes off;...

  • Page 114: Starting, Stopping The Engine: Vehicle With Card

    STARTING, STOPPING THE ENGINE: vehicle with card (1/3) “Hands-free” starting with the tailgate open In this case, the card should not be lo- cated in the luggage compartment, to prevent the risk of loss. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi-...
  • Page 115 STARTING, STOPPING THE ENGINE: vehicle with card (2/3) Depress the brake or clutch pedal, then place the card 3 (logo side) in contact with the start button 2 for around 2 sec- onds. Press the 2 button to start the ve- hicle.
  • Page 116 STARTING, STOPPING THE ENGINE: vehicle with card (3/3) If the card is no longer in the passenger compartment or if the card’s battery is When you leave your vehi- low when you try to switch the engine cle, especially if you have off, the message “No keycard Press your card with you, check and hold”...
  • Page 117 FUNCTION STOP AND START (1/4) This system enables a reduced fuel For manual gearboxes: consumption and lower greenhouse – the gearbox is in neutral; gas emissions. The system is activated automatically – the clutch pedal is released. If the  when the vehicle is started.
  • Page 118 FUNCTION STOP AND START (2/4) Preventing the engine from Conditions for coming out of Special note: depending on the vehi- cle, if you switch off the ignition when standing by engine standby the engine is on standby, the warning Ä In certain situations, such as negotiat- For automatic gearboxes: light...
  • Page 119 FUNCTION STOP AND START (3/4) Conditions preventing the Special cases for vehicles – the gradient is too steep for vehicles fitted with an automatic gearbox; standby of the engine with a card – the “clear view” function is activated Certain conditions prevent the system With the engine on standby (traffic jam, (please see “Automatic climate con- from using the engine standby function,...
  • Page 120 THE STOP AND START function (4/4) Special feature of the automatic The system is automatically reacti- engine re-start vated each time the vehicle is started (see “Starting, stopping the engine” in Under certain conditions, the engine Section 2). can restart on its own in order to guar- antee your safety and comfort.

  • Page 121: Special Features Of Petrol Versions, Particle Filter

    SPECIAL FEATURES OF PETROL VERSIONS, PARTICLE FILTER (1/2) The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...

  • Page 122: Particle Filter

    SPECIAL FEATURES OF PETROL VERSIONS, PARTICLE FILTER (2/2) Particle filter Note: the indicator light may go out If the filter becomes saturated, the © after 20 minutes if the driving condi- warning light and, depending The particle filter is used in the treat- ...

  • Page 123: Special Features Of Diesel Versions

    SPECIAL FEATURES OF DIESEL VERSIONS (1/2) Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- tion pump which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of –...
  • Page 124 SPECIAL FEATURES OF DIESEL VERSIONS (2/2) Particle filter Note: the warning light may re-appear If the filter becomes saturated, the © if the driving conditions are not suitable warning light and, depending The particle filter is used in the treat- ...
  • Page 125 GEAR LEVER Selecting reverse gear The ring 2 has to be lifted up to the gear lever knob to select reverse gear. The reversing lights will come on as soon as reverse gear is selected with the ignition on. Note: depending on the vehicle, if the dipped beam headlights are on, the front fog lights come on simultaneously when reverse gear is selected.

  • Page 126: Handbrake

    HANDBRAKE When stationary, and de- pending on the slope and/or vehicle load, it may be nec- essary to pull up the hand- Handbrake brake at least two extra notches and engage a gear (1 or reverse gear) To release: for vehicles with a manual gearbox Pull lever 2 up slightly, press button 1 or position P for vehicles with an au- and then lower the lever to the floor.

  • Page 127: Electronic Parking Brake

    ELECTRONIC PARKING BRAKE (1/5) In all other circumstances, for example, stalled engine or engine switched to standby by the Stop and Start func- tion (refer to the information on the “Stop and Start function” in Section 2), the electronic parking brake is not ap- plied automatically.
  • Page 128 ELECTRONIC PARKING BRAKE (2/5) Assisted operation Note: in some situations (electronic parking brake failure, manual release of (continued) the parking brake, etc.), a beep sounds For certain country-specific model ver- and the message “Apply parking brake” sions, the assisted brake application appears on the instrument panel to function is not activated.
  • Page 129 ELECTRONIC PARKING BRAKE (3/5) Manual operation Manually releasing the electronic parking brake You can apply the electronic parking Press the switch 1 without pressing brake manually. the brake pedals or turn the key 2 to Manually applying the electronic the “ON” position to switch on the igni- parking brake tion.
  • Page 130 ELECTRONIC PARKING BRAKE (4/5) To park the vehicle without applying the electronic parking brake (if there is a risk of freezing, for example): – engage any gear or the P position: the drive wheels will be mechanically locked by the driveshaft; –...
  • Page 131 ELECTRONIC PARKING BRAKE (5/5) Versions with an automatic Operating faults gearbox © – If there is a fault, the warning light illuminates on the instrument For safety reasons, automatic release panel accompanied by the “Check is deactivated when the driver’s door Parking Brake”...

  • Page 132: Eco Driving

    DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- – in green or white, depending on the cordance with a standard regulatory vehicle, when the vehicle is in free- method. Identical for all manufactur- wheel mode (automatic neutral). ers, this enables vehicles to be com- pared with one another.
  • Page 133 DRIVING ADVICE, ECO-DRIVING (2/5) On the multifunction screen Journey record Once the engine is switched off, you will see “Journey record” displayed on the screen 4, enabling you to view in- formation relating to your last journey. This indicates: – average fuel consumption; –...
  • Page 134 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode Activating the function The function can be activated: ECO mode is a function which opti- mises fuel consumption. It affects cer- – by pressing switch 4; tain driving operations (acceleration, – Depending on the vehicle, from the shifting gears, cruise control, decelera- navigation menu on the multimedia tion etc.).
  • Page 135 DRIVING ADVICE, ECO-DRIVING (4/5) – Do not overrev the engine in the in- – Bad weather, flooded roads: termediate gears. Do not drive through You should always use the highest floods if the water is gear possible. above the lower edge of –...
  • Page 136 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.

  • Page 137: Maintenance And Antipollution Advice

    MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele- recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must end of their service life, which entered nents with parts other than those origi- be replaced.

  • Page 138: Environment

    ENVIRONMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Your vehicle has been designed to emit its entire service life: during production, centres to ensure that it is recycled.

  • Page 139: Tyre Pressure Monitoring System

    TYRE PRESSURE MONITORING SYSTEM (1/3) Resetting the standard level Resetting procedure for the tyre pressures With the ignition on: – repeatedly and briefly press control 2 This should be done: to select the tyre pressure display – when the standard tyre pressure and the “Tyre pressure”...
  • Page 140 TYRE PRESSURE MONITORING SYSTEM (2/3) “Puncture” A wheel Bis shown in red, the warning  light 4 comes on, the message “Puncture” appears and there is a beep. This message appears along with the ® warning light. They indicate that the affected wheel is punctured or severely underinflated.
  • Page 141 Because the valves are specially de- wheels have been fitted with sensors Please see the information on “Tyres” signed, only use equipment approved not recognised by Renault. in Section 5. by the approved network. Please refer Contact an approved Dealer to fit new to “Tyre inflation kit”...

  • Page 142: Driver Correction Devices And Aids

    DRIVER CORRECTION DEVICES AND AIDS (1/6) ABS (anti-lock braking Depending on the vehicle, they will con- sist of: system) Under heavy braking, the ABS prevents – ABS (anti-lock braking system) ; the wheels from locking, allowing the – ESC (electronic stability control) stopping distance to be managed and with understeer control and trac- keeping control of the vehicle.
  • Page 143 DRIVER CORRECTION DEVICES AND AIDS (2/6) Operating faults: © – lit up on the in- strument panel accompanied by the messages “Check ABS”, “WARNING: Check Braking System” and “Check ESC”: this indicates that the ABS, the ESC and the emer- gency brake assist are disabled.
  • Page 144 DRIVER CORRECTION DEVICES AND AIDS (3/6) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operating and traction control ESC in the case of pronounced under- fault the message “Check ESC”...
  • Page 145 DRIVER CORRECTION DEVICES AND AIDS (4/6) The traction control system offers ad- ditional safety. It is recommended that you do not drive with the function dis- abled. Correct this as soon as possible by pressing switch 1 again. Note: the function is reactivated auto- matically when the ignition is switched on or when a speed of approximately 25 mph (40 km/h) is exceeded.
  • Page 146 DRIVER CORRECTION DEVICES AND AIDS (5/6) Advanced traction control “Soft ground” mode Turn the selector 2: the integrated If fitted on the vehicle, traction control  makes it easier to control the vehicle on warning light comes on, accom- low grip surfaces (soft ground, etc.). panied by a message on the instrument panel “Grip Extend Loose Surface ON”.
  • Page 147 DRIVER CORRECTION DEVICES AND AIDS (6/6) Hill start assistance “Expert” mode Turn the selector 2: the integrated Depending on the gradient of the in-  cline, this system assists the driver warning light comes on, accom- when starting on a hill. It prevents the panied by a message on the instrument vehicle from rolling backwards by au- panel “Grip Extend Expert Mode ON”.

  • Page 148: Active Emergency Braking

    ACTIVE EMERGENCY BRAKING (1/4) If the driver depresses the brake pedal and the system still detects a risk of col- lision, the brake force is increased. If the driver fails to react following an alert of an imminent collision, the system activates the brakes.
  • Page 149 ACTIVE EMERGENCY BRAKING (2/4) Press the switch 5 OK again to activate or deactivate the function: function activated < function deactivated  The warning light is displayed on the instrument panel when the system is deactivated. This system is reacti- vated each time the ignition is switched Conditions for non-activation of the system...
  • Page 150 ACTIVE EMERGENCY BRAKING (3/4) Temporarily not available If the system detects a temporary fault,  warning light appears on the instrument panel. The possible causes are: Active emergency braking – the system is temporarily disrupted This function is an additional driving aid. However, this function is not (for example: radar obscured by under any circumstances intended to replace the due care and attention dirt, mud, snow etc.).
  • Page 151 ACTIVE EMERGENCY BRAKING (4/4) Active emergency braking Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. –...

  • Page 152: Transmission: 4-Wheel Drive (4Wd)

    TRANSMISSION: 4-wheel drive (4WD) (1/4) Mode selector “2WD" mode Depending on the road conditions, turn- To activate this mode, turn the selec- ing the selector 1 enables the following tor 1 to the “2WD” position. The warn- ‘ modes to be selected: ing light on the instrument panel –...
  • Page 153 TRANSMISSION: 4-wheel drive (4WD) (2/4) “4WD Lock" mode Note: If the vehicle speed exceeds This problem may be resolved by approximately 24.8 mph (40 km/h) in changing the tyres. Always use four To activate this mode, turn selector 1 to “4WD Lock”...
  • Page 154 TRANSMISSION: 4-wheel drive (4WD) (3/4) Operating faults After stopping the engine, the system Electronic stability program and may take up to five minutes to cool traction control when driving off- If the system detects an operating fault, road down. it automatically switches to “2WD” If the system detects excessive wheel- When driving on soft ground (sand, mode.
  • Page 155 TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). –...

  • Page 156: Lane Departure Warning

    LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
  • Page 157 LANE DEPARTURE WARNING (2/3) Activation/deactivation Vehicles not fitted with a navigation The function is set to notify the system driver if: Vehicles fitted with a navigation – the vehicle speed is greater than ap- Press the switch 3. system proximately 45 mph (70 km/h); From the multimedia screen2: select Operation –...
  • Page 158 LANE DEPARTURE WARNING (3/3) Adjustment – repeatedly press control 6 up or down until you reach the “Lane de- Vehicles fitted with a navigation parture warning settings” menu, then system press the switch 5 OK. – Volume: adjust the alert volume to From the multimedia screen 2, select one of three levels;...

  • Page 159: Blind Spot Warning

    BLIND SPOT WARNING (1/4) Special feature This system alerts the driver to other vehicles in the detection zone A. Make sure that the sensors are not ob- scured (by dirt, mud, snow, etc.). The system is activated when the vehi- If a sensor is obscured, the message cle’s speed is between approximately “Blind spotclean sensor”...
  • Page 160 BLIND SPOT WARNING (2/4) – repeatedly press control 5 up or down until you reach the “Blind spot alert” menu, then press the switch 4 – Press the switch 4 OK again to acti- vate or deactivate the function. Activation/deactivation Vehicles not fitted with a navigation system Vehicles fitted with a navigation...
  • Page 161 BLIND SPOT WARNING (3/4) Display B The function is activated and has not detected any vehicles. Display C Initial warning: the indicator light 4 shows that a vehicle has been detected in the blind spot. Display D When the direction indicator is acti- vated, the indicator light 4 flashes when a vehicle is detected in the blind spot on the side towards which you are about to...
  • Page 162 BLIND SPOT WARNING (4/4) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- played on the instrument panel. Consult an authorised dealer. Note: When the engine is started, the indicator light 4 (display B) flashes three times.

  • Page 163: Speed Limiter

    SPEED LIMITER (1/3) Switching on  Press switch 1 on side . Indicator  light comes on, lit orange, and the message “Speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed lim- iter function is activated and waiting to store a limit speed.
  • Page 164 SPEED LIMITER (2/3) Varying the limit speed Limited speed cannot be maintained When driving down a steep gradient, The speed limiter can be changed by the system is unable to maintain the repeatedly pressing the switch 2: limit speed: the memorised speed will –...
  • Page 165 SPEED LIMITER (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 3 (R). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is sus- case a speed is no longer stored.
  • Page 166 OVERSPEED ALERT (1/3) Operating principle Once the speed limiter is activated, you can adjust the speed limiter indication The system detects speed limit signs displayed by the system. on the side of the road and displays the In the event of exceeding the speed speed limit.
  • Page 167 OVERSPEED ALERT (2/3) – repeatedly press the control 6 up or down until you reach the Speed alert menu, then press the switch 5 OK. – Press OK to turn the function on or off. Varying the limit speed If the speed limiter notification differs from the detected speed value, press and hold the switch 4: –...
  • Page 168 OVERSPEED ALERT (3/3) Operating fault This function is an additional driving aid. However, this function is not The system cannot detect the speed under any circumstances intended to replace the due care and attention limit if: of the driver, who should at all times be in control of the vehicle. –...

  • Page 169: Cruise Control

    CRUISE CONTROL (1/4) This function is an addi- tional driving aid. The func- tion does not take the place Controls The cruise control function helps you to of the driver. Therefore, it maintain your driving speed at a speed 1 Main “On/Off” switch. can under no circumstances replace that you choose, called the cruising the driver’s responsibility to respect...
  • Page 170 CRUISE CONTROL (2/4) Activating cruise control At a steady speed (above approxi- mately 19 mph (30 km/h)) press the switch 2 on the a (+) side: the function is activated and the current speed is stored. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Cruise ...
  • Page 171 CRUISE CONTROL (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While overtaking, the cruis- ing speed flashes red on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
  • Page 172 CRUISE CONTROL (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press the switch 3 (R) if the vehicle speed is above 19 mph (30 km/h).

  • Page 173: Adaptive Cruise Control

    ADAPTIVE CRUISE CONTROL (1/7) When traffic conditions permit (large free-flowing road or motorway), the adaptive cruise control gives you the option of maintaining a chosen speed, known as the cruising speed, which can be set from 31 mph to 87 mph (50 and 140 km/h), or 93 mph (150 km/h) de- pending on the vehicle, while keeping a following distance from the vehicle in...
  • Page 174 ADAPTIVE CRUISE CONTROL (2/7) Controls Switching on The cruising speed replaces the dashes and cruise control is confirmed by the Press switch 5. Indicator light  5 Main “On/Off” switch. appearance of the message “Adaptive comes on, lit green, and the message 2 Controls for: cruise ctrl”...
  • Page 175 ADAPTIVE CRUISE CONTROL (3/7) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, You can vary the following distance you may lift your foot off the accelera- from the vehicle in front at any time by tor pedal.
  • Page 176 ADAPTIVE CRUISE CONTROL (4/7) Putting the function on Returning to the cruising speed standby If a speed is stored, it can be recalled, once you are sure that the road con- The function is set to standby if: ditions are suitable (traffic, road sur- –...
  • Page 177 ADAPTIVE CRUISE CONTROL (5/7) Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate to reach this threshold. Under certain conditions (coming up behind a vehicle moving more slowly, rapid change of lane of vehicles in front etc.), the system may not have time to respond and may emit a beep along- side the alert B when the situation re-...
  • Page 178 ADAPTIVE CRUISE CONTROL (6/7) Operating faults When the system detects an operating  fault, the warning light lights up on the instrument panel, with the mes- sage “Check cruise control”. There are two possibilities: – the system is temporarily disrupted (for example: radar obscured by dirt, mud, snow etc.).
  • Page 179 ADAPTIVE CRUISE CONTROL (7/7) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The sensor area should be kept clean and free of any modifications in order to ensure the proper operation of the system.

  • Page 180: Parking Distance Control

    PARKING DISTANCE CONTROL (1/6) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to This function is an addi-...
  • Page 181 PARKING DISTANCE CONTROL (2/6) Note: in the event of a change in tra- jectory during a manoeuvre, the risk of collision with an obstacle may be sig- nalled late. Operation Note: the display 2 shows the vehicle surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are...
  • Page 182 PARKING DISTANCE CONTROL (3/6) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the dis- play D; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
  • Page 183 PARKING DISTANCE CONTROL (4/6) System sound Enables the system sound to be se- lected from a choice of 3. Deactivating the system sound Activate or deactivate the parking dis- tance control sound. Note: if you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle.
  • Page 184 PARKING DISTANCE CONTROL (5/6) Automatic deactivation of the Operating faults parking distance control When the system detects an operating fault, a beep sounds for approximately The system deactivates: 3 seconds each time reverse gear is se- – when the vehicle speed is above ap- lected and is accompanied by the mes- proximately 6 mph (10 km/h);...
  • Page 185 PARKING DISTANCE CONTROL (6/6) System servicing/repairs – In the event of an impact, the alignment of the sensors may be altered and their operation may consequently be affected. Deactivate the function and consult an authorised dealer. – Any work in the area where the sensors are located (repairs, replacements, etc.) must be carried out by a qualified profes- sional.

  • Page 186: Reversing Camera

    REVERSING CAMERA (1/2) Operation Fixed gauge 3 4 moving guide line: The fixed clearance gauge comprises This is shown in blue on the multime- When the vehicle is reversing, the coloured markers A, B and C, indicat- dia screen 2. It indicates the vehicle tra- camera 1 on the tailgate transmits a ing the distance behind the vehicle: jectory according to the position of the...
  • Page 187 REVERSING CAMERA (2/2) You can also adjust the camera image settings (brightness, contrast, etc.) The screen shows a reverse mirror Activating, deactivating the image. This function is an additional reversing camera The frames are a representation aid. It cannot, therefore, projected onto flat ground;...

  • Page 188: Assisted Parking

    ASSISTED PARKING (1/4) Switching on Special features This function assists with parking ma- noeuvres. With the vehicle at a standstill or driving Ensure that the ultrasonic sensors indi- Take your hands off the steering wheel. at less than approximately 18.6 mph cated by arrows 3 are not obscured (by You only control the pedals and the (30 km/h), press switch 1.
  • Page 189 ASSISTED PARKING (2/4) Choice of manoeuvre Operation Your speed should not exceed around 4 mph (7 km/h). The system can perform four types of Parking  manoeuvres: Once the warning light on the As long as the vehicle speed is less –...
  • Page 190 ASSISTED PARKING (3/4) Your speed should not exceed around In this case, the reason for suspending 4 mph (7 km/h). the manoeuvre will be displayed on the Once in position to exit the space, the multifunction screen. system will notify you of the end of the Make sure: manoeuvre.
  • Page 191 ASSISTED PARKING (4/4) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location.
  • Page 192 AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. In most road conditions you will en- counter, you will not need to touch your lever again: the gears will change au- tomatically at the right time and at the most suitable engine speed because the automatic system takes into ac- count the vehicle load and road contour...

  • Page 193: Automatic Gearbox

    AUTOMATIC TRANSMISSION (2/3) Special cases Special circumstances In certain driving conditions (result- – If the bends and road surface do ing in, for example, engine protection, not allow you to stay in automatic operation of the Electronic Stability mode (e.g. in the mountains), we Control programme: ESC etc.) the au- recommend that you change to tomated system may change the gear...
  • Page 194 AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Maintenance period When the vehicle is stopped, move the Refer to the maintenance document lever to position P while keeping your for your vehicle or consult an Approved foot on the brake pedal: the gearbox is Dealer to check whether the automatic in neutral and the drive wheels are me- gearbox requires scheduled mainte-...
  • Page 195 Section 3: Your comfort Air vents............... Manual air conditioning, heating system .

  • Page 196: Air Vents

    AIR VENTS, air outlets (1/2) 1 left-hand air vent 2 windscreen demisting vents 3 centre air vents 4 side window demister outlets 5 right-hand air vent 6 multifunction screen 7 footwell heater outlets for front pas- sengers 8 footwell heater outlets for rear pas- sengers (depending on the vehicle)
  • Page 197 AIR VENTS, air outlets (2/2) Centre air vents. Side air vents Air flow Air flow Move the control knob 10 (beyond the Move the control knob 11 (beyond the resistance point). resistance point). Upwards: closed. Upwards: closed. Down: maximum air flow. Down: maximum air flow.
  • Page 198 MANUAL AIR CONDITIONING (1/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light on) or off (indicator light off) using the button 7. The air conditioning system is used for: – lowering the temperature inside the passenger compartment;...
  • Page 199 MANUAL AIR CONDITIONING (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 8 to choose the distribution option. The air distribution is displayed on the indicator D. õ The air flow is directed to the windscreen and the front side window demisting vents.
  • Page 200 MANUAL AIR CONDITIONING (3/3) Rear screen de-icing/ demisting With the engine running, press button 6. The operating tell-tale comes This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehi- cles). To exit this function, press button 6 again.

  • Page 201: Automatic Climate Control

    AUTOMATIC CLIMATE CONTROL: control A (1/6) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi- tioning and air temperature.
  • Page 202 AUTOMATIC CLIMATE CONTROL: control A (2/6) Temperature adjustment DUAL function setting The displayed temperature values show a comfort level. Press button 12 to activate. There are two types of settings: When starting the engine, increas- Use the control 2 to adjust the left side –...
  • Page 203 AUTOMATIC CLIMATE CONTROL: control A (3/6) Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press the switch 8 to force activation Preferably, use automatic mode. (the integrated warning light comes on) In automatic mode (warning light 7 or stop the air conditioning (the inte-...
  • Page 204 AUTOMATIC CLIMATE CONTROL: control A (4/6) Clear View function This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
  • Page 205 AUTOMATIC CLIMATE CONTROL: control A (5/6) De-icing or demisting the Rear screen de-icing/ windscreen demisting (depending on the vehicle) Press button 11 – the integrated indi- With the engine running, press the cator light comes on. This function en- button 1 – the integrated indicator will ables rapid demisting or de-icing of the come on.
  • Page 206 AUTOMATIC CLIMATE CONTROL: control A (6/6) Recycling This function is managed automati- cally (operation is confirmed by warn- ing light E), but you can also activate it manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
  • Page 207 AUTOMATIC CLIMATE CONTROL: control B (1/4) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by turning control 3 to increase or reduce the ventilation speed.
  • Page 208 AUTOMATIC CLIMATE CONTROL: control B (2/4) Clear View function Press the 2 button: the integrated indi- cator light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, the door mir- rors (depending on the vehicle) and the heated windscreen (depending on the vehicle).
  • Page 209 AUTOMATIC CLIMATE CONTROL: control B (3/4) Rear screen de-icing/ Switching air conditioning on demisting or off Press the 9 button: the integrated in- In automatic mode, the system switches dicator light comes on. This function the air conditioning system on or off, enables rapid demisting or de-icing of depending on the climate conditions.
  • Page 210 AUTOMATIC CLIMATE CONTROL: control B (4/4) Stopping the system Turn the control 3 to “OFF” to stop the system. To start it, turn control 6 to adjust the fan speed. Air recirculation (isolation of Manual use the passenger compartment) Press the 8 button: the integrated indi- cator light comes on.
  • Page 211 AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations (air conditioning off, You will normally notice an increase in As a general rule, contact your ap- air recirculation activated, ventilation fuel consumption (especially in town) proved dealer in the event of an oper- speed at zero or low etc.), you may when the air conditioning is operating.
  • Page 212 AIR CONDITIONING: information and operating instructions (2/2) Ñ Type of refrigerant fluid  Type of oil in the air condi- tioning circuit  Inflammable product  Consult the driver’s hand- book  Maintenance Quantity of refrigerant fluid present in the ve- x.xxx kg The refrigerant fluid circuit (of which hicle.

  • Page 213: Outside Air Quality And Deodorisation Functions

    OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Air quality Deodorization cycle Deodorisation function With the air conditioning switched on, from the screen A, select Menu, This reduces unpleasant odours in the Vehicle, Take care. passenger compartment. Outside air quality Deodorization cycle –...
  • Page 214 ELECTRIC WINDOWS, FIXED SUNROOF (1/3) These systems operate: – with the engine running; – with the ignition off until one of the front doors is opened (limited to ap- proximately twelve minutes); – with the engine off, front doors closed, after pressing the start button.

  • Page 215: Electric Windows

    ELECTRIC WINDOWS, FIXED SUNROOF (2/3) One-touch mode Note: if the window detects resistance when closing (e.g.: branch of a tree, This mode works in addition to the ope- etc.) it stops and then lowers again by a ration of the electric windows described few centimetres.

  • Page 216: Fixed Glass Roof

    ELECTRIC WINDOWS, FIXED SUNROOF (3/3) Operating faults Driver’s responsibility In case of a fault when closing a window, when parking or stopping the system reverts to normal mode: the vehicle pull the switch concerned up as often Never leave an animal, as necessary to fully close the window child or adult who is not self-suffi- (the window will close gradually), hold...

  • Page 217: Interior Lighting

    INTERIOR LIGHTING (1/2) Map reading lights Note: for vehicles fitted with a naviga- tion system, you can use the multime- Press switch 1 to get: dia screen to deactivate/activate the – permanent lighting; courtesy lights which come on when the doors or boot are opened. To do –...
  • Page 218 INTERIOR LIGHTING (2/2) Glove box light Central console lights Boot lights Light 2 comes on when the cover is The light 3 comes on when the engine The lights 4 come on when the boot lid opened. is started. is opened. 3.24...

  • Page 219: Passenger Compartment Storage, Fittings

    PASSENGER COMPARTMENT STORAGE, FITTINGS (1/5) Front door storage pockets 1 Front sun visor Centre console storage compartment 5 They can hold a 1.5-litre bottle. Lower sun visor 2. Sun visor storage 3 This can be used for storing motorway tickets, cards, etc. Courtesy mirrors Nothing should be placed Ensure that no hard, heavy...
  • Page 220 PASSENGER COMPARTMENT STORAGE, FITTINGS (2/5) Cup holders 6 Front central elbow rest 7 (depending on the vehicle) This can be used for storing a mobile ashtray, cup holder, etc. To move the centre console forwards or backwards (movement A), press This storage compartment has two re- button 8 and slide the console.
  • Page 221 PASSENGER COMPARTMENT STORAGE, FITTINGS (3/5) Glovebox Grab handle 11 Clothes hooks 12 To open the glovebox, lift the catch 10. This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
  • Page 222 PASSENGER COMPARTMENT STORAGE, FITTINGS (4/5) Storage 13 Front seat storage pockets 14 3.28...
  • Page 223 PASSENGER COMPARTMENT STORAGE, FITTINGS (5/5) Rear armrest with cup holder Rear door storage compartment 16 Lower armrest 15. When turning corners, accelerating or braking, Ensure that no hard, heavy ensure that the recepta- or pointed objects are cle being held by the cup placed in the “open”...

  • Page 224: Ashtray, Cigarette Lighter

    ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET Ashtray 1 Accessories sockets 2 To open, lift the cover. To empty, pull the They are provided for connecting ac- ashtray towards you and it will be re- cessories approved by our Technical leased from its housing. Department.

  • Page 225: Rear Headrests

    REAR HEAD RESTS Centre seat headrest storage To refit a headrest The headrests 2 on the rear side seats cannot be adjusted. position Insert the rods in the holes, press the button A and lower the headrest. Check Press the button A and lower the cen- Position for using the central that it is correctly locked in place.
  • Page 226 REAR BENCH SEAT (1/2) To manually fold down the To replace the seatback, proceed in The configuration of the the reverse order to removal. seatbacks two-seat bench with the Refit the seatback and click it back into Ensure that the front seats are far small seatback B pulled place.
  • Page 227 REAR BENCH SEAT (2/2) To automatically fold down Use restriction Conditions of use the seatbacks (flat position) – Vehicle stationary; It is forbidden to drive with a seatback – boot lid open; or a front seat folded down when there From the boot, pulling the control 3 en- –...
  • Page 228 BOOT To open Opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: To close – access the luggage compartment by Lower the tailgate using the handles 2 tilting the rear bench seatback(s), inside the tailgate to help you.

  • Page 229: Luggage Compartment

    LUGGAGE COMPARTMENT COVER To remove the flexible Refitting the luggage section of the luggage cover compartment cover Pull then lift the hook 3 gently. Position the side 1 of the luggage com- partment cover in its housing, press the Guide the luggage cover onto the side 1 and position the opposite side roller 2.
  • Page 230 BOOT FITTINGS (1/2) Mobile floor 1 Intermediate position Storage position (depending on the vehicle) This enables you to compartmentalise This allows for more space to store the boot into two separate spaces. things in the boot. It is made up of two independent and interchangeable parts, A and B.
  • Page 231 BOOT FITTINGS (2/2) Bag hooks 4 Anchorage points Maximum weight per hook: 5 kg. Attachment points 5 If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer. 3.37...

  • Page 232: Transporting Objects In The Luggage Compartment

    TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, the mobile floor in the flat-floor position (exam- ple B).

  • Page 233: Transporting Objects

    TRANSPORTING OBJECTS towbar Maximum dimension A: 1036 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Any towing device must not ob- struct any lighting component or Choice and fitting of towing the number plate when not in use.

  • Page 234: Luggage Net

    LUGGAGE NET (1/2) Fitting the luggage net Depending on the vehicle, this may be – attach the two hooks 5 of the net used when transporting animals or lug- straps 3 on the anchoring points 4 behind the front seats gage to isolate them from the passen- located under the carpet;...
  • Page 235 LUGGAGE NET (2/2) Fitting the luggage net – fix the net belt hook 9 onto the an- choring points 10; behind the rear seats – adjust net strap 8 so that it is taut. Inside the vehicle on each side: The seatbacks must not touch the –...

  • Page 236: Roof Bars

    ROOF BARS, SPOILER (1/2) Accessing the mounting points Vehicles not fitted with longitudinal roof bars Open the doors to access the mount- ing points 1. The attachment of any car- rying device (bike rack, lug- If original roof bars, ap- gage box etc.) resting on proved by our Technical the luggage compartment...

  • Page 237: Spoiler

    ROOF BARS, SPOILER (2/2) Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.

  • Page 238: Multimedia Equipment

    MULTIMEDIA EQUIPMENT Multimedia systems Hands-free telephone integrated control 1 Multimedia screen; 2 Multimedia sockets; For equipped vehicles, use the steering 3 Steering column controls; wheel controls 4. 4 Steering wheel controls; 5 Microphone. Using the telephone We remind you of the need to conform to the legislation in force concerning the use Refer to the equipment instructions...
  • Page 239 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .

  • Page 240: Bonnet

    BONNET (1/2) Unlocking the bonnet catch Opening the bonnet To open, press the control 1. To open, raise the bonnet slightly, then Lift the bonnet up and release the stay 4 lift the paddle 2 at the centre point of from its holder 5.
  • Page 241 BONNET (2/2) After carrying out any work in the engine compart- ment, check that nothing has been left behind (cloth, tools, etc.). These may damage the engine or cause a fire. Closing the bonnet Before closing the bonnet, make sure that nothing has been left in the engine compartment.

  • Page 242: Engine Oil Level: General Information

    ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Dealer if more than 0.5 litres is being Adding engine oil.
  • Page 243 ENGINE OIL LEVEL: general information (2/2) – Remove the dipstick and wipe with a clean, lint-free cloth; – push the dipstick in as far as it will go (for vehicles equipped with a cap- type dipstick C, screw the cap in as far as it will go);...

  • Page 244: Engine Oil Level: Topping Up, Filling

    ENGINE OIL LEVEL: topping up, filling (1/3) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the The vehicle must be parked on level capacity between the “MINI” and ground and the engine should be “MAXI”...
  • Page 245 ENGINE OIL LEVEL: topping up, filling (2/3) Adding engine oil. Use a funnel or protect the filling neck area to avoid engine oil escaping onto a hot part of the engine compartment or a sensitive part (e.g. electrical Before performing any components).

  • Page 246: Oil Change

    ENGINE OIL LEVEL: topping up, filling OIL CHANGE (3/3)/ Oil change Engine oil grade Service interval: refer Refer to the maintenance document for Maintenance Service Booklet for your your vehicle. vehicle. Filling and/or checking the oil level: when topping Oil change capacity up or checking the oil level, Please refer to the maintenance docu- ensure that no oil leaks onto...

  • Page 247: Levels

    LEVELS, FILTERS (1/3) Top this level up when cold before it Replacement interval reaches the “MINI” mark. Refer to the Maintenance Document for Frequency of checking coolant level your vehicle. Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant).

  • Page 248: Brake Fluid

    LEVELS, FILTERS (2/3) Level 3 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net-...

  • Page 249: Windscreen Washer Reservoir

    LEVELS, FILTERS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle. Before performing any action in the engine com- Liquid...

  • Page 250: Tyre Pressure

    TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure monitoring system In cases of under-inflation (puncture,  low pressure, etc.), warning light lights up on the instrument panel. Please refer to the information on the “Tyre pressure monitoring system” in Section 2.
  • Page 251 TYRE PRESSURES (2/2) Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile...

  • Page 252: Battery

    BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. The message will go off. The charge status of your battery can decrease especially if you use your ve- hicle:...
  • Page 253 BATTERY (2/2) Replacing the battery For your safety and the proper operation of the ve- hicle’s electrical equipment (lights, windscreen wipers, braking assistance, etc.), any work on the battery (removal, disconnec- tion, etc. ) must be carried out by a specialist professional.

  • Page 254: Bodywork Maintenance

    BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
  • Page 255 BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or Degrease or clean using freezing temperatures. high-pressure cleaning equipment or by spray- Do not scrape off mud or dirt without ing on products not ap- pre-wetting.
  • Page 256 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning the headlights, finish sensors and cameras Return the windscreen wiper stalk to the Park position (refer to the informa- This type of paint requires certain pre- Use a soft cloth or cotton wool.

  • Page 257: Interior Trim Maintenance

    INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display etc.) larly.
  • Page 258 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in Position objects such as deodorants, the vehicle scents etc. near air vents as this could damage your dashboard trim. If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv-...
  • Page 259 Section 5: Practical advice Puncture, emergency spare wheel ..........Tyre inflation kit .

  • Page 260: Puncture, Emergency Spare Wheel

    PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emer- gency spare wheel disappears from the instrument panel display).
  • Page 261 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) Emergency spare wheel A Emergency spare wheel B Note: Store the punctured wheel in the storage bag provided, along with the To get to it: Vehicle fitted with a subwoofer tool kit and put them in the boot. below the luggage compartment –...

  • Page 262: Tyre Inflation Kit

    TYRE INFLATION KIT (1/4) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 263 TYRE INFLATION KIT (2/4) With the engine running and the If the recommended pressure of 1.8 parking brake applied, bar cannot be achieved after 10 min- utes, repair is impossible. Do not – Disconnect any accessories from the drive the vehicle. Consult an author- vehicle’s accessories sockets;...
  • Page 264 TYRE PRESSURE KIT (3/4) Precautions when using the – Start immediately and drive at be- tween 12 and 37 mph (20 and 60 km/h) in order to distribute the The kit should not be operated for more product evenly in the tyre; after driv- than 10 consecutive minutes.
  • Page 265 TYRE INFLATION KIT (4/4) Please be aware that a poorly tightened or miss- ing valve cap can make the tyres less airtight and may lead to pressure loss. Always use valve caps identical to those fitted originally and tighten them fully. Following repair with the kit, do not travel further than 120 miles (200 km).

  • Page 266: Tools

    TOOLS Jack 2 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned). Lever 3 This tightens or releases the tow eye 5. Hubcap tool 4 This tool is used to remove the wheel trims.

  • Page 267: Wheel Trims - Wheel

    WHEEL TRIMS - WHEEL Remove the wheel trim using hubcap tool 1 (located in the tool kit) by en- gaging the hook in the opening near valve 2. To refit it, align it with valve 2. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the valve.

  • Page 268: Changing A Wheel

    CHANGING A WHEEL (1/2) Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and aligned with the jack head). Vehicles equipped with a jack and wheelbrace Switch on the hazard warn- If necessary, remove the wheel trim.
  • Page 269 CHANGING A WHEEL (2/2) Turn it a few times to lift the wheel off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.

  • Page 270: Tyres (Tyre And Wheel Safety, Use In Winter)

    TYRES (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essen- wear warning strips, these strips will become visible 2: it is then necessary tial to keep them in good condition. to replace your tyres because the tread You must make sure that your tyres rubber is now only 1.6 mm deep at...
  • Page 271 TYRES (2/3) Tyre pressures The pressures should be checked cold: Vehicle fitted with a tyre pressure ignore higher pressures which may be monitoring system Adhere to the tyre pressures (including reached in hot weather or following a In cases of under-inflation (puncture, the emergency spare wheel).
  • Page 272 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- chains to the rear axle is strictly for- sary to observe the speed specified by bidden.
  • Page 273 FRONT HEADLIGHTS: changing bulbs (1/3) After replacing the bulbs, you must put the air duct A back into position. To do this, perform the above operation in re- verse. Accessing the bulbs On the right-hand side of the vehicle, you will need to remove the filler neck 4 On the left-hand side of the vehicle, for the windscreen washer tank to you will need to remove the air duct A...
  • Page 274 FRONT HEADLIGHTS: changing bulbs (2/3) Halogen main beam headlight To change the bulb: – remove cover C; – turn the bulb holder a quarter turn 7; – remove the bulb. Bulb type: H7. It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights.

  • Page 275: Headlights (Changing Bulbs)

    FRONT HEADLIGHTS: changing bulbs (3/3) Halogen front fog lights 10 Additional lights The front bumper needs to be removed; If you wish to fit fog lights to your ve- consult an approved Dealer. hicle, please see an authorised dealer. Type of bulb: H11. LED front fog lights 10 Consult an approved dealer.
  • Page 276 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (1/2) Side lights and brake lights 1 High level brake light 3 Consult an approved Dealer. Consult an approved dealer. LED direction indicators 2 Rear fog lights and reversing lights 4 Consult an approved Dealer. Consult an approved Dealer.

  • Page 277: Rear Lights And Side Lights (Replacing Bulbs)

    REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (2/2) Number plate lights 5 Indicator lights 6 – Unclip the light 5 (using a tool such The wing mirror needs to be removed; as a flat-blade screwdriver). consult an authorised dealer. –...

  • Page 278: Interior Lighting: Changing Bulbs

    INTERIOR LIGHTING: changing bulbs (1/2) Map reading lights 1 Lights 2 Glove box light 4 (depending on vehicle) Please consult an authorised dealer. Please consult an authorised dealer. Consult an approved dealer. Lights 3 (depending on vehicle) Please consult an authorised dealer. 5.20...
  • Page 279 INTERIOR LIGHTING: changing bulbs (2/2) Boot lights 5 Central console lights 6 (depending on vehicle) Please consult an authorised dealer. Please consult an authorised dealer. 5.21...

  • Page 280: Card: Battery

    CARD: battery (1/2) The batteries are available from ap- proved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical con- tact. Replacing the battery – replace it according to the direc- If they need to be replaced, tion and template shown inside the When the message “Keycard battery...
  • Page 281 CARD: battery (2/2) Operating faults If the battery is too weak to ensure cor- rect operation, you can still start and lock/unlock the vehicle (please refer to the information on “Locking/unlocking the opening elements” in Section 1). Precautions relating to batteries: –...

  • Page 282: Radio Frequency Remote Control: Batteries

    RADIO FREQUENCY REMOTE CONTROL: batteries (1/2) The batteries are available from ap- proved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electri- cal contact. Replacing the battery Note: It is not advisable to touch the electronic circuit in the key cover when If they need to be replaced,...
  • Page 283 RADIO FREQUENCY REMOTE CONTROL: batteries (2/2) Operating faults If the battery is too weak to ensure cor- rect operation, you can still start and lock/unlock the vehicle (please refer to the information on “Locking/unlocking the doors” in Section 1). Precautions relating to batteries: –...

  • Page 284: Fuses

    FUSES (1/3) If any electrical component does not Fuses in passenger compartment C work, check the condition of the fuses. on the right-hand side of the vehicle Unclip the cover C using a screwdriver Fuses in passenger compartment or similar. A or B on the left-hand side of the vehicle Unclip the cover A using a screwdriver...
  • Page 285 FUSES (2/3) Use the fuse allocation label in the stor- age compartment A, B or C to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label.

  • Page 286: Wipers (Replacing Blades)

    FUSES (3/3) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation  Indicators Steering column controls ß ñ Brake light Heated seats  Audio amplifier Heated rear screen  Door locking/unlocking Electric door mirror ë...
  • Page 287 BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
  • Page 288 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
  • Page 289 ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
  • Page 290 WINDSCREEN WIPER BLADES: replacement (1/2) Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked in place. Lower the windscreen wiper arm carefully. With the ignition on, return the wind- screen wiper stalk to the stop position. NB: Before restarting your vehicle, lower the windscreen wiper blades onto the windscreen to avoid any risk...
  • Page 291 WINDSCREEN WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; –...
  • Page 292 TOWING: breakdown recovery (1/2) Before towing, put the gearbox in neu- The speed specified by current legis- tral, unlock the steering column and re- lation for towing must always be ob- lease the parking brake. served. If your vehicle is the towing For vehicles fitted with an automatic vehicle, do not exceed the maximum gearbox, if it is not possible to put the...
  • Page 293 TOWING: breakdown recovery (2/2) Ensure that the towing eye is bolted correctly. Risk of losing the towed object. – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake.

  • Page 294: Operating Faults

    OPERATING FAULTS (1/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the card POSSIBLE CAUSES WHAT TO DO The card does not lock or unlock Card battery is flat.
  • Page 295 OPERATING FAULTS (2/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the card POSSIBLE CAUSES WHAT TO DO Desynchronisation of the card. Unlock the driver’s door by inserting the key in- tegrated into the card into the door lock (see the paragraphs on “Locking, unlocking the...
  • Page 296 OPERATING FAULTS (3/8) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
  • Page 297 OPERATING FAULTS (4/8) The starter is activated POSSIBLE CAUSES ACTION REQUIRED The instrument panel indicator lights are Battery terminals not tight, bat- Retighten or reconnect the terminals, or clean them if weak or fail to light up and the starter tery terminals disconnected or they are oxidised.
  • Page 298 OPERATING FAULTS (5/8) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
  • Page 299 OPERATING FAULTS (6/8) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force on the steering wheel Fault with the electric assistance needed to turn the wheels. Consult an ap- motor.
  • Page 300 OPERATING FAULTS (7/8) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information on “Fuses”...
  • Page 301 OPERATING FAULTS (8/8) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the head- Traces of condensation may be a nat- lights or rear lights. ural phenomenon caused by varia- tions in temperature and humidity. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor...
  • Page 302 5.44...
  • Page 303 Section 6: Technical specifications Vehicle identification plate ............Technical Information for the emergency services .

  • Page 304: Vehicle Identification Plate

    VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MAM (Maximum Authorised hicle identification plate should be Mass). quoted on all correspondence or 5 GTW (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MPAW (Maximim Permissible The presence and location of the in- Weight) for front axle.

  • Page 305: Technical Information For The Emergency Services

    TECHNICAL INFORMATION FOR THE EMERGENCY SERVICES The QR Code on the A label allows emergency workers using a tablet or smartphone to immediately access the technical information useful for working on the vehicle in the event of an acci- dent. Ensure that the A label is always visible and present on the windscreen as well as the rear screen.

  • Page 306: Engine Identification

    ENGINE IDENTIFICATION (1/2) Please quote the engine identifica- tion information in area A in all cor- respondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine serial number.
  • Page 307 ENGINE IDENTIFICATION (2/2) Please quote the engine identifica- tion information in area A in all cor- respondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine serial number.

  • Page 308: Dimensions

    DIMENSIONS (in metres) 0,913 2,647 0,930 1,556 4,489 1,611-1,623* 1,542 2,058 * Unladen, with or without longitudinal roof bar...

  • Page 309: Engine Specifications

    ENGINE SPECIFICATIONS (1/3) Versions 1.2 Tce 1.3 Tce 1.6 Tce 1.5 dCi 1.6 dCi 1.7 dCi Engine type H5F Turbo H5H Turbo M5M Turbo (see engine plate) Cubic capacity (cc) 1 197 1 333 1 618 1 461 1 598 1 749 Type of fuel Petrol...
  • Page 310 ENGINE SPECIFICATIONS (2/3) Versions 1.2 Tce 1.3 Tce 1.6 Tce 1.5 dCi 1.6 dCi 1.7 dCi Engine type H5F Turbo H5H Turbo M5M Turbo (see engine plate) Cubic capacity (cc) 1 197 1 333 1 618 1 461 1 598 1 749 Fuel types...
  • Page 311 ENGINE SPECIFICATIONS (3/3) Versions 1.2 Tce 1.3 Tce 1.6 Tce 1.5 dCi 1.6 dCi 1.7 dCi Engine type H5F Turbo H5H Turbo M5M Turbo (see engine plate) Cubic capacity (cc) 1 197 1 333 1 618 1 461 1 598 1 749 Spark plugs Only use the spark plugs specified for your vehi-...

  • Page 312: Weights

    WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Maximum permissible all-up weight (MMTA) the information on “Vehicle identification plates”...

  • Page 313: Replacement Parts And Repairs

    REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.

  • Page 314: Service Sheets

    SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 315 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 316 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 317 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 318 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 319 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...

  • Page 320: Anticorrosion Check

    ANTICORROSION CHECK (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
  • Page 321 ANTICORROSION CHECK (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
  • Page 322 ANTICORROSION CHECK (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
  • Page 323 ANTICORROSION CHECK (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.21...
  • Page 324 ANTICORROSION CHECK (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.22...
  • Page 325 ANTICORROSION CHECK (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Stamp Repair to be carried out: Date of repair: Repair to be carried out: Stamp Date of repair: 6.23...
  • Page 326 6.24...
  • Page 327 ALPHABETICAL INDEX (1/6) automatic locking of the doors while driving ...... 1.19 4 wheel drive (4WD) ..........2.42 → 2.45 battery ABS ..............1.60, 2.32 → 2.37 breakdown recovery ......... 5.29 – 5.30 accessories................ 5.31 battery..........4.14 – 4.15, 5.29 – 5.30 accessories socket ...........
  • Page 328 ALPHABETICAL INDEX (2/6) control instruments ........1.58 → 1.67, 1.81 electric windows ............3.20 → 3.22 controls electronic parking brake ........2.17 → 2.21 steering wheel .............. 3.44 electronic stability control: ESC ......2.32 → 2.37 controls ..............1.54 → 1.57 emergency active braking........2.38 → 2.41 courtesy light ..........
  • Page 329 ALPHABETICAL INDEX (3/6) fittings ..............3.25 → 3.29 heated windscreen ..........3.7 → 3.16 fixed sunroof ..............3.22 heating and air conditioning system ......3.4 → 3.17 freewheel ................2.24 heating system ............3.4 → 3.16 front seat adjustment ..........1.21 – 1.22 Hill Start Assist............2.32 → 2.37 front seats hooks adjustment ..........
  • Page 330 ALPHABETICAL INDEX (4/6) coolant ................4.9 multimedia (equipment) ............. 3.44 windscreen washer reservoir ........4.11 multimedia equipment ............3.44 lifting the vehicle changing a wheel ..........5.10 – 5.11 navigation ................3.44 lighting: navigation system .............. 3.44 exterior .............1.82 → 1.89 instrument panel ............
  • Page 331 ALPHABETICAL INDEX (5/6) reagent (tank) ..........1.101 → 1.104 screens reagent quality ...........1.101 → 1.104 multimedia screen ........2.76 – 2.77, 3.44 seat belt pretensioners reagent tank............1.101 → 1.104 reagent tank cap ..........1.101 → 1.104 front seat belt ...........1.29 → 1.34 reagent tank capacity ........1.101 →...
  • Page 332 ALPHABETICAL INDEX (6/6) tool kit .................. 5.8 wheelbrace ................5.8 towing wheels (safety) ............5.12 → 5.14 breakdown ............5.34 – 5.35 windscreen de-icing/demisting ........3.7 → 3.16 towing equipment ............3.39 windscreen washer ....1.90 → 1.95, 1.94, 1.96 – 1.97 towing a caravan ............3.39, 6.10 windscreen washer/wiper ........
  • Page 334 à999105131Sï ë ò ä VA RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents