Related Manuals for Z GRILLS ZPG-550B
Summary of Contents for Z GRILLS ZPG-550B
- Page 1 WOOD PELLET GRILLS ZPG-550B OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: support@zgrills.com WEBSITE: www.zgrills.com VN08012019...
-
Page 3: Table Of Contents
CONTENTS WARNINGS COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY... - Page 4 SAVE THIS MANUAL FOR FUTURE REFERENCE...
-
Page 5: Warnings
NOT unplug the power cord. DO NOT throw water on it. DO NOT try to smother the fire. Clean and maintain your grill after each use. We suggest that you use Z GRILLS BBQ WOOD PELLETS, which are specifically made to work in our grills. DO NOT use your grill on rainy days. -
Page 6: Component List
COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Grill Chamber Assembly Digital Control Hopper Assembly Hopper Guard Warming Rack Auger Drive Motor Porcelain Grills Auger Nylon Ring Grease Drain Pan Auger Heat Baffle Foam Glue RTD Temperature Probe Hot Rod (Ignitor) RTD Guard Feeder Assembly Lid Handle Handle Guide... -
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM Hopper Burner Assembly：... - Page 8 1. MOUNTING THE BODY FRAME TO THE CHAMBER 1. Unpack all the items, including the parts packed in the Grill Chamber (1). Turn the body upside down and place upon the original Styrofoam packing material from the carton. (CAUTION: Grill is heavy and requires two people to lift.) 2.
- Page 9 2.INSTALLING THE CHAMBER HANDLE TO THE LID: 1. Lift the Grill Assembly, turn, and place on the floor. 2. From the inside of the raised lid, push the Blots (H) through the Washers (D) and then through the lid and Handle Guide (10). Handle should sit inside the depression in the guide. Thread Bolts (H) into Handle (9) and tighten with Wrench (B).
- Page 10 4.INSTALLING THE HEAT BAFFLE: Place the lower bracket of the Heat Baffle (6) into the groove of the feeder. 5.INSTALLING THE GREASE DRAIN PAN: Install the Grease Drain Pan (5) over the Heat Baffle (6) facing downward to fit onto the locating brackets so that the grease can flow into the Grease Drain Tube.
- Page 11 6.INSTALLING THE COOKING GRATE AND WARMING RACK: Install the Porcelain Cooking Grate (4) and Warming Rack (3) into the Chamber. 7.HANG ON THE GREASE BUCKET: Located the Grease Drain Tube which is on the right side of the Chamber, then hang the Grease Bucket (16) on the hook.
-
Page 12: Initial Firing Instructions
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. -
Page 13: Subsequent Start-Up
Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem. -
Page 14: Operating Tips
OPERATING TIPS 1.like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open. -
Page 15: Maintenance & Cleaning
2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish. - Page 16 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
-
Page 17: Troubleshooting
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet. - Page 18 Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
-
Page 19: Digtal Thermostat Control Wiring Diagram
DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM... -
Page 20: Z Grills Support
Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase... -
Page 21: 3-Y Limited Warranty
Z GRILLS 3 YEAR LIMITED WARRANTY Z GRILLS, Inc. provides a 3 years warranty from the date of purchase by the original owner. This warranty applies to defects in all materials and workmanship. During the warranty period, Z GRILLS, Inc. will at its option repair or replace defective parts or units.