Table of Contents
Advertisement
Self-diagnosis Code
Symptom/State
Block
Detailed
Function
Code
E
4
1
0
0
Wi-Fi Module Hardware Error
Zoom operations fault
E
6
1
1
0
(Cannot initialize zoom lens.)
The abnormalities in initialization of the focus
E
6
1
1
1
lens and the abnormalities in initialization of
the zoom lens occurred simultaneously.
Reset position detection error on the stepper
E
6
1
3
0
iris initializing
Error in detection of the Reset Position at the
E
6
1
3
1
time of Stepper IR Filter initialization.
Handshake correction function does not work
E
6
2
0
0
well. (With PITCH angular velocity sensor
output stopped.)
Handshake correction function does not work
E
6
2
0
1
well. (With YAW angular velocity sensor
output stopped.)
E
6
2
0
2
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller com-
E
6
2
0
3
munication abnormality among.
Image vibration correction during handshake
E
6
2
0
4
function does not work.
E
6
2
1
0
Shift lens initializing failure.
E
6
2
1
1
Shift lens overheating (Pitch)
E
6
2
1
2
Shift lens overheating (Yaw)
E
6
2
2
0
Abnormality of thermistor.
E
6
2
3
0
Abnormal CPU
E
9
1
0
1
Abnormality when flash is being charged.
E
9
1
0
2
Abnormality of LED Video light.
Abnormality of LED Video light Tempera-
E
9
1
0
3
ture detection.
Note 3: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-PJ800/PJ810/PJ810E/PJ820/PJ820E_L2
Correction
Check that connection between CN4902 on the VC-1022 board and
CN2301 on the WF-1004 board by FP-2181 flexible board.
Inspect the lens block zoom signal (pin wg, wh, rj, rk of CN6801 on
the LD-1014 board when zooming is performed when the zoom lever
is operated, and the zoom motor drive circuit (IC6800 on the LD-1014
board) when zooming is not performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Turn the power on to open lens barrier. Disconnect the battery or power
cord, and then connect again.
Confirm that the iris blades in lens are working.
If iris blades do not working, check the iris motor drive IC in lens drive
block (pin ef, eg, ej, ek, r;, ra of CN6801 on the LD-1014 board).
If iris blades work normally, confirm that they are closing completely
and confirm following item.
･ Case of the iris blades do not close normally Replace the lens block).
･ Case of "E: 61: 30" is appeared and iris blades closed completely.
Confirm that communication with lens block is normal.
･ Case of LCD is not displayed normally Check that connection be-
tween CN1001 on CM-1007 board and CN4004 on VC-1022 board
by LF-2063 flexible board.
･ Case of LCD is displayed normally Replace the lens block.
Check that connection between CN6801 on the LD-1014 board and
the lens block by LF-2026 flexible board.
Inspect PITCH angular velocity sensors (SE7701 on the LD-1014
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE7701 on the LD-1014 board)
peripheral circuits.
Refer to "1-6-1. E : 62 : 02 (Abnormality of IC for Steadyshot) Oc-
curred".
Inspect the steadyshot circuit (IC6800 on the LD-1014 board).
Inspect the image vibration angular velocity sensors (SE7711 on the
OC-1003 board) peripheral circuits.
Replacement of lens block (Note 3).
If an error occurs again, replace the LD-1014 board.
Refer to "1-6-2. E : 62 : 11 (Shift Lens Overheating (Pitch)) Occurred".
Refer to "1-6-3. E : 62 : 12 (Shift Lens Overheating (Yaw)) Occurred".
Refer to "1-6-4. E : 62 : 20 (Abnormality of Thermistor) Occurred".
Turn power off and turn power on again.
Check or replace the LED Flash/Video light or charging capacitor.
Check or replace the LED Flash/Video light or charging capacitor.
Check or replace the LED Flash/Video light or charging capacitor.
Self-diagnosis Code
Symptom/State
Block
Detailed
Function
Code
Battery current value goes over the max
E
9
2
0
1
discharge current
Fault of writing or erasing the flash mem-
E
9
4
0
0
ory
E
9
4
0
1
Internal flash memory fault
E
9
4
0
2
BGM data error
E
9
5
0
0
*
GPS hardware error
E
9
5
0
1
Acceleration sensor HW error
E
9
6
0
0
Map area mount error
*
E
9
7
0
0
Projector hardware error
Note: Functions of codes with * mark are not provided in this unit.
1-6. METHOD OF COPING WITH SHIFT LENS ERROR
LD-1014 BOARD (SIDE A)
Measurement points on the LD-1014 board
1-3
– ENGLISH –
Correction
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occurred after replacing the battery. If the symp-
tom is still occurred, overhaul inspection is needed. Check each
output of DC/DC converter (IC5100 on the VC-1022 board) with
connected the DC JACK (J901) on the VC-1022 board.
(The minimum connection to periphery)
PJ810/PJ810E:
Inspect the flash memory (IC8101 on the MM-102 board).
PJ800/PJ820/PJ820E:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).
PJ810/PJ810E:
Inspect the flash memory (IC8101 on the MM-102 board).
PJ800/PJ820/PJ820E:
Inspect the flash memory (IC8101, IC8201 on the MM-102 board).
Check the CPU (IC6000 on the VC-1022 board).
Turn power off and turn power on again.
Check that connection between CN4901 on the VC-1022 board and
CN4501 on the PD-1027 board by FP-2180 flexible board.
Turn power off and turn power on again.
Turn power off and turn power on again.
C6814 C6815
IC6800
R1401
C6816 C6817
Fig. 1
Advertisement
Table of Contents
