Related Manuals for Z GRILLS MULTITASKER 11002B
Summary of Contents for Z GRILLS MULTITASKER 11002B
- Page 1 WOOD PELLET GRILLS ZPGD-1100 2B OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: support@zgrills.com WEBSITE: www.zgrills.com VN122020...
-
Page 3: Table Of Contents
CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING GRILL CONTROL BOARD INTRODUCTION Z GRILLS SUPPORT 3-Y LIMITED WARRANTY... - Page 4 SAVE THIS MANUAL FOR FUTURE REFERENCE...
-
Page 5: Important Safety Info
IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. - Page 6 DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use.
- Page 7 There is no guarantee that other brands of pellets are suitable for use in Z GRILLS. And Z GRILLS assumes no liability for any loss, damage or injury caused by the use of any other brands of pellets.
-
Page 8: Component List
COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Chamber Lid Front Foot pad Hopper Assembly Wheels(with brake) Grill Chamber Assembly Wheels(without brake) Grease Drain Pan Cutting Board Front Shelf Left Bracket Heat Baffle Front Shelf Right Bracket Hopper Lid Front Shelf Hopper Burner Assembly Tube Sealing Upper Hopper Safety Grate Porcelain Cooking Grates... - Page 9 HARDWARE PACKAGE LIST ITEM DESCRIPTION ITEM DESCRIPTION Phillips Head Screw Phillips Head Lock Screw 8-32×3/8 1/4-20×5/8 Phillips Head Screw Wrench 1/4-20x1-3/5 Handle Base Tube Screwdriver...
-
Page 10: Assembly Instructions
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM： HOPPER BURNER ASSEMBLY:... - Page 11 1.MOUNTING THE BODY FRAME 1.Unpack all the items, including the parts packed in the Grill Chamber (3). Turn the body side and place upon the original Styrofoam packing material from the carton. (CAUTION: Grill is heavy and requires two people to lift.) 2.Insert Screws (DD) through Rear Guide Track (16) into the Grill Chamber Assembly (3).
- Page 12 4.Take the Rear & Front Legs (20)(21) and use the Screws (AA) to assemble the grill body through the holes. As shown. 5.Attach the Back Plate (22) on Rear Leg (20) and Front Leg (21) by using the Screws (AA). The two positions are installed in the same manner, as shown.
- Page 13 6.Attach the Front Plate (23) on Rear Leg (20) and Front Leg (21) by using the Screws (AA). The two positions are installed in the same manner, as shown. 7.Assemble the wheels (with brake)(26) & the wheels (without brake)(27) on the Legs (20)(21) respectively.
- Page 14 2.ATTACHING THE CHAMBER LID HANDLE From the inside of the raised lid, push the Screws (BB) through the Handle Base Tube (CC) and then through the lid (1) and Handle Base (13). Handle should sit inside the depression in the guide. Thread Screws (BB) into Handle (14) and tighten with Screwdriver (FF). 3.ATTACHING THE SIDE HANDLE Remove the Screws assembled on the Side Handle (15).
- Page 15 4.FRONT SHELF ASSEMBLY 1.Insert Screws (AA) through the Front Table Left Bracket (5) and into the Front Shelf (7). 2.Repeat Steps 1 for Front Table Right Bracket (6). Use the screwdriver (FF) to tighten. 5.ATTACHING THE FRONT SHELF Insert Screws (AA) through the Front Table Left & Right Brackets (5)(6) into the Grill Chamber Assembly (3), as shown.
- Page 16 6.ATTACHING HEAT BAFFLE Attaching the Heat Baffle (29) on the Firepot. 7.POSITIONING THE GREASE DRAIN PAN Install the Grease Drain Pan (4) over the Heat Baffle (29) facing downward to fit onto the locating brackets so that the grease can flow into the Grease Box.
- Page 17 8.ATTACHING COOKING GRATE AND WARMING RACK Attaching the Porcelain Cooking Grates (9) and Warming Rack (10) in the Chamber. 9. ATTACHING THE CORD HOOK Insert Screws (DD) through the Cord Hook (46) into the Hopper Assembly, as shown. Use the screwdriver (FF) to tighten.
- Page 18 10.BOX HANDLE ASSEMBLY Insert Screws (DD) through the Grease Box (19) into the Box Handle (18), as shown. Use the screwdriver (FF) to tighten. 11.POSITIONING THE GREASE BOX Insert the Grease Box (19) into the Guide-track groove.
- Page 19 12.POSITIONING THE CUTTING BOARD Place Cutting Board (28) on the recess of the hopper lid.
-
Page 20: Initial Firing Instructions
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Warming Rack, Grease Drain Pan and Heat Baffle from the interior of the grill. -
Page 21: Subsequent Start-Up
Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem. -
Page 22: Operating Tips
OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open. -
Page 23: Maintenance & Cleaning
2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish. - Page 24 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
-
Page 25: Troubleshooting
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet. - Page 26 Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
-
Page 27: Grill Control Board Introduction
GRILL CONTROL BOARD INTRODUCTION CONTROL PANEL Button Functions: - POWER BUTTON Press the POWER BUTTON to power ON the grill, once the grill is connected to a power source: POWER BUTTON is pressed down, the digital LCD screen will flash a time and off. The power is connected to grill, but Motor, fan and hot rod are kept off. - Page 28 - START After the grill is connected to power, press START button to activate the startup process of grill, which ignites the pellet automatically. Press and hold in 3 seconds to activate the grill shutdown process. The fan will be kept running to burn pellets up and cool the grill down.
- Page 29 - KEEP WARM Press button, the grill will be run as target temperature setting in 165F. Press twice, the grill will be back to last setting. - SUPER SMOKE Press button to allow grill to generate super smoke. press twice to return the last setting of grill.
- Page 30 - ACTUAL TEMPERATURE INDICATOR The indicator shows temperature in grill, which is in unit of F. - PROBE INDICATOR The indicator shows target temperature setting; When button of “Select and push” is pressed, it is flashing. The probe is ready for setting, which fault setting is room temperature. The setting will be increased or decreased by turning button in clockwise or anticlockwise.
- Page 31 GRILL ELECTRIC SYSTEM Inputs: Input 1 - 120V 2A 60 Hz Input 2 - Probes- P1 and P2 Input 3 – Grill temperature sensor Outputs: Output 1 - Hot Rod Output 2 - Auger Motor Output 3 - Fan Motor Output 4 - Probe and grill temperature display All temperatures are displayed in Fahrenheit...
- Page 32 Operation Flow: Step 1. The power cord is connected. At this point, the LCD display is powered off. Motor, fan and hot rod are kept off. Step 2. Press power button, which powers the grill on. LCD display is till turned off and press the start button the grill will begin its Startup Cycle.
- Page 33 SET THE DESIRED GRILL TEMPERATURE Use temperature dial to set desired temperature. The temperature settings of the grill start from SMOKE to HIGH. At those settings, the auger motor is running, and feeds pellets into the fire pot according to set temperature.
-
Page 34: Z Grills Support
Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase... -
Page 35: 3-Y Limited Warranty
Z GRILLS, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...