Philips LC7.1HE LA Service Manual page 83

8.6 Wireless Smart-Loader (22AV1120/00)
8.6.1 iTV Installation Tool
The Philips Wireless Smart-Loader is an installation tool
especially designed for easy and fast installation of Philips
Institutional TV's. The Wireless Smart-Loader 22AV1120/00 is
compatible with the Wired Smart-Loader version 22AV1015/
01.
Instruction for use
Make sure that the 3 R6/AA sized batteries are placed correctly
in the backside compartment of the Wireless Smart-Loader.
Turn the power switch to "on" at the left side of the Wireless
Smart-Loader. A green LED lights up when any button is
pressed, indicating that batteries are in operational condition.
When the red LED lights up, the batteries must be replaced.
Note:
• Only the wireless method can be used for the TV sets
described in this manual.
• The wired method, in which an accessory cable must be
connected between the Wireless Smart-Loader and the TV
set, is not an functional option for the TV sets described in
this manual.
Figure 8-1 Wireless Smart-Loader 22AV1120/00
The installation procedure consists of three steps:
1. Chose the master TV.
2. Program the Wireless Smart-Loader.
3. Install TV set(s) of the same type with the Wireless Smart-
Loader. (step 3 can be repeated on as many TV sets as
required).
8.6.2 Choosing a Master TV
The master TV set is the TV whose installation set-up has to be
copied into other TV sets of the same type.
8.6.3 Programming the Wireless Smart-Loader
This step has to be done only once, or any time the installation
set-up stored in the Wireless Smart-Loader has to be changed.
• Press the "MENU" Key on the Wireless Smart-Loader.
The following menu appears:
– SMARTLOADER
– SMARTLOADER TO TV >
– TV TO SMARTLOADER >
E_14520_077.eps
070806
Alignments LC7.1HE LA
Highlight "TV TO SMARTLOADER".
• Press the right cursor key on the Wireless Smart-Loader.
– A number from 1-100 is displayed, indicating the data
transfer completed percentage, from the TV set to the
Wireless Smart-Loader (100 = fully loaded).
TV TO SMARTLOADER -------- ##
– When the data transfer is completed, ## is "100", the
following menu appears for 3 seconds:
DONE >
– Now the Wireless Smart-Loader is programmed and
can be used to install other TV sets of the same type.
8.6.4 Installing a TV with the Wireless Smart-Loader
Use a Wireless Smart-Loader programmed with the settings
from a master TV of the same type.
• Turn on the TV, press the "MENU" Key on the Wireless
Smart-Loader.
The following menu appears:
– SMARTLOADER
– SMARTLOADER TO TV >
– TV TO SMARTLOADER >
Highlight "SMARTLOADER TO TV".
• Press the right arrow key on the Wireless Smart-Loader.
– A number from 1-100 is displayed, indicating the data
transfer completed percentage, from the Wireless
Smart-Loader to the TV (100 = fully loaded).
SMARTLOADER TO TV ||| -------##
– When data transfer is completed, ## = "100",
the following menu appears for 3 seconds:
– GOODBYE >
– The TV set goes to stand-by now and will start up
automatically.
The TV set is now installed and ready for use.
8.6.5 Problems and Solutions:
• The message "WRONG VERSION" appears on the
screen.
– The Wireless Smart-Loader contains a master TV
installation set-up not compatible to the TV set to be
set-up. Reprogram the Wireless Smart-Loader from a
master TV set whose software version is compatible
with the software version of the TV set to be set-up.
• TV does not respond to the Wireless Smart-Loader.
– Check if the green LED lights up on the Wireless
Smart-Loader when any button is pressed, and check
if the batteries are in a good condition. When the red
LED lights up, the batteries must be replaced.
– Place the Wireless Smart-Loader closer to the infra red
receiver of the TV set and try again.
Tips:
• Write the software version and the type of the relevant
master TV set on the sticker, attached to the backside of
the Wireless Smart-Loader.
• Without batteries, the Wireless Smart-Loader retains the
stored information for ten years.
Note:
• Before the Wireless Smart-Loader is stored for a long
period of time, take out the batteries to prevent the contacts
from corrosion.
• Wired Smart-Loading method can not be used on the TV
sets described in this manual.
8. EN 83