IHP GCKSMS557051NP Quick Start Manual

GAS CONVERSION KIT FOR SIT MILLIVOLT FIREPLACES
NATURAL GAS TO PROPANE AND PROPANE TO NATURAL GAS
[FOR USE IN FIREPLACE MODELS LISTED IN TABLES 1 AND 2 ON PAGE 2]
KIT CONTENTS
Pilot Orifice, Main Burner Orifice, Low-Rate Orifice, Gas Conversion
Kit (containing Pressure Regulator Assembly),Conversion Sticker and
Conversion Sticker Form (to be filled out and affixed by installer)
REQUIRED TOOLS
Safety Gloves, 5/32" Allen Wrench, Torx Bit (T20 with 1/4" shank
and center hole) or Flat Blade Screwdriver, 1/2" Open-End Wrench
TURN OFF THE GAS SUPPLY TO THE APPLIANCE. DISCONNECT
ELECTRICAL POWER SUPPLY.
READ ALL THE STEPS BEFORE STARTING THE CONVERSION. IN-
STALLER NOTICE: THESE INSTRUCTIONS MUST BE LEFT WITH THE
APPLIANCE.
When installing gas components use pipe joint compound or
Teflon tape on all pipe fittings before installing (Do not use pipe
joint compounds on flare fittings).
NOTE: THE FIREPLACE MUST BE OFF AND COLD BEFORE PERFORM-
ING THE GAS CONVERSION.
ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS IN THE INSTAL-
LATION AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE
APPLY TO THESE INSTRUCTIONS.
GENERAL INFORMATION
Gas conversion kits are available to adapt the fireplace from the
use of one type of gas to the use of another. These kits contain all
the necessary components needed to complete the task including
labeling that must be affixed to ensure safe operation.
IMPORTANT CANADA
The conversion shall be carried out in accordance with
the requirements of the provincial authorities having
jurisdiction and in accordance with the requirements
of the CAN/CSA B149.1 Installation code.
IMPORTANT LE CANADA SEULEMENT
La conversion devra être effectuée conformément aux
recommandations des autorités provinciales ayant
juridiction et conformément aux exigences du code
d'installation CAN/CSA B149.1.
1 900792-00 NC
P/N 900792-00
Rev. NC, 08/2016
This conversion kit shall be installed by a qualified
service agency in accordance with the manufac-
turer's instructions and all applicable codes and
requirements of the authority having jurisdiction. If
the information in these instructions is not followed
exactly, a fire, explosion or production of carbon
monoxide may result causing property damage,
personal injury or loss of life. The qualified service
agency performing this installation is responsible
for the proper installation of this kit and assumes
responsibility for this conversion. The installation
is not proper and complete until the operation of the
converted appliance is checked as specified in the
manufacturers instructions supplied with the kit.
Cet équipement de conversion sera installé par
une agence qualifiée de service conformément aux
instructions du fabricant et toutes exigences et codes
applicables de l'autorisés avoir la juridiction. Si
l'information dans cette instruction n'est pas suivie
exactement, un feu, explosion ou production de
protoxyde de carbone peut résulter le dommages
causer de propriété, perte ou blessure personnelle de
vie. L'agence qualifiée de service est esponsable de
l'installation propre de cet équipment. L'installation
n'est pas propre et compléte jusqu'à l'opération de
l'appareil converti est chéque suivant les critères
établis dans les instructions de propriétaire provi-
sionnées avec l'équipement.
If you encounter any problems, need clarification of these
instructions or are not qualified to properly install this kit, contact
you local distributor or dealer.
IHP.US.com IHP.US.com
HEARTH PRODUCTS
KITS AND ACCESSORIES
MILLIVOLT GAS CONVERSION KITS
(SIT FIREPLACES)
WARNING
AVERTISSEMENT
900792-00 NC 1