Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR HEATFLO KITS
[FOR USE WITH MODELS: Compass45TEN, CompassDLX45TEN, Compass55TEN, CompassDLX55TEN, DRL2000 45/55 and DRL3500 45/55]
KIT CONTENTS (see Figure 1)
1 ea. Register Assembly
1 ea. Register Trim
4 ea. 4-1/2" x 24" Flex Pipe (stretches up to 70" in length)
8 ea. Gear Clamp
2 ea. Register Support Bracket
18 ea. Screws
4 ea. Collar Mounting Plate
4 ea. Small Collar
4 ea. Large Collar
1 ea. Hood
TOOLS / SUPPLIES REQUIRED (not included)
Electric Drill/Driver Gun
Phillips Screwdriver Bits
5/16 Nut Driver
3/8 Nut Driver
Wood Screws
HeatFlo™ Kit
Cat. No.
Model Number
F4454
HTFLO-DV45
F4453
HTFLO-DV55
GENERAL INFORMATION
The HeatFlo™ system is designed to redirect the convective heat
of the fireplace from the front of the unit, above the glass, to
a location higher on the wall. The use of this kit allows for TV
installations closer to the fireplace or in recessed wall cavities
above the fireplace (see Tables 1 and 2, Page 3).
When Installing this kit, reference the framing dimensions and
follow the framing instructions shown on the fireplace installation
Instructions. Follow all other installation requirements for the
fireplace as detailed in the installation manual.
REFER TO INSTALLATION INSTRUCTIONS AND CARE AND
OPERATIONS MANUAL (IICO) FOR FRAMING DETAILS BEFORE
INSTALLING THIS KIT.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE FIREPLACE APPLY
TO THESE INSTRUCTIONS.
P/N 901068-00
REV. A 07/2021
Kit Name
Kit, HeatFlo 45 DV Units
Kit, HeatFlo 55 DV Units
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
KITS AND ACCESSORIES
Register Trim
Register Assembly
Flex Pipes
Register Support
Small Collars
Brackets
Figure 1 - Kit Contents Overview
Figure 1
INSTALLER: Leave this manual with the fireplace.
CONSUMER: Retain this manual for future
reference.
WARNING
This kit must be installed by a qualified installer,
service agency, or gas supplier at the time of the
fireplace installation. These instructions must
be used in conjunction with the installation and
operation manual provided with the fireplace.
HEARTH PRODUCTS
HeatFlo™ Kit
Fireplace Hood
Collar Mounting
Gear Clamps
Plates
Large Collars
1
Advertisement
Related Manuals for IHP HeatFlo Kit
Summary of Contents for IHP HeatFlo Kit
- Page 1 HEARTH PRODUCTS KITS AND ACCESSORIES P/N 901068-00 HeatFlo™ Kit REV. A 07/2021 INSTALLATION INSTRUCTIONS FOR HEATFLO KITS [FOR USE WITH MODELS: Compass45TEN, CompassDLX45TEN, Compass55TEN, CompassDLX55TEN, DRL2000 45/55 and DRL3500 45/55] KIT CONTENTS (see Figure 1) Register Trim Register Assembly Fireplace Hood 1 ea.
-
Page 2: Framing Dimensions
12” minimum on a flush wall and at 18" for a recessed installation, to reduce the amount of heat that reaches the television. The homeowner must understand that IHP does not take responsibility for any negative impact to televisions placed near this fireplace. - Page 3 See Tables 1 and 2 for TVs Installed above the fireplace: WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to protect from contact with hot surfaces. TVs should not be used in situations where the actual TV temperature exceeds the manufacturer’s technical specification. Contact the TV manufacturer directly if you cannot locate this information or have questions regarding this information.
- Page 4 Colla HEATFLO™ KIT INSTALLATION Fireplace Top NOTICE Metal Knockout Insulation Plug This kit must be installed by a qualified installer, service agency, or gas supplier at the time of the Heat Deflector fireplace installation. These instructions must Metal Knockout be used in conjunction with the installation and operation manual provided with the fireplace.
- Page 5 HEATFLO INSTALLATION NOTES: • DO NOT SLICE OR RUPTURE FLEX PIPES! 1. Mount the register into the framed opening by tilting forward and • Flex pipe stretches up to 2.9 times its compressed length (i.e., inserting from the back while rotating into place with register 24”...
- Page 6 Clearance Around into Place Flex Pipes Figure 13 - HeatFlo Kit Installed Figure 13 CAUTION: Flex pipe should be stretched out from its compressed state before installation. DO NOT over stretch the Flex. Make sure the flex pipe is slightly loose (but not sagging) when installed to allow for expansion and contraction. Flex pipe must not come in contact with combustible materials.
- Page 7 sheet, if possible. This will minimize the joints adjacent to the fireplace FINISHING FIREPLACE opening. The appliance is designed to mate with 1/2” wall sheathing materials such as drywall, plywood, wood composites, or non-combustible materials. Tape wall board joints around the fireplace opening with fiberglass-mesh tape.
- Page 8 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Innovative Hearth Products (IHP) reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.