Download
Share
Print this page
Grizzly POWER FEED H8370 Instructions
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Accessories
  5. POWER FEED H8370
  6. Instructions

Grizzly POWER FEED H8370 Instructions

Power feed for mill/drills
Hide thumbs
1
2
3
4

Advertisement

Quick Links

Download this manual

Specifications

Motor.................................................. 110V.60Hz
Speed................................................ 0–270.RPM
Maximum.Torque..................................560.in./lb.
Bevel.Gear.to.Drive.Gear.Ratio................... 2.8:1
Inventory
Refer.to.Figure 1.and.the.table.below.to.inventory.
the.contents.of.the.shipping.box.
REF PART #
DESCRIPTION
1V2
PH8370001V2 MOUNTING ASSY W/O WIRES V2.07.11
2
PH8370002
GEAR SAFETY COVER
3V2
PH8370003V2 PWR FEED & LIMIT SWITCH ASSY V2.07.11
4
PH8370004
LIMIT STOP
5
PH8370005
LIMIT SWITCH BRACKET
6
PH8370006
LEADSCREW GEAR
7V2
PH8370007V2 RAPID SWITCH W/LED V2.07.11
8
PH8370008
ZYTEL GEAR
if. any. nonproprietary. parts. are. missing. (e.g.. a.
washer.or.a.spacer),.we.will.gladly.replace.them;.
or. for. the. sake. of. expediency,. replacements. can.
be.obtained.at.your.local.hardware.store.
CoPyRiGHT.©.MARCH,.2008.By.GRizzly.inDuSTRiAl,.inC..ReViSeD.july,.2011.(Bl)
WaRNINg: NO PORTION OF THIS MaNUaL May bE REPRODUCED IN aNy SHaPE
OR FORM WITHOUT THE WRITTEN aPPROvaL OF gRIzzLy INDUSTRIaL, INC.
(FoR.MoDelS.MAnuFACTuReD.SinCe.7/11).#TS10533..PRinTeD.in.TAiWAn
MODEL H8370

POWER FEED

FOR MILL/DRILLS
INSTRUCTIONS
Figure 1..Model.H8370.inventory.
If you need help with your new power feed, call
our Tech Support at: (570) 546-9663.
Wear safety glasses dur-
ing the entire setup pro-
cess!

Advertisement

loading

Related Manuals for Grizzly POWER FEED H8370

Summary of Contents for Grizzly POWER FEED H8370

  • Page 1: Power Feed

    CoPyRiGHT.©.MARCH,.2008.By.GRizzly.inDuSTRiAl,.inC..ReViSeD.july,.2011.(Bl) WaRNINg: NO PORTION OF THIS MaNUaL May bE REPRODUCED IN aNy SHaPE OR FORM WITHOUT THE WRITTEN aPPROvaL OF gRIzzLy INDUSTRIaL, INC. (FoR.MoDelS.MAnuFACTuReD.SinCe.7/11).#TS10533..PRinTeD.in.TAiWAn MODEL H8370 POWER FEED FOR MILL/DRILLS INSTRUCTIONS Figure 1..Model.H8370.inventory.

  • Page 2: Functional Overview

    Functional Overview The. Model. H8370. power. feed. is. designed. to. install. on. the. left. side. of. a. mill/drill. table. to. pro- vide.powered.longitudinal.movement.of.the.table.. Refer.to.Figures 2–3.and.the.descriptions.below. to.become.familiar.with.the.functional.parts.of.the. power.feed.system. Figure 2..Power.feed.controls. Figure 3..limit.switch.and.stops. a.. Direction Lever: Starts,.reverses,.and.stops. longitudinal.table.movement. b.. Rapid Movement button: Moves.the.table.at.
  • Page 3 Figure 5. Table Bracket Figure 5..Table.bracket.mounted.on.the.lip.of. the.table.trough. 5.. Mark.the.points.on.the.table.where.the.table. bracket.hex.bolts.make.contact,.then.remove. the.bracket.from.the.table. 6.. Spot.drill.the.points.marked.in.Step 5.to.give. the.hex.bolts.a.small.spot.to."bite".the.table. without.slipping.on.the.rough.cast.surface. 7.. Set.the.bracket.back.on.the.table.and.tighten. down.the.hex.bolts. 8.. install. the. mounting. bracket. onto. the. power. feed.assembly.with.the.two.cap.screws.pro- vided,. as. shown. in. Figure 6,. but. do. not. yet. fully.tighten.them.
  • Page 4 Bracket Figure 10..installing.the.bracket.and.limit.switch. 13.. Make.sure.the.on/oFF.switch.is.in.the.OFF. position,.then.connect.the.power.feed.unit.to. a.grounded.110V.power.source. Maintenance Clean.and.lubricate.the.power.feed.gearing.every. three.months.of.normal.use. 1.. DiSConneCT. THe. Mill/DRill. AnD. PoWeR.FeeD.FRoM.PoWeR! 2.. Remove.the.gear.safety.cover. 3.. Remove. the. power. feed. assembly. from. the. table.bracket. 4.. Clean. the. debris. and. built-up. grime. from. the.drive.gear,.leadscrew.gear,.and.the.sur- rounding.area. 5.. Brush.a.light.coat.of.all-purpose.grease.onto.