Advertisement
Table of Contents
- 1 Table of Contents
- 2 Important Safety Info
- 3 Component List
- 4 Assembly Instructions
- 5 Initial Firing Instructions
- 6 Subsequent Start-Up
- 7 Operating Tips
- 8 Maintenance & Cleaning
- 9 Troubleshooting
- 10 Digital Thermostat Control Wiring Diagram
- 11 Z Grills Support
- 12 3-Y Limited Warranty
- Download this manual
Advertisement
Table of Contents
Related Manuals for Z GRILLS ZPG-700D3
Summary of Contents for Z GRILLS ZPG-700D3
- Page 1 WOOD PELLET GRILLS ZPG-700D3/ZPG-700D4E OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: support@zgrills.com WEBSITE: www.zgrills.com VN092020...
-
Page 2: Table Of Contents
CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY... - Page 3 SAVE THIS MANUAL FOR FUTURE REFERENCE...
-
Page 4: Important Safety Info
IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area. - Page 5 DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use.
- Page 6 There is no guarantee that other brands of pellets are suitable for use in Z GRILLS. And Z GRILLS assumes no liability for any loss, damage or injury caused by the use of any other brands of pellets.
-
Page 7: Component List
COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Grill Chamber Assembly Firepot Assembly Hopper Bottom Assembly Feeder Assembly Body Frame Hopper Burner Gasket Thermal Baffle Heat Baffle Power Cord Grease Drain Pan Cable Clip Warming Rack Beam Porcelain Grills Magnet Left Door Upper Pivot Hinge Assembly Bottom Pivot Lid Handle... - Page 8 HARDWARE PACKAGE LIST ITEM DESCRIPTION ITEM DESCRIPTION Bolt 5/32-32×5 Hopper Burner Handle Open End Wrench Bolt 1/4-20×12 Hexagon Bolt 1/4-20×12 Bolt 5/32-32×6 Gasket (Ø18*Ø6.5*2mm) Hexagon Kep Nut 5/32-32 Hexagon Nut 1/4-20 Screwdriver Gasket (Ø12*Ø4.2*1.0mm)
-
Page 9: Assembly Instructions
ASSEMBLY INSTRUCTIONS PARTS DIAGRAM HOPPER BURNER ASSEMBLY... - Page 10 BODY FRAME ASSEMBLY 1.ASSEMBLING OF BOTTOM BASE 1.Turn the Platform (49) upside down. Install the wheels (without brake)(47) in the screw holes. Tighten with wrench (H). Note: The 2 wheels (without brake)(47) should be installed on the side near the magnet base. Install the wheels (with brake)(48) into the screw holes. Tighten with wrench (H).
- Page 11 2.MOUNTING THE BODY FRAME 1.Secure Left Plate (39) on the Platform (49) with Bolt (B). 2.Secure Right Plate (44) on the Platform (49) with Bolt (B). 3.Secure Back Plate (43) on the Platform (49) with Bolt (B) and connect to Left Plate (39) and Right Plate (44).
- Page 12 3.ASSEMBLING OF HOPPER Insert Hopper Top Assembly I (46) into Hopper Bottom Assembly (2), align the holes. Make sure hopper opens to the front (control side). Insert the Bolts (I) through the holes in the Hopper and Kep Nuts (J), then open the Hopper Lid and tighten it from inside. The four sides are installed in the same way.
- Page 13 4.POSITIONING THE CHAMBER ON THE BODY FRAME Lift up the Chamber (1) on the Body Frame (3). Make sure that the Chamber (1) is inside the left and right plate of the Frame (3). Align the Chamber holes with the plate holes and secure with Bolt (B).
- Page 14 6.MOUNTING THE HOPPER TO THE CHAMBER 1.Remove the 4 Gaskets and Bolts from the Hopper, open the Lid, insert the Hopper into the Chamber, then using these Bolts and Gaskets install it in sequence from inside. 2. Locate the RTD plug-in connector coming from the mounted RTD inside the grill frame. Connect this with the mating connector located on the outside of the hopper burner assembly.
- Page 15 8.ATTACHING THE CHAMBER DOOR HANDLE Insert Hexagon Bolt (C) through Gasket (D), Lid (9) and Handle Base (12) directly to the handle (11) and tighten up. Do not over-tighten. 9.ATTACHING THE SMOKE STACK AND CHIMNEY CAP 1.Install the Chimney Cap (14) to Smoke Stack (15).Note that the Chimney Cap (14) is vertical and then tighten.
- Page 16 10.POSITIONING THE DOOR HANDLE Align the holes in the Left Door (37) with the holes in the Handle (41). Insert Hexagon Bolt (C) through the Gasket (D), Left Door (37) and Door Handle Base (42) to Door Handle (41). Use the wrench to tighten.
- Page 17 12.POSITIONING THE HEAT BAFFLE Position The Heat Baffle (5) on the locating brackets which is on the inside walls of the Grill. The notched legs should be facing downward. Slide Heat Baffle (5) to the right to lock in place. 13.POSITIONING THE GREASE DRAIN PAN Position The Grease Drain Pan (6) over the Firepot (27) by fitting over the bracket on the left side of grill wall.
- Page 18 14.POSITIONING THE PORCELAIN GRILL AND WARMING RACK Position the Porcelain Grill (8) inside the chamber. Install the Warming Rack (7) on the rack supports inside the chamber. 15.HANG ON THE GREASE BUCKET Locate the Grease Drain Tube which is on the right side of the chamber, then hang the Grease Bucket (17) on the hook.
-
Page 19: Initial Firing Instructions
Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. -
Page 20: Subsequent Start-Up
Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem. -
Page 21: Operating Tips
OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open. -
Page 22: Maintenance & Cleaning
2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish. - Page 23 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
-
Page 24: Troubleshooting
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet. - Page 25 Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
-
Page 26: Digital Thermostat Control Wiring Diagram
DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Usage of the Meat Probe Put the plug of the Meat Probe into the control panel (PROBE1 or PROBE2) Insert the Probe into the food to measure the temperature The P1 temperature of the control panel is displayed as the temperature of PROBE1, while the P2 temp is displayed as the temp of PROBE2... -
Page 27: Z Grills Support
Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase... -
Page 28: 3-Y Limited Warranty
Z GRILLS, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...