Advertisement
Available languages
Available languages
to be performed. Use of the power tool for operations
different from those intended could result in a hazard-
ous situation�
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations�
• Note that when you operate a power tool, please
hold the auxiliary handle correctly, which is helpful
when controlling the power tool� Therefore, proper
holding can reduce the risk of accidents or injuries�
Battery tool use and care
• Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack�
• Use power tools only with specifically designat-
ed battery packs. Use of any other battery packs may
create a risk of injury and fire.
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns�
• Avoid unintentional switching on. Ensure the
on / off switch is in the off position before inserting
battery pack. Carrying the power tool with your finger
on the on / off switch or inserting the battery pack into
power tools that have the switch in accidents�
• Do not open the battery. Danger of circuit�
• In case of damage and improper use of the bat-
tery, vapors may be emitted. Provide for fresh air
and seek medical help in case of complaints. The
vapors can irritate the respiratory system�
• When the battery is defective, liquid can escape
and come into contact with adjacent components�
Check any parts concerned� Clean such parts or re-
place them, if required�
• Protect the battery against heat, e.g., also
against continuous sun irradiation and fire. There
is danger of explosion�
WARNING! Read all safety warnings and
all instructions.
• Protect the battery charger from rain and mois-
ture. The penetration of water in a battery charger in-
creases the risk of electric shock�
• Do not charge other batteries. The battery charger
is suitable only for charging lithium ion batteries within
the listed voltage range� Otherwise there is danger of
fire and explosion.
• Keep the battery charger clean. Contamination
may cause the danger of electric shock�
• Check the battery charger, cable and plug each
time before using. Do not use the battery charger
when defects are detected. Do not open the battery
charger yourself and have it repaired only by quali-
fied personnel using original spare parts. Damaged
battery chargers, cables and plugs increase the risk of
electric shock�
• Do not operate the battery charger on easily in-
flammable surfaces (e.g. , paper , textiles , etc.) or
in combustible environments. There is danger of fire
due to the heating of the battery charger during charg-
ing�
Service
• Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained�
• Follow instruction for lubricating and changing ac-
cessories�
Safety guidelines during power tool op-
eration
Attention: the text contains the term
"accidental triggering", which means
the shot with a fastener that is not
controlled by a user. Please remember
that the accidental triggering can lead to serious
injuries or death of a user or persons around.
Before start to work
• You should always suppose that the power tool is
loaded and handle it carefully�
• Remove a battery from the power tool before the
installation of fasteners�
• Use fasteners of recommended type only; do not
use damaged, bent or rusted fasteners�
• Do not load fasteners of different sizes or different
types into the magazine at the same time, this may
cause the fasteners to get stuck inside the striking
mechanism�
When working
• When working, be sure to wear safety glasses
that provide both frontal and side protection� Eye
protection must comply with ANSI Z 87�1 (CAN/CSA/
Z94�3, GOST 12�4�011-89)� This rule applies to both
the worker and those who are nearby�
• Never point the power tool at yourself, other people,
or animals�
• Do not try to make a shot in an open area, it can be
dangerous for both you and those around you�
• Pull the trigger when doing work only� In all other
cases, such as when carrying the power tool or when
servicing, remove your finger from the trigger to
prevent accidental shot�
• It is strictly forbidden to change the power tool
design (for example, fix the contact tip in the depressed
position), as this could lead to accidental triggering�
• Keep hands and feet at a safe distance from the
contact tip when working�
• While pulling the trigger, hold the power tool securely
(do not tilt) and press the contact tip against the
surface, otherwise the fastener may become jammed,
ricochet, or crinkle inside the power tool�
• Power tools can generate sparks, so do not use
them near explosive or flammable materials.
• When working, keep in mind that utility lines can
pass under the surface to be treated, which you can
damage� Use special metal detectors and detectors
English
23
Advertisement
