Table of Contents
Advertisement
installing accessory light fixtures
To install the light fixture, follow the instructions included with the
light fixture for wiring, mounting, and assembly.
operating your ceiling fan
1.
Turn on electrical power to the fan.
2.
The fan pull chain controls power to the fan. The pull chain
has four settings in sequence: High, Medium, Low and Off.
•
Pull the chain slowly to change settings.
•
Release slowly to prevent the chain from recoiling into the
blades.
•
The chain uses a breakaway connector that separates if
the chain is jerked. If this happens, simply reinsert the chain
into the connector.
3.
Ceiling fans work best by blowing air downward (counterclock-
wise blade rotation) in warm weather to cool the room with a
direct breeze. In winter, having the fan draw air upward (clock-
wise blade rotation) will distribute the warmer air trapped at
the ceiling around the room without causing a draft. Refer to
Figure 27.
F F F F F i i i i i g g g g g ur ur ur ur ure 27 - A
e 27 - A
e 27 - A
e 27 - A
e 27 - Air f
To change the direction of air flow, turn the fan off and let it
come to a complete stop. Slide the reversing switch on the fan
to the opposite position as shown in Figure 28. Restart fan.
Fan Pull
Chain
F F F F F i i i i i g g g g g ur ur ur ur ure 28 - P
e 28 - P
e 28 - Pull c
e 28 - P
ull ch h h h h a a a a a in a
ull c
ull c
e 28 - P
ull c
© 2003 Hunter Fan Company
ir f
ir fl l l l l o o o o o w p
ir f
ir f
w p
w pa a a a a t t t t t t t t t t e e e e e r r r r r n n n n n s s s s s
w p
w p
Reversing
Switch
in a
in an n n n n d r
in a
d r
d re e e e e v v v v v e e e e e r r r r r sin
d r
sing s
sin
sin
g s
g s g s
g sw w w w w i i i i i t t t t t c c c c c h h h h h
in a
d r
sin
cleaning your ceiling fan
caring for finishes
For cleaning, a soft brush or lint-free cloth should be used to pre-
vent scratching the finish. A vacuum cleaner brush nozzle can re-
move heavier dust. Surface smudges or an accumulation of dirt
and dust can easily be removed by using a mild detergent and a
slightly dampened cloth. An artistic agent may be used, but never
use abrasive cleaning agents as they will damage the finish.
caring for blades
Wood finish blades should be cleaned with a furniture polishing
cloth. Occasionally, a light coat of furniture polish may be applied
for added protection and beauty. Painted and high-gloss blades
may be cleaned in the same manner as the fan finish.
troubleshooting
Problem: Nothing happens; fan does not move.
1.
Turn power on, replace fuse, or reset breaker.
2.
Loosen canopy, check all connections according to the
w w w w w ir ir ir ir irin in in in ing t
g t g t
g t
g th h h h h e f e f e f e f e fa a a a a n n n n n section.
3.
Check the plug connection in the switch housing.
4.
Push motor reversing switch firmly up or down to ensure
that the switch is engaged.
5.
Pull the pull chain to ensure it is on.
6.
Remove the shipping bumpers.
Problem: Noisy operation.
1.
Tighten the blade bracket screws until snug.
2.
Tighten the blade screws until snug.
3.
Check to see if the blade is cracked. If so, replace all the
blades.
4.
Change to an approved speed control.
5.
Check and tighten the screws in the switch housing
mounting plate and in the upper and lower switch hous-
ing.
Problem: Excessive wobbling.
1.
If your fan wobbles when operating, use the enclosed bal-
ancing kit and instructions to balance the fan.
2.
Tighten all blade and/or blade iron screws.
3.
Turn power off, support fan very carefully, and check that
the hanger ball is properly seated.
If you need parts or service assistance, please call 888-830-1326 or
visit us at our WEB site at http://www.hunterfan.com.
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
9 9 9 9 9
41835-01 04/30/2003
Advertisement
Table of Contents
