Advertisement
PROPER USE GUIDELINES
Cumulative trauma disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional
use and low-volume applications. A wide selection of powered application equipment is available for extended-use production operations.
1. INTRODUCTION
These instructions deal with the safety, installation, operation and maintenance of the Pistol Grip Pneumatic
Handle Assembly 58075-1 (Figure 1).
Pistol Grip Pneumatic Handle Assembly 58075-1 accepts interchangeable terminating heads that terminate
wires in connectors. To ensure accurate termination of wires, setup adjustments, and head maintenance, refer
to the instructions packaged with the terminating head.
NOTE
Dimensions in this instruction sheet are in millimeters with [inches in brackets]. Figures are for reference only and are not
drawn to scale.
Reasons for reissue of this instruction sheet are provided in section 8, REVISION SUMMARY.
© 2021 TE Connectivity Ltd. family of companies.
All Rights Reserved.
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
Pistol Grip Pneumatic
Handle Assembly 58075-1
Figure 1: Pistol Grip Pneumatic Handle Assembly 58075-1
1
Air cylinder
2
Body
3
Key (visible on this side)
4
Trigger
5
Handle
6
Air tube
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
Instruction Sheet
408-6789
Rev F
28 SEP 2021
1 of 7
Advertisement
Table of Contents
Related Manuals for TE Connectivity 58075-1
Summary of Contents for TE Connectivity 58075-1
- Page 1 1 of 7 For latest revision and Regional Customer Service, All Rights Reserved. visit our website at www.te.com. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
- Page 2 408-6789 2. DESCRIPTION The pneumatic handle assembly features a molded nylon handle with a trigger and an air tube. The handle holds an air cylinder with a key that retains the terminating head in the body and allows the head to be rotated (Figure 1).
- Page 3 408-6789 3. INSTALLING AND REMOVING THE HEAD DANGER To avoid personal injury, always disconnect the handle assembly from the air supply when installing or removing the head. 1. Disconnect or lock out the tool from its air supply. 2. Position the blade tip of a screwdriver between the shoulder of the key and the handle assembly body. Pry and remove the key (Figure 3).
- Page 4 408-6789 4. SETUP Use a regulator-filter-lubricator unit with the lubricator adjusted to the minimum setting (Figure 4). Figure 4: Regulator-filter-lubricator unit Air supply Filter and moisture separator Regulator Lubricator To handle assembly Use quick-disconnect fittings to connect the tool to the air supply. If not using quick-disconnect fittings, provide a pneumatic lock-out on the air line that bleeds air after it is turned off.
- Page 5 408-6789 6. MAINTENANCE AND INSPECTION DANGER To avoid personal injury, always disconnect the handle assembly from the air supply when performing maintenance or inspection procedures. Each handle assembly is inspected before shipment. Inspect the handle assembly immediately upon arrival at the facility of use to ensure that it has not been damaged during shipping.
- Page 6 Shop TE link at the top of the page. Call 800-522-6752. Write to: CUSTOMER SERVICE (038-035) TE CONNECTIVITY CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 For customer repair services, call 800-522-6752. 6 of 7 Rev F...
- Page 7 408-6789 8. REVISION SUMMARY Revisions to this instruction sheet include: Removed CE label from Figure 5. Reformatted to match current standard for instruction sheets. 7 of 7 Rev F...
Need help?
Do you have a question about the 58075-1 and is the answer not in the manual?
Questions and answers