Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Grizzly H6329
Summary of Contents for Grizzly H6329
- Page 1 ⁄ gallon paint tanK instruction manual Copyright © MAy, 2009 By grizzly industriAl, inC. Warning: no portion of this manual may be reproduced in any shape or form Without the Written approval of grizzly industrial, inc. #Cr11799 printed in ChinA...
- Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use.
-
Page 3: Safety Instructions For Pneumatic Tools
Always wear a respi- rator niosh approved for the type of material being processed. Model h6329 2 ⁄ gallon paint tank safety indicates an imminently hazardous situation which, if not avoided, Will result in death or serious injury. - Page 4 23. be aWare of hose location. hoses can easily become a tripping hazard when laid across the floor in a disorganized fashion. 24. do influence alcohol, or When tired. Model h6329 2 ⁄ gallon paint tank untrained under drugs...
-
Page 5: Cleaning And Maintenance
Model h6329 2 ⁄ gallon paint tank 6. -
Page 6: Specifications
Model h6329 as supplied when the manual was prepared. however, owing to grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of grizzly. - Page 7 Model h6329 2 ⁄ setup h6329 inventory (figure 1) ... Qty a. paint tank... 1 b. Caster Wheel Assemblies ... 4 —hex nuts M8-1.25 ... 4 —Flat Washers 8MM ... 4 —lock Washers 8MM ...
-
Page 8: Tank Assembly
2. Controls and features. 5. Connect the your air supply hose and onto the inlet fitting on the regulator (figure 4). figure 4. spray gun fittings installed. Model h6329 2 Vent Valve " push-on hose fittings to ⁄ gallon paint tank... - Page 9 Model h6329 2 ⁄ gallon paint tank tank regulator and spray guns the pressure regulator on the paint tank controls the pressure in the tank.
-
Page 10: Operation
Gun air supply ON/OFF valve. 120 PSI Max. Tank regulator setting is typically 10 PSI. NEVER Tank air exceed 45 PSI Max. supply ON/OFF valve. Model h6329 2 operation Water separator. 120 PSI Max. Compressor ⁄ gallon paint tank... -
Page 11: Cleaning And Lubrication
Vent Valve figure 6. regulator and vent valve. Model h6329 2 ⁄ 3. open the tank lid. 4. empty and clean the tank of all paint, and fill it with 1 quart of solvent. 5. replace the lid, tighten the clamps, and spray the gun until it sprays clean solvent. - Page 12 3. Clean rim and gasket. 1. Mix or thin paint according to manufacturer's instruc- tions. 1. turn air pressure ON. 2. replace pressure gauge. 1. reduce tank pressure to 25-30 psi. 2. replace safety valve. Model h6329 2 ⁄ gallon paint tank...
-
Page 13: Troubleshooting
1. no pressure at gun. 2. Fluid passages dirty. 3. Fluid control closed. 4. out of paint. 5. Material too thick. Model h6329 2 ⁄ gallon paint tank troubleshooting solution 1. tighten fluid tip or replace seat with new one. - Page 14 3. slow down and maintain consistent even parallel stroke. 1. Clean or replace both. 1. Wait until finish is dry and cured, re-sand clean and re-prime, and repaint. 2. install an in-line air filter. Model h6329 2 ⁄ gallon paint tank...
- Page 15 5,6,37 REF PART # DESCRIPTION PH6329001 HANDLE PH6329002 LID GASKET PH6329003 COMPLETE LID ASSEMBLY PH6329004 TANK PN03M HEX NUT M8-1.25 PLW04M LOCK WASHER 8MM PH6329007 SWIVEL CASTER PH6329008 AIR INLET CONNECTION PH6329009 AIR DEFLECTOR PH6329010 FLUID OUTLET BODY...