Related Manuals for Jet JMD-2S
Summary of Contents for Jet JMD-2S
- Page 1 Milling Drilling Center JMD-2S Original: Operating Instructions JPW (Tool) AG Tämperlistrasse 5 CH-8117 Fällanden Switzerland Phone +41 44 806 47 48 +41 44 806 47 58 www.jettools.com 50000060M 2016-09...
-
Page 2: Ce Conformity Declaration
CE-Conformity Declaration Product: Milling Drilling Center JMD-2S Stock Number: 50000060M Brand: JET Manufacturer: JPW (Tool) AG, Tämperlistrasse 5, CH-8117 Fällanden, Switzerland On our own responsibility we hereby declare that this product complies with the regulations * 2006/42/EC Machinery Directive * 2014/30/EU... - Page 3 Do not operate the machine under the influence of drugs, In addition to the safety requirements contained in these alcohol or any medication. Be aware that medication can operating instructions and your country’s applicable change your behaviour. regulations, you should observe the generally recognized technical rules concerning the operation of metal machines.
-
Page 4: Important Safety Instruction
IMPORTANT SAFETY INSTRUCTION READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS TOOL Operator COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO ANY PRODUCT. THESE FACTORS MUST BE SUPPLIED BY THE OPERATOR. PLEASE REMEMBER: 1. When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. - Page 5 IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE, DO NOT OPERATE THE TOOL! Grounding Instructions This machine has a three-prong plug, the third prong is the ground. Plug this cord only into a three-prong receptacle. Do not attempt to defeat the protection the ground wire provides by cutting off the round prong.
- Page 6 FEATURE Base Cross feed handwheel Worktable Column (with dustproof) Drill chuck with arbor Chuck guard assembly Spindle sleeve locking handle Depth display Emergency stop switch Knob with potentiometer Electric control box Speed display Light Forward/0/Reverse switch Fine feeding handle Spindle box Vertical feed handwheel Column back cover Fine feeding locking handle...
-
Page 7: Mounting The Machine
Installation CAUTION! DO NOT ATTEMPT TO USE THE MACHINE UNTIL INSTALLTION IS CAMPLETED, AND ALL PRELIMINARY CHECKS HAVE BEEN MADE IN ACCORDANCE WITH THIS MANUAL. MOUNTING THE MACHINE The machine should be mounted on a strong, heavy workbench, of sufficient height so that you do not need to bend your back to perform normal operations. -
Page 8: Operation
Operation 1. Before starts to use this machine, operator should go through the instructions carefully so as to acquaint with the construction of the machines, the functions of the various controls and also the driving systems. 2. This machine uses touching button (see operation panel below), operating steps refer to the flow chart. - Page 9 4. When you control the mill and need quickly stop the spindle speed, you can clap the emergency stop switch (A), as this time the fault yellow light ( E) will bright. If you need restart the mill you need turn the F/O/R switch (D) to “0” position, then control as 1-2-3 steps.
- Page 10 Parts Breakdown For JMD-2S Milling Drilling Center（I） 17 35 68 67...
- Page 11 Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-I-01 Spindle box JMD2S-I-02 Cross recessed small pan head screw H M3*8 M4X6 JMD2S-I-03 Spindle below oil seal ring I JMD2S-I-04 B16 taper shank JMD2S-I-05 Cone roller bearing 32907 32907 JMD2S-I-06 Hexagon headed nut M5 JMD2S-I-07 Fine feeding handwheel...
- Page 12 Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-I-45 Eccentric sleeve locking block JMD2S-I-46 Motor connect plate JMD2S-I-47 Thrust ball bearing single 7/70 JMD2S-I-48 Worm shaft JMD2S-I-49 Worm eccentric sleeve JMD2S-I-50 Tighten the top rod JMD2S-I-51 Round pin A3*10 A3X10 JMD2S-I-52 Thrust ball bearing single 8106 8106...
- Page 13 Parts Breakdown For JMD-2S Milling Drilling Center（II）...
- Page 14 Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-II-01 Column JMD2S-II-02 Metric rise and down leadscrew JMD2S-II-03 Metric rise and down locking nut JMD2S-II-04 Metric rise and down leadscrew nut JMD2S-II-05 Column nut support JMD2S-II-06 Leadscrew support JMD2S-II-07 Taper pins with internal thread 6*16 6X16 JMD2S-II-08 Hexagon socket head cap screw M6*12...
- Page 15 Parts Breakdown For JMD-2S Milling Drilling Center（III）...
- Page 16 Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-III-01 The left bracket cover JMD2S-III-02 Left cover JMD2S-III-03 Longitudinal leadscrew rod bracket left sleeve JMD2S-III-04 Work table JMD2S-III-05 Metric longitudinal leadscrew nut JMD2S-III-06 Saddle JMD2S-III-07 Base JMD2S-III-08 Handwheel JMD2S-III-09 Cross bevel wedge 10 JMD2S-III-10 Longitudinal wedge locking crown bar 11 JMD2S-III-11 Small handle assembly...
- Page 17 Parts Breakdown For JMD-2S Milling Drilling Center（IV）...
- Page 18 Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-IV-01 Splash guard I JMD2S-IV-02 Splash guard II JMD2S-IV-03 Filler strip JMD2S-IV-04 Cross recessed counter head screws M4X6 JMD2S-IV-05 Dust guard JMD2S-IV-06 Dead plate JMD2S-IV-07 Cross recessed counter head screws M4X10 JMD2S-IV-08 Rise and down guideway cover JMD2S-IV-09 Magnet steel...
- Page 19 Parts Breakdown For JMD-2S Milling Drilling Center（V）...
- Page 20 Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-V-01 Tapping screw JMD2S-V-02 Change-over switch JMD2S-V-03 Emergency stop JMD2S-V-04 Lampholder JMD2S-V-05 Digital readout JMD2S-V-06 4.7K Potentionmeter JMD2S-V-07 Knob JMD2S-V-08 Electric box cover JMD2S-V-09 Tapping screw JMD2S-V-10 Hexagon headed nut JMD2S-V-11 Hexagon headed bolt M4X16 JMD2S-V-12 Power panel...
- Page 21 Accessories Part List for JMD-X2S Milling Drilling Center Part no. Descirption Size Qty. JMD2S-ACCS-01 T nut JMD2S-ACCS-02 Double end wrench S1*S2:8*10,14*17, 17*19 each 1 JMD2S-ACCS-03 L hex wrench assemble JMD2S-ACCS-04 L hex wrench S:3,4,5,6,8 each 1 JMD2S-ACCS-05 Slanting wedge JMD2S-ACCS-06 Fuse 230V/5A JMD2S-ACCS-07 Oil cup...
- Page 22 JMD-2S..1~230V,50Hz...