Advertisement

Quick Links

Copyright
Copyright © 2021 by SHENZHEN SMARTSAFE TECH CO.,LTD. All rights
reserved. No part of this publication may be reproduced, stored, or transmitted
in any form without the written permission of the copyright owner.
Trademark
is a registered trademark of SHENZHEN SMARTSAFE TECH CO.,
LTD. in China and other countries. All other marks are trademarks or registered
trademarks of their respective owners.
Disclaimer
The contents of this document are subject to changes without notice due to
continued improvements in design, manufacture, and methodologies.SmartSafe
is not liable for the damage or losses due to the use of this document.
FCC Warnning:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
I

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iSmartIMMO G3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SmartSafe iSmartIMMO G3

  • Page 1 Copyright Copyright © 2021 by SHENZHEN SMARTSAFE TECH CO.,LTD. All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form without the written permission of the copyright owner. Trademark is a registered trademark of SHENZHEN SMARTSAFE TECH CO., LTD.
  • Page 2 -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. ISED Warnning: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
  • Page 3 Important: Please read this manual carefully and understand the safety precautions before performing any operation to this product. Safety Grades Symbol Usage Indicates a hazardous situation which, if not Danger avoided, will result in death or serious injury to the operator or to bystanders.
  • Page 4 • Use the included battery and charger. Risk of explosion if the battery is replaced with an incorrect type. • Do not disconnect power abruptly when the test equipment is being formatted or in process of uploading or downloading. Or else it may result in program error.
  • Page 5: Table Of Contents

    Table of Contents 1 About this Manual ...................1 1.1 Target Reader ..................1 1.2 Typographic Conventions ..............1 1.3 Symbols ....................1 2 About iSmartIMMO G3 ..................2 2.1 Product Overview ................2 2.2 Power Source ..................3 ...............4 2.4 Accessories ..................4 3 Diagnostics .....................4 3.1 Common Operations ................4 3.1.1 Establish Hardware Connection ............4...
  • Page 6: About This Manual

    1 About this Manual This manual introduces the basic information of iSmartIMMO G3 and instruction on the product usage. iSmartIMMO G3 is a powerful anti-theft solution and an ideal choice for professional repair shops and vehicle maintenance businesses. It has achieved vehicle key, Engine and gearbox programming, featuring powerful multiple parts reprogramming and wide range of vehicle coverage.
  • Page 7: About Ismartimmo G3

    2 About iSmartIMMO G3 2.1 Product Overview...
  • Page 8 Part Name Description To connect with all anti-theft DB26 diagnostic connector cables. Benz key slot To place Benz car key. To place car key for RF Key slot defection. Key chip slot To place key chip. • Red light indicates faults. Power indicator •...
  • Page 9: Power Source

    2.3 Power Source The product does not have an independent power supply, you can power it up via either of the followings ways: • Use the included power adaptor • Connect the device through the vehicle’s DLC 2.4 Accessories Photo Accessory Name Descrption To connect vehicle DLC port,...
  • Page 10 Connect the programmer and the engine to read engine or BENCH mode gearbox ECU (Connect engine cable ECU with the BENCH mode cable based on BENCH mode diagram). Connect the programmer MCU Converter with MCU(chip soldering is required in this procedure). Connect the programmer MCU Converter with MCU(chip soldering is...
  • Page 11 MCU cable with To connect the programmer multiple leads and MCU.
  • Page 12: Diagnostics

    3 Diagnostics iSmartIMMO G3 diagnostic function supports key programming, engine and gearbox replacement for various of vehicles, you can retrieve ECU information, read, erase, and write in for a range of chips as shown in the product options. 3.1 Common Operations •...
  • Page 13: Establish Wireless Connection

    1. Slide down the status bar from the top. , go to Wireless and network -> Bluetooth. 2. Touch 3. Select the iSmartIMMO G3 to be connected, wait until the connection is successful. • 3.1.3 Perform Common Operations You should enter the function interface before using the programmer.
  • Page 14: Diagnostic Operations

    4. Depending on your requirement, touch any of the following options : • Gearbox Learning • Anti-Theft System • Engine System 3.2 Diagnostic Operations • 3.2.1 Key Programming You can use anti-theft system to access key chip programming functions. The product supports reading, retrieving and writing key information, as well as other key-related functions.
  • Page 15 • Operating on key programming You can use key programming function to backup old key data and write in data for new keys. Below procedure shows you how to perform key SmartSafe c i t current key data and new key generation.
  • Page 16 c. Touch Key Operation. d. Touch Key Learning. e. Touch OK after reading the the onscreen instruction.
  • Page 17 f. Touch OK. g. Touch OK to save the key data.
  • Page 18 2. Generate a new key. a. Touch the desired blank key position. b. Place the new key into the programmer key slot and touch OK. YES. d. If the key generation is done, touch OK t...
  • Page 19: Gearbox Programming

    • Operating on gearbox programming Below procedure shows you how to perform gearbox programming for a BMW using SmartSafe diagnostic product, the procedure contains gearbox connection and erasure of gearbox data.
  • Page 20 1. Connecting the gearbox. a. On the programmer function interface, touch EGS System to enter gearbox programming. b. Touch the correct chassis type. c. You will then see a corresponding connection diagram. Touch OK.
  • Page 21 2. Erasing gearbox data. a. Touch EGS Erasure. b. Touch DOWNLOAD. c. Touch OK.
  • Page 22 d. Touch DOWNLOAD. e. Touch OK. f. Touch YES. g. Touch YES.
  • Page 23: Engine Programming

    • Operating on Engine Programming Below procedure shows you how to perform engine programming for a Volkswagen using diagnostic product, the procedure contains chip ID SmartSafe...
  • Page 24 retrieval, engine connection, data backup and data restoration. 1. Retrieve chip ID. a. Touch Engine. b. Select Engine Brand. c. Touch Search for ECU model.
  • Page 25 d. Check ECU model (printed on the sticker on the back of your Engine), enter the engine type in the dialogue box(In example below,the engine type should be MED17.7.7). e. Touch OK.
  • Page 26 2. Connect the engine. a. Touch View Wiring Diagram. b. Read the connection diagram, perform the proper connection based on the engine type and then touch OK. c. Touch Read chip ID.
  • Page 27 d. When below dialogue box appears, touch OK. 3. Backup data. a. Touch Backup EEPROM Data.
  • Page 28 d. Touch OK. is done. 4. Restore EEPROM data. Stop: The EEPROM restoration applies only when you have encountered irrevocable faults.
  • Page 29 a. Touch Restore EEPROM Data. d. When the data is successfully restored, touch OK.
  • Page 30: Software Upgrade

    4. Software Upgrade The software update function keeps your diagnostic software & App up-to- date, you can also use it to customize your frequently used software. To update Diagnostic Software & APP: 1. On the main diagnostic screen, tap Software Update to enter the update center.
  • Page 31 Note: • You may stop the process by tapping Stop, and tap Continue to resume the process later. • In case of network connection failure, tap Retry. 3. You will see below dialogue box once the installation is completed.
  • Page 32: Warranty

    SmartSafe automotive meters, except as stated herein. The exclusive remedy for all automotive meters found to be defective is to repair or replace, and SmartSafe has no liability for any consequential or incidental damages. The following cases are not covered in product warranty: •...

Table of Contents