All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 0770 BU CD Customer Service...
EN 2 LC7.1HE LA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.3 Miscellaneous 1.1 Technical Specifications 1.2 Connection Overview Integrated clock display with wake up and message alarm 1.3 Chassis Overview (optional).
Page 3
Technical Specifications, Connections, and Chassis Overview LC7.1HE LA EN 3 Connection Overview RJ45 RJ45 RJ45 RJ45 RJ12 RJ12 RJ12 RJ12 Special tool needed Special tool needed Special tool needed Special tool needed (order via BDS) (order via BDS) (order via BDS) (order via BDS) H_17510_121.eps...
Page 4
EN 4 LC7.1HE LA Technical Specifications, Connections, and Chassis Overview - POR Signal EXT2: Video YC - In, CVBS - In/Out, Audio - In/Out - TV Clock Clock Signal - Data in Data - Data out Data 10 - +5V...
Page 5
Technical Specifications, Connections, and Chassis Overview LC7.1HE LA EN 5 10 - CLK+ Data channel 20 - Ground 11 - Shield 12 - CLK- Data channel EXT4: Cinch: Video YPbPr - In, Audio - In 13 - n.c. Gn - Video Y / 75 ohm 14 - n.c.
Page 6
EN 6 LC7.1HE LA Technical Specifications, Connections, and Chassis Overview i-BOARD POWER SUPPLY UNIT INTERFACE PANEL CONTROL PANEL SMALL SIGNAL BOARD LED PANEL H_17150_100.eps 100807 Figure 1-9 PWB/CBA locations (42" models)
• Be careful during measurements in the high voltage • Use only lead-free soldering tin Philips SAC305 with order section. code 0622 149 00106. If lead-free solder paste is required, • Never replace modules or other components while the unit please contact the manufacturer of your soldering is switched “on”.
2006 week 17). The 6 last digits contain the reduce heat. serial number. • Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to MADE IN BELGIUM MODEL 32PF9968/10 avoid mixed regimes. If this cannot be avoided, carefully 220-240V 50/60Hz clear the solder-joint from old tin and re-solder with new tin.
Mechanical Instructions LC7.1HE LA EN 9 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assy/Panel Removal •...
Page 10
EN 10 LC7.1HE LA Mechanical Instructions H_17150_107.eps 1308 07 Figure 4-2 Cable dressing (32" model)
Page 11
Mechanical Instructions LC7.1HE LA EN 11 H_17150_108.eps 130807 Figure 4-3 Cable dressing (42" model)
Page 12
EN 12 LC7.1HE LA Mechanical Instructions Service Positions Assy/Panel Removal For easy servicing of this set, there are a few possibilities 4.3.1 Rear Cover created: • The buffers from the packaging. Warning: Disconnect the mains power cord before you remove •...
Page 13
Mechanical Instructions LC7.1HE LA EN 13 4.3.5 Small Signal Board (SSB) 1. Remove the rear cover, as described earlier. 2. Refer to fig. “SSB removal” below. 3. Disconnect all cables [a] on the SSB. 4. Remove the screws [b] that hold the SSB.
Page 14
EN 14 LC7.1HE LA Mechanical Instructions 4.3.7 DC-DC converter for i-Board (26" optional) 4.3.9 Main Supply Panel 1. Remove the rear cover, as described earlier. 1. Refer to next figures. 2. Refer to fig. “DC-DC converter for i-Board removal” below.
Page 15
Mechanical Instructions LC7.1HE LA EN 15 4.3.10 Clock Board (optional) 1. Remove the rear cover, as described earlier. 2. Optionally remove the Main Supply panel, as described earlier. 3. Optionally remove the Small Signal Board, as described earlier. 4. Optionally remove the DC-DC converter for i-Board, as described earlier.
Page 16
EN 16 LC7.1HE LA Mechanical Instructions 4.3.11 LCD Panel 26" models 7. Do NOT forget to unplug the LVDS connector [e] from the SSB. Important: Be careful, as this is a very fragile connector! 1. Remove the rear cover, as described earlier.
Page 17
Mechanical Instructions LC7.1HE LA EN 17 4.3.12 LCD Panel 32" models 7. Remove screws [1] that hold the mid-range speakers and remove those. 8. Remove screws [2] that hold the central sub-frame. 1. Remove the rear cover, as described earlier.
Page 18
EN 18 LC7.1HE LA Mechanical Instructions 4.3.13 LCD Panel 42" model 7. Remove screws [1] that hold the support bars and remove those. 8. Remove screws [2] from the speaker frames and remove 1. Remove the rear cover, as described earlier.
Page 19
Mechanical Instructions LC7.1HE LA EN 19 Set Re-assembly To re-assemble the whole set, execute all processes in reverse order. Notes: • While re-assembling, make sure that all cables are placed and connected in their original position. See figure “Cable dressing”.
Instructions on how to enable the CSM can be given by telephone by either the dealer or the P3C (Philips Customer Care Centre). The CSM displays diagnosis information, which the customer can forward to the dealer/P3C. In CSM mode, Display Option “CSM”, is displayed in the top right corner of the screen.
Page 21
Service Modes, Error Codes, and Fault Finding LC7.1HE LA EN 21 During this algorithm, the NVM-content must be filtered, because several items in the NVM are TV-related and not SSB- related (e.g. Model and Prod. S/N). Therefore, “Model” and “Prod. S/N” data is changed into “See Type Plate”. In case a call centre or consumer reads “See Type Plate”...
Page 22
EN 22 LC7.1HE LA Service Modes, Error Codes, and Fault Finding How to Exit 5. OP (Option Bytes). Used to read-out the option bytes. See Switch the set to STANDBY by pressing the mains button on “Options” in the Alignments section for a detailed the remote control transmitter or on the television set.
Page 23
Service Modes, Error Codes, and Fault Finding LC7.1HE LA EN 23 5.3.4 Customer Service Mode (CSM) (*) If an NVM IC is replaced or initialised, this data must be re- written to the NVM. ComPair will foresee in a possibility to do this.
Page 24
Introduction Introduction Error codes are required to indicate failures in the TV set. In ComPair (Computer Aided Repair) is a Service tool for Philips principle a unique error code is available for every: Consumer Electronics products. and offers the following: •...
Page 25
Service Modes, Error Codes, and Fault Finding LC7.1HE LA EN 25 Table 5-2 Error code overview The Blinking LED Procedure Error Description Item Remarks 5.6.1 Introduction code No error. The software is capable of identifying different kinds of errors. DC Protection of speakers.
Page 26
EN 26 LC7.1HE LA Service Modes, Error Codes, and Fault Finding Table 5-3 NVM editor overview Description .ADR 0x000A Existing value .VAL 0x0000 New value .Store Store? 5.8.2 Load Default NVM Values It is possible to download default values automatically into the NVM in case a blank NVM is placed or when the NVM first 20 address contents are “FF”.
Page 27
Service Modes, Error Codes, and Fault Finding LC7.1HE LA EN 27 AC ON Start Up (1) +5VSTBY to be measured +5VSTBY & +3V3STBY Available (1) at PDTC114ET (item 7322) RENEAS POR by +3VSTBY (2) (2) to be measured at pin 4...
Page 28
EN 28 LC7.1HE LA Service Modes, Error Codes, and Fault Finding Start SEMISTANDBY/ STANDBY Mute Audio BL_ADJ stop dimming (PWM duty cycle 100%) BL_ON_OFF = LOW Wait 300ms 300ms Switch OFF LVDS 20ms Wait 20ms LCD_PWR_ON = LOW Software Shutdown:...
Page 29
Service Modes, Error Codes, and Fault Finding LC7.1HE LA EN 29 Power Down INT: AC OFF or Transient INT Start Avoid false trigger Poll the Power Down INT for 5 times Mute Audio & VIdeo Notes: 1. Power Down INT will be based on fall edge triggering 2.
Page 30
EN 30 LC7.1HE LA Service Modes, Error Codes, and Fault Finding Personal Notes: E_06532_012.eps 131004...
Block Diagrams, Test Point Overviews, and Waveforms LC7.1HE LA Block Diagram Video VIDEO B03A TUNER IF & DEMODULATOR B04B VIDEO PROCESSOR 7202 +5VS SVP CX32-LF +VTUN 7113 TDA9886T/V4 1101 TD1318S/A DEMODULATOR 1102 SUPPLY 7114 VIF1 VIF1 4120 MAIN IF_ATV SOUND TRAPS...
Block Diagrams, Test Point Overviews, and Waveforms LC7.1HE LA Block Diagram Control & Clock Signals CONTROL & CLOCK SIGNALS B04B VIDEO PROCESSOR 7202 7204 IS42S16400D-6TL SVP CX32-LF TXCLKn TXCLKn1 DRAM 1Mx16x4 TO DISPLAY TXCLKP TXCLKP1 (LVDS) DQ(0-31) 7203 7206 7205...
Alignments LC7.1HE LA EN 79 8. Alignments Index of this chapter: For the tuner no alignment is necessary, as the AGC alignment 8.1 General Alignment Conditions is done automatically (standard value: “15”), even during 8.2 Hardware Alignments analogue reception, however in case of problems use the 8.3 Software Alignments...
Page 80
Required Software Versions Be aware that the software used in these iTV sets is NOT similar to the software in Mainstream LCD-TVs. Ensure that the latest iTV software is used in these sets (available on the Philips Service web site).
Page 81
Alignments LC7.1HE LA EN 81 Option Settings 8.5.2 How To Set Option Codes When the NVM is replaced, all options will require resetting. To 8.5.1 Introduction be certain that the factory settings are reproduced exactly, you must set all option numbers.
Page 82
EN 82 LC7.1HE LA Alignments Table 8-6 Option codes at bit level (OP3-OP7) Option Byte & Bit Dec. Value Option Name Description Byte OP3 Bit 7 (MSB) CVI2 ON=CVI1 (YPbPr) (For ROW) Bit 6 Reserved Not Used (Reserved) Bit 5...
Page 83
TV set to the The Philips Wireless Smart-Loader is an installation tool Wireless Smart-Loader (100 = fully loaded). especially designed for easy and fast installation of Philips TV TO SMARTLOADER -------- ## Institutional TV's. The Wireless Smart-Loader 22AV1120/00 is –...
See LC7.1E LA manual for detailed called “ME7”. information. The LC7.1HE LA chassis is derived from the LC7.1E LA • Figures can deviate slightly from the actual situation, due chassis: it uses an analogue only derived SSB from this to different set executions.
Customer Service Mode the customers wishes CVBS Composite Video Blanking and LATAM LATin AMerica Synchronisation LC07 Philips chassis name for LCD TV 2007 CVBS-MON CVBS monitor signal project CVBS-TER-OUT CVBS terrestrial out Liquid Crystal Display Component Video Input Light Emitting Diode...
Page 86
4.406250 MHz and 4.250000 MHz Sound Intermediate Frequency SMPS Switch Mode Power Supply SouND SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace SRAM Static RAM Small Signal Board STBY Stand-by SVHS Super Video Home System Sub Woofer / SoftWare...
Spare Parts List LC7.1HE LA EN 87 10. Spare Parts List Sets Listed per Model Number (CTN) 8735 3139 131 08671 Cable 4p/480 1000/2ft 5212 2422 264 00617 Loudsp. 6Ω 15W L 8C01 3139 131 08541 Cable 9p/220/9p Bk 8G51 3139 131 08282 LVDS 30p/180/30p 26HF5445/10 (Alt.
Need help?
Do you have a question about the LC7.1HE LA and is the answer not in the manual?
Questions and answers