Advertisement

Quick Links

Copyright Information
Copyright © 2021 by SHENZHEN SMARTSAFE TECH CO., LTD. (Hereinafter refer to
"SmartSafe"). All rights reserved. No part of this publication may be reproduced, stored
in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying and recording or otherwise, without the prior written permission.
Statement: SmartSafe owns the complete intellectual property rights for the software
used by this product. For any reverse engineering or cracking actions against the
software, SmartSafe will block the use of this product and reserve the right to pursue its
legal liabilities.
Disclaimer of Warranties and Limitation of Liabilities
All information, illustrations, and specifications in this manual are based on the latest
information available at the time of publication.
The right is reserved to make changes at any time without notice. We shall not be liable
for any direct, special, incidental, indirect damages or any economic consequential
damages (including the loss of profits) due to the use of the document.
Important Safety Precautions
To avoid personal injury, property damage, or accidental damage to the product, read
all of the information in this section before using the tool.
DANGER
 When an engine is operating, keep the service area well-ventilated or attach a
building exhaust removal system to the engine exhaust system. Engines produce
various poisonous compounds (hydrocarbon, carbon monoxide, nitrogen oxides, etc.)
that cause slower reaction time and result in death or serious personal injury.
 Please use the included battery and power adaptor. Risk of explosion if the battery
is replaced with an incorrect type.
 DO NOT attempt to operate the tool while driving the vehicle. Have a second person
to operate the tool. Any distraction may cause an accident.
WARNING
 Always perform automotive testing in a safe environment.
 Do not connect or disconnect any test equipment while the engine is running.
 Before starting the engine, put the gear lever in the Neutral position (for manual
transmission) or in the Park (for automatic transmission) position to avoid injury.
 NEVER smoke or allow a spark or flame in vicinity of battery or engine. Do not
operate the tool in explosive atmospheres, such as in the presence of flammable
liquids, gases, or heavy dust.
 Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
iSmartIMMO 801 User Manual
l
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iSmartIMMO 801 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SmartSafe iSmartIMMO 801

  • Page 1 Statement: SmartSafe owns the complete intellectual property rights for the software used by this product. For any reverse engineering or cracking actions against the software, SmartSafe will block the use of this product and reserve the right to pursue its legal liabilities.
  • Page 2 801 User Manual  Wear an ANSI-approved eye shield when testing or repairing vehicles.  Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.  Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs.
  • Page 3: Table Of Contents

    801 User Manual Table of Contents 1 Packing List........................1 2 Overview..........................2 2.1 Introduction........................2 2.2 Display Tablet........................3 2.3 VCI Dongle........................4 2.4 iSmartIMMO G3......................4 3 Initial Use.........................5 3.1 Charging........................5 3.2 Power On & Off......................6 3.3 Basic Operations......................6 3.4 Change System Language..................
  • Page 5: Packing List

    801 User Manual 1 Packing List The following accessory items are only for reference. Please consult from the local agency or check the package list supplied with this tool together. Item Descriptions iSmartIMMO 801 Main Unit VCI dongle iSmartIMMO G3...
  • Page 6: Overview

    801 User Manual After removing the vehicle dashboard, connect INS Cable V2 programmer, vehicle dashboard, and the cable. MCU Cable V1 To connect the programmer and MCU. Connect the programmer and the engine to read Bench Mode engine or gearbox ECU (Connect engine ECU with...
  • Page 7: Display Tablet

    801 User Manual 2.2 Display Tablet Docking slot for VCI dongle - for housing the VCI dongle. 2. VCI dongle - It is pre-installed in the docking slot on the top of the display tablet. Use the hand to press the dongle once, it will be automatically ejected from the docking slot.
  • Page 8: Vci Dongle

    801 User Manual 2.3 VCI Dongle This dongle works as a VCI (Vehicle Communication Interface) device. It is used to obtain the vehicle data, and then send it to the tablet for analysis via Bluetooth. 1. OBD-16 diagnostic connector - Connects the OBD-II extension cable or directly plug into the vehicle's DLC (Data Link Connector) port.
  • Page 9: Initial Use

    801 User Manual 1. DB26 diagnostic connector - Connects with the Mercedes Benz infrared collector, ECU cable and MCU cable etc. 2. Mercedes Benz infrared key slot - Holds the Mercedes Benz key. 3. Vehicle key slot - Holds the car key for RF defection.
  • Page 10: Power On & Off

    801 User Manual adapter. 2. Connect the other end to the charging port on the bottom of the host. 3. Plug the charger power plug into a power outlet to start charging. Caution: Please use the included power adaptor to charge your tool. No responsibility can be assumed for any damage or loss caused as a result of using power adaptors other than the one supplied.
  • Page 11: Set Standby Time

    801 User Manual less LANs. 3. Select the desired WLAN network from the list. If the chosen network is open, you can connect directly. A password may be required for secured networks. Note: Once WLAN is set as ON, the tablet will consume more power. While it keeps unused, please set it off to save power.
  • Page 12: Getting Started

    801 User Manual B.If you have registered to be a member, input your name and password, and then tap Login to enter the main menu screen directly. Note: The tablet has an auto-save function. Once the username and password are correctly entered, the system will automatically store them.
  • Page 13: Communication Setup

    801 User Manual side for most vehicles. For some vehicles with special designs, the DLC location may vary. If the DLC cannot be found, refer to the vehicle’s service manual for the location. Vehicle Connection 4.2.2 Follow the steps mentioned below to connect OBD II vehicle: Locate the vehicle’s DLC socket.
  • Page 14 801 User Manual This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. Vehicle connection 5.1.1 1. For most vehicles, just use the included OBD II extension cable to connect the VCI to the vehicle’s DLC port.
  • Page 15 801 User Manual 2. Tap OK. 3. Enter the Anti-Theft System, follow the illustration below to connect the VCI dongle, vehicle and iSmartIMMO G3 to perform the next step. 4. If you don’t know the type of the anti-theft System, tap Intelligent Mode to...
  • Page 16 801 User Manual 5. Tap CAS4/CAS4+ anti-theft System, the following screen will appear: 6. Tap Preprocessing to perform Read anti-theft data, Key matching and more. If it has already been preprocessed, here you can perform the relevant functions. The ECU will be upgraded in this process, and files need to be downloaded online.
  • Page 17 801 User Manual 9. Return to the function menu and tap Key Learning. 10. After the key information successfully read, select the unused key position and tap Key Generated By Ignition Switch. 11. Read and display the password, and tap OK.
  • Page 18 801 User Manual 12. Place a new key close to vehicle coil, tap OK, and wait for the key to generate. 13. After the dealer key is successfully generated, please try to start the vehicle. 14. Now the key matching is finished and the new key is ready for use.
  • Page 19: Immo Programming

    801 User Manual 5.2 IMMO Programming The iSmartIMMO G3 is required when performing this operation. It has the following functions: • Read transponder data (including Mercedes Benz infrared smart key), and generate exclusive keys. • Read/write on-board EEPROM chip data, and read/write MCU/ECU chip data.
  • Page 20 801 User Manual 3. Select the desired item to proceed. EEPROM Programming 5.2.1 This function allows you to read/write on-board EEPROM chip data. Engine Programming 5.2.2 This function allows you to read the engine data and write in the backup data after a new engine is replaced.
  • Page 21 801 User Manual Tap Search For ECU Model. 4. Check ECU model (printed on the sticker on the back of your Engine), enter the engine type in the dialogue box (for example , the engine type should be MED17.7.7) and tap OK.
  • Page 22 801 User Manual 5. Tap OK to confirm the engine type and enter the function selection screen. Note: The function selection screen varies by differentvehicle manufacturers. a. Tap View Wiring Diagram to check how to connect the engine with the iSmartIMMO G3.
  • Page 23 801 User Manual D. BENCH mode cable E. Adaptor cable associated with the BENCH mode cable F. Engine b. Tap Backup EEPROM data to create a file name and save it on the tablet. c. Tap Restore EEPROM data to write the backup EEPROM data into the new engine.
  • Page 24 801 User Manual Situation 1: 1. Tap Gearbox. 2. Select Gearbox type according to the specific model, here we choose DQ200-MQB (take this as an example) to enter the function selection screen. Note: The function selection screen varies by differentvehicle manufacturers.
  • Page 25 801 User Manual D. BENCH mode cable E. Adaptor cable for the BENCH mode cable F. Gearbox ECU 4. Tap Connect to read the chip ID of the original car gearbox. 5. Tap Backup EEPROM Data to read the EEPROM data of the original car gearbox and then enter the new file name to save it on the tablet.
  • Page 26 801 User Manual 10. Tap Restore FLASH Data to write the FLASH data of the original vehicle gearbox backed up in step 6 into the new gearbox ECU. Situation 2: 1. Tap Gearbox. 2. Select Gearbox type according to the specific model, here we choose DQ200-...
  • Page 27 801 User Manual Note: The function selection screen varies by differentvehicle manufacturers. 3. Tap View Writing Diagram to view how to connect the original car gearbox ECU with iSmartIMMO G3 using the BENCH mode cable and its associated adaptor cable.
  • Page 28 801 User Manual 7. Tap Anti-theft Matching, choose VW to enter the anti-theft system, select MQB Instrument -> Replacement Of Parts -> Transmission, tap OK.
  • Page 29 801 User Manual 8. Tap YES to enter the gearbox replacement screen.
  • Page 30 801 User Manual 9. When replacing the transmission ECU, two groups of anti-theft data are required: • Anti-theft data of transmission engine (backed up in step 5) • Anti-theft data of the target vehicle 1). Select Edit1, tap NO, tap Obtain From EEPROM Data, select the new gearbox EEPROM data backed up in step 5, and tap OK.
  • Page 31 801 User Manual Note: If there is no anti-theft data of the target vehicle, select Original Vehicle Key Obtained, put the original vehicle key in the iSmartIMMO G3, and just follow the prompts to obtain it, no need to enter any data to complete the replacement.
  • Page 32: Diagnose

    801 User Manual Note: If Original Vehicle Key Obtained is selected in step 8, the vehicle’s VIN code, power level and CS code in this step will be automatically obtained. The user is not required to enter any data to complete the replacement.
  • Page 33: Manual Selection

    801 User Manual Camera Scan: This mode allows you to identify the vehicle model via scanning the vehicle’s VIN. Once scanning is complete, the tablet will enter the diagnostic software of the vehicle directly. Enter VIN: In this mode, input the VIN manually to enter the diagnostic software of the vehicle.
  • Page 34 801 User Manual Systems with fault codes are displayed in red. Systems functioning normally are displayed in black. Explanation of terms: Report: Tap to save the diagnostic result as a diagnostic report in text format. Help: Tap to view the help information of the selected DTC.
  • Page 35 801 User Manual This function displays the detailed information of DTC records retrieved from the vehicle’s control system. Tap Read Fault Code on the test function selection screen, the screen will display the diagnostic result. Explanation of terms: Freeze Frame: A snapshot of critical parameter values at the time the DTC is set.
  • Page 36 801 User Manual Notes: Tap to set the display style. indicates sticky top. B indicates this item will be displayed in Bold. A indicates this item will be displayed in Red. There are 3 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way.
  • Page 37: Reset

    801 User Manual F. Special Function In addition to amazing & powerful diagnostic function, the tool also features various reset functions, which varies from vehicle to vehicle. Reset This module provides an easy dial to quickly access the most commonly performed service functions as following.
  • Page 38 801 User Manual the accurate angle for left and right steering. After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body, you must reset the steering angle.
  • Page 39 801 User Manual confirmed or re-coded so that the cylinder can better identify injectors to accurately control fuel injection. 7.9 Battery Maintenance System Reset This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.
  • Page 40 801 User Manual the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture. 7.14 Sunroof Initialization This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc.
  • Page 41: Update

    801 User Manual NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU.
  • Page 42: Personal Center

    801 User Manual Tap Feedback, and tap OK to enter into the vehicle diagnostic record page. A. Feedback Tap the target vehicle to enter the feedback page. B. History Tap it to view the diagnostic feedback logs which are marked with different color indicating the process status of the diagnostic feedback.
  • Page 43 801 User Manual Input the IP address of the printer, and add the printer. 6. Choose the printer, and click the icon to printing the report.
  • Page 44 801 User Manual 10.1.2 Print via PC Paste reports to the PC: In the Job Menu, tap Others - Personal Center - Settings - Mode Switch, and select “DEVICE MODEL”. 2. Connect the device to the PC via USB cable (Type A to Type C).
  • Page 45 801 User Manual This item is used to record the data stream. 10.6 Subscription Renewal Card This item is used to check the status of the subscription renewal card. 10.7 Profile Use this item to view and configure personal information.
  • Page 46 The exclusive remedy for any automotive meter found to be defective is repair or replacement, and SmartSafe shall not be liable for any consequential or incidental damages.
  • Page 47 801 User Manual FCC Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
  • Page 48 être utilisé dans des conditions d ‘exposition portables illimitées. Statement: SmartSafe reserves the rights to make any change to product designs and specifications without notice. The actual object may differ a little from the descriptions in the manual in physical appearance, color and configuration. We...

Table of Contents