Operating Your Ceiling Fan - Hunter Ceiling Fans Installation And Operation Manual

10 10 10 10 10
installing without the light fixture
Your Hunter fan comes with an integrated light fixture assembly
and an optional switch housing cap and plug button. This feature
gives you the option of installing the fan with or without the in-
cluded light fixture.
attaching the upper switch housing
1. Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 26.
2. Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 26.
3. Align the keyhole slots in the upper switch housing with the
housing assembly screws installed previously.
4. Turn the upper switch housing counterclockwise until the
housing assembly screws are firmly situated in the narrow end
of the keyhole slots as shown in Figure 27. Install the one re-
maining #6-32 x 3/8" housing assembly screw into the third
hole in the upper switch housing. Tighten all three screws firmly.
C C C C C A A A A A U U U U U T T T T T I I I I I O O O O O N: M N: M N: Ma a a a a k k k k k e s N: M e sur ur ur ur ure t e s e s
N: M e s
c c c c c ur ur ur ur ure e e e e l l l l l y a y a y a y a y at t t t t t t t t t a a a a a c c c c c h h h h h e e e e e d t d t d t d t d to t o t o t o t o th h h h h e s e s e s e s e sw w w w w i i i i i t t t t t c c c c c h h
ur ur ur ur ure t e to p e t e t o p o p o pr r r r r o o o o o p p p p p e e e e e r r r r r l l l l l y a y a y at t t t t t t t t t a a a a a c c c c c h a y a h an n n n n d t h a h a
e t o p y a h a
s s s s s e e e e e mb mb mb mbl l l l l y s mb y s y s y s y sc c c c c r r r r r e e e e e w w w w w s c s c s c s c s co o o o o ul ul ul ul uld r d r d r d r d re e e e e s s s s s ul ul ul ul ult in t
f f f f f i i i i i x x x x x t t t t t ur ur ur ur ure f e f e f e f e fa a a a a llin llin lling g g g g . . . . . llin
llin
attaching the lower switch housing
1. Connect the upper plug connector from the motor to the lower
plug connector in the lower switch housing assembly. See Fig-
ure 30.
NOTE: Both plug connectors are polarized and will only fit to-
gether one way. Make sure that both connectors are properly
aligned before connecting them together. Incorrect connec-
tion could cause improper operation and damage to the prod-
uct.
2. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower
switch housings. Attach the lower switch housing to the up-
per switch housing with three #6-32 x 3/8" housing assembly
screws. See Figure 30.
41847-01 04/21/2003
e t e th h h h h e up e t e upp p p p p e e e e e r s e up e up r s r s r s r sw w w w w i i i i i t t t t t c c c c c h h h h h h h ho o o o o u u u u u sin sin sin g i g i g i g is s
e t e up h h sin sing i
h h h h h ho o o o o u u u u u sin h h sing m sin sin sin g m g m g m g mo o o o o un un un un unt t t t t in in in in ing p g p g p g p g pl l l l l a a a a a t t t t t e e e e e . F . F . F . F . Fa a a a a il- il- il- il- il-
d t d ti i i i i g g g g g h h h h h t t t t t e e e e e n a d t n a n a n all t ll t ll t ll thr hr hr hr hre e e e e e h e h e h e ho o o o o u u u u u sin sin sing a sin
d t n a ll t e h sin
t in t t in t t in th h h h h e s t in t e s e s e s e sw w w w w i i i i i t t t t t c c c c c h h h h h ho o o o o u u u u u sin h h h h sin sing a sin sin g a g a g an n n n n d li g a

operating your ceiling fan

1. Turn on electrical power to the fan.
2. The fan pull chain controls power to the fan. The pull chain
has four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• The chain uses a breakaway connector that separates if
the chain is jerked. If this happens, simply reinsert the chain
into the connector.
3. The light pull chain controls power to the light. The pull chain
has two settings: On and Off.
4. Ceiling fans work best by blowing air downward (counterclock-
wise blade rotation) in warm weather to cool the room with a
direct breeze. In winter, having the fan draw air upward (clock-
wise blade rotation) will distribute the warmer air trapped at
the ceiling around the room without causing a draft. Refer to
Figure 32.
s s s s s s s se- e- e- e- e-
g as s s s s - - - - - g a g a
g a
d li d li d lig g g g g h h h h h t t t t t d li
To change the direction of air flow, turn the fan off and let it
come to a complete stop. Slide the reversing switch on the fan
to the opposite position as shown in Figure 33. Restart fan.
F F F F F i i i i i g g g g g ur ur ur ur ure 33 - P
F F F F F i i i i i g g g g g ur ur ur ur ure 32 - A e 32 - A e 32 - A ir fl l l l l o o o o o w p ir f ir f w p w p w pa a a a a t t t t t t t t t t e e e e e r r r r r n n n n n s s s s s
e 32 - Air f e 32 - A ir f w p
Fan Pull Reversing
Chain Switch
e 33 - P e 33 - P e 33 - P e 33 - Pull c ull c ull c ull c ull ch h h h h a a a a a in a in a in an n n n n d r in a in a d re e e e e v v v v v e e e e e r r r r r sin d r d r d r sin sin sing s sin
© 2003 Hunter Fan Company
g s g sw w w w w i i i i i t t t t t c c c c c h h h h h g s g s