Crown CT61001HX Original Instructions Manual page 25

Power tool designation
The power tool is designed to drive special staples or
nails�
Power tool components
1 Ventilation slots
2 Impact force regulator
3 Trigger
4 Belt clip *
5 Battery *
6 Indicators of the state of battery charge *
7 Control button of the state of battery charge *
8 Battery lock *
9 Magazine lock
10 Cover of magazine
11 Magazine
12 Indicator
13 Bolt
14 Plastic tip *
15 External plate
16 Internal plate
17 Guide of hammer
18 Allen key *
19 Staples (strip) *
20 Nails (strip) *
21 Charger *
22 Label *
23 Indicator (red) *
24 Indicator (green) *
25 Hammer
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool
remove the battery 5.
Mounting / dismounting / setting-up of
some elements is the same for all power
tool models, in this case specific models
are not indicated in the illustration.
Storing the Allen key (see fig. 1)
Fig� 1 shows where the Allen key 18 is stored and how
to remove it�
Installation and removal of the plastic tip (see fig. 2)
The plastic tip 14 prevents surface deformation when
staples or nails are driven� Fig� 2 shows the steps for
mounting / dismounting the plastic tip 14�
Installation of fasteners into the magazine (see
fig. 3-6)
Use fasteners (staples or nails) that are
suitable for your tool model (see explanatory
pictures and technical data table)� Fasteners
(staples or nails) are supplied as strips� Do
not attempt to load the fasteners one by one, as this
may lead to their bending inside the striking mechanism�
• Press on the upper part of the lock 9 (see fig. 3.1).
• Move the cover 10 back (see fig. 3.2).
• Installation of the staple strip 19:
• install the staples 19 as shown in figure 4.1. The
upper part of the staples 19 must adjoin the upper
part of the magazine 11 (see fig. 4.2);
• avoiding twisting of the staple 19, move the cov-
er 10 forward until the lock 9 locks into place (see
fig. 4.1).
• Installation of the nail strip 20:
• you can only use nails 20 of the following
lengths: 15 mm, 20 mm, 25 mm, 30 mm, 32 mm
(see fig. 5). This is due to the feature of the installa-
tion of the nails 20;
• install the nails 20 as shown in figure 6.1. The
lower part of the nails 20 must adjoin the lower part
of the magazine 11� The heads of the nail strip 20
must fit into one of the grooves on the rear wall of
the magazine 11 (see fig. 5);
• avoiding twisting of the nails 20, move the
cover 10 forward, until the lock 9 locks into place
(see fig� 6�1)�
Charging procedure of the power tool
battery
Initial operating of the power tool
The power tool is supplied with a partially charged
battery 5. Before the first use, the battery 5 must
be fully charged.
Charging process (see fig. 7-8)
• Press the battery lock 8 and remove the battery 5
(see fig. 7.1-8.1).
• Connect the charger 21 to the power supply�
• Insert battery 5 into charger 21 (see fig. 7.2-8.2).
• Disconnect the charger 21 from power supply after
charging�
• Remove the battery 5 from the charger 21 and
mount battery 5 in the power tool (see fig. 7�3-8�3)�
Charger indicators (see fig. 9-10)
Charger indicators 23 and 24 inform of the battery 5
charging process� Signals of the indicators 23 and 24
are shown on the label 22 (see fig. 9-10).
• Fig� 9�1, 10�1 - (the green indicator 24 is on, the
battery 5 is not inserted in the charger 21) - the
charger 21 is connected to the power network (ready
for charging)�
• Fig� 9�2, 10�2 - (the green indicator 24 is blinking,
the battery 5 is inserted in the charger 21) - the bat-
tery 5 is being charged�
• Fig� 9�3, 10�3 - (the green indicator 24 is on, the
battery 5 is inserted in the charger 21) - the bat-
tery 5 is fully charged�
• Fig� 9�4, 10�4 - (the red indicator 23 is on, the bat-
tery 5 is inserted in the charger 21) - the charging pro-
cess of the battery 5 is terminated due to inappropriate
temperature� When the temperature conditions are
normal, the process of charging will resume�
English
25