Genius DIABLO Manual For The Installer page 7

We thank you for having chosen one of our products. GENIUS is
certain that from it you will obtain all the performance you require.
All our products are the result of years of experience in the field
automated systems, with the added advantage of being part of
one of the sector's leading groups.
Inside the manual you will find a detachable booklet
containing all the images for installation.
IMPORTANT NOTES FOR THE INSTALLER
• Before beginning installation of the operator, carefully read the
entire manual.
• Keep this manual for future reference.
• Correct operation and the declared technical specifications are
obtained only by complying with the instructions contained in
this manual and using GENIUS accessories and safety devices.
• If a mechanical clutch device is not available, use a control unit
featuring an adjustable electronic clutch.
• This automated system has been designed and built for
controlling vehicle access. Avoid any different use.
• The operator must not be used to control emergency exits or
gates installed on emergency lanes (escape routes).
• If the leaf you wish to motorise features a built-in door for
pedestrian passage, the door must be equipped with a safety
switch in order to disable operation of the gate when the door
is open.
• Do not pass while the gate is moving.
• Whatever is not explicitly provided for in these instructions is to
be considered strictly forbidden.
DESCRIPTION OF THE COMPONENTS
With reference to Fig. 1
Pos
a
Supporting box
b
Operator
c
Gate support frame
d
Locking frame
e
Release device
f
Cable runner
g
Draining hole
h
Lubrication hole
i
Drive pinion
j
Closing cover
k
Plug
TECHNICAL SPECIFICATIONS
a
System power supply
Motor power supply
Absorbed power (W)
Max torque (Nm)
Nominal torque (Nm)
Opening angle (°)
Angular speed (°/sec.)
Max leaf weight (Kg)
Max leaf length (m)
Usage type
Max consecutive cycles b
Daily cycles b
Max continuous operating
time
Protection class
Noise dB(A)
Description
230V~ 50Hz
115V~ 60Hz
24V
140
200
130
180
6
See chart in fig. 2
2
2.5 (with electronic lock)
Residential
30
50
O.T. 17 min.
IP67
<70
Operating temperature (°C)
Operator weight (Kg)
Operator dimensions (mm)
Supporting box dimensions
(mm)
a Depending on the paired control unit.
b Values obtained from laboratory testing.
INSTALLATION
Electrical preparations (standard system) Fig. 4.
Pos Description
a
Gearmotor
b
Control unit (system power supply)
c
TX Photocells
d
RX Photocells
e
Key selector
f
Flashing lamp
For cable installation, use adequate rigid and/or flexible
tubes.
Separate the 230/115V~power cables from the low-voltage
ones.
m
otor cable diameter
Operator - Board distance
Up to 15 m
Conductor
2.5 mm 2
diameter
Preliminary checks
1. The mechanical elements used for construction must comply
with EN 12604 and EN 12605 Standards.
2. The leaf structure must be suitable for automation.
3. Minimum distance between the lower edge of the leaf and the
floor as shown in fig. 5.
4. Presence of mechanical leaf limit stops.
5. Check for the presence of only the upper hinge.
The condition of the structure directly affects the
reliability and safety of the automated system.
Before installing the automated system, carry out any
necessary smith work on the gate
Walling in the supporting box
1. Choose the orientation of the box according to the dimensions
shown in fig. 6 and 7.
2. Dig a hole for positioning the box, fig. 8.
Modify the dimensions of the hole according to the type
of ground (the dimension in figure 8 refer to the minimum
dimensions of the hole).
3. Position the box as shown in fig. 9.
4. Place a rigid tube or a flexible sheath for passage of the power
supply cables, fig. 10 ref a.
5. Place a tube for draining rain water, fig. 10 ref. b.
6. Ensure that the box is walled-in flat.
DIABLO
Page 5
Guide for the installer
-20 +55
6.5
311x168 H120
See figure 3
Cable nr.
and diam.
2 x See table
3x1.5mm
2
2x0.5mm
2
4x0.5mm 2
2x0.5mm (BUS)
2
2x0.5mm 2
2x1.5mm 2
From 15 m to From 25 m
25 m to 35 m
4 mm 2 6 mm 2