IHP BWBK Quick Start Manual

Door ADJUStMENt AND CArE iNStrUCtioNS
For USE WitH FirEPLACES LiStED iN tABLE 1
kit CoNtENtS
1 ea. Door Assembly
1 ea. Instruction Sheet
BLACk Door kit
Cat. No. Model
H0516 BWBk Brentwood™ SP and Montecito™
Table 1
GENErAL iNForMAtioN
This instruction sheet explains how to adjust the alignment of the door
and includes glass care instructions.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning.
ALL WArNiNGS AND PrECAUtioNS iN tHE iNStALLAtioN AND
oPErAtioN MANUAL ProViDED WitH tHE APPLiANCE APPLY to
tHESE iNStrUCtioNS.
SHUt DoWN tHE APPLiANCE AND ALLoW it to CoMPLEtELY CooL
BEForE ProCEEDiNG.
Door ADJUStMENt
The door of the Brentwood™ fireplace must be completely airtight. To
make sure that the door is totally airtight, a paper should not be able to
slide between the fireplace facade and the door's gasket. If the door is
not totally airtight, there is a screw on the right side of the fireplace facade
that can be tightened to adjust the door.
If the alignment of the door needs to be adjusted, simply loosen the up-
per and the lower screws on each hinge which fix the door to the facade
(notice that the middle screw does not need to be loosened). The door
can then be moved side-ways in order to allow for a proper fit.
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor
for fireplace code information.
Printed in U.S.A. © 2002 IHP LLC
P/N F132 rev. A 07/2013
Description
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
P/N F132
rev. A, 07/2013
BrENtWooD™ AND MoNtECito™ FirEPLACES
Too much compression of the gasket between the door and the fireplace
facade (on the hinges side) will make closing the door difficult. Adjust-
ing the space between the door and the fireplace facade will solve that
problem. To adjust, loosen all the screws on each hinge that are fixed
on the door. Push the door toward the fireplace facade to increase the
space or pull it toward you to reduce that space.
Hinge Screws
Gasket Adjustment Screw
Figure 1
GLASS CArE - rEPLACEMENt
The glass used for the Brentwood fireplace is a high temperature ceramic
glass (1400° F). If the glass breaks, it must be replaced with a ceramic
glass. Tempered glass or ordinary glass will not withstand the high
temperatures of the Brentwood fireplace. Replacement glass should
be purchased from a IHP dealer. Do Not oPErAtE tHE UNit WitH
CrACkED or BrokEN GLASS.
GLASS CArE - CLEANiNG
The Brentwood fireplace is designed to keep the glass clean under normal
operating conditions. If the Brentwood fireplace is operated continuously
with the combustion air damper closed, the glass will tend to get dirty
unless the fuel, firebox and glass are maintained at hot temperatures. To
clean the glass, there are a number of specially designed cleaners. Your
IHP dealer can recommend a suitable cleaner which is available in your
area. Regular household glass cleaners will not clean creosote. Do not
use abrasives such as steel pads, steel wool or oven cleaner as they will
scratch the glass.
iHP
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
HEARTH PRODUCTS
KITS AND ACCESSORIES
Door kit
1