Table of Contents
Advertisement
Self-diagnosis Code
Symptom/State
Block
Detailed
Function
Code
E
9
4
0
2
BGM data error
E
9
5
0
0
GPS hardware error
E
9
6
0
0
Map area mount error
E
9
7
0
0
Projector hardware error
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-6. METHOD OF COPING WITH SHIFT LENS ERROR
LD-297 BOARD (SIDE A)
IC5601
C5636 C5640
C5642 C5643
Measurement points on the LD-297 board
HXR-NX30C/NX30E/NX30J/NX30N/NX30P/NX30U
Correction
Check the CPU (IC1301 on the VC-658 board).
NX30E/NX30J/NX30N/NX30P/NX30U:
Check whether the FFC-254 flexible flat cable is broken, and check
whether it is inserted imperfectly.
If there is no problem the flexible board, inspect or replacement of
the GP-037 board.
NX30E/NX30J/NX30N/NX30P/NX30U:
Inspect or replacement of the LD-297 board.
Turn power off and turn power on again.
LD-297 BOARD (SIDE B)
R5632
Fig. 1
Note: The length of low section will vary a little depending on the conditions.
Change in output voltage of R5632 on the LD-297 board
1-6-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
1
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5632 in the periphery of IC5601 on the LD-297 board, turn the
2
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
3
the camera control circuit (IC1301 of VC-658 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-6-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Order
AdjustBlock
AdjustCode
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the
1
[SERVICE] tab.
Check if the shift lens moves while setting the order 1.
2
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
While setting the order 1, measure with an oscilloscope the output voltage of C5642 and C5643 in
3
the periphery of IC5601 on the LD-297 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note).
4
When the output voltage varied, proceed to the order 5.
5
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5632 in the periphery of IC5601 on the
6
LD-297 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note).
7
If it does not change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-658 board
and IC5601 of LD-297 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5
about 330 msec
Fig. 2
Procedure
Order
– ENGLISH –
Advertisement
Table of Contents
