Digital Watchdog DWC-V6263TIR Quick Start Manual

Quick Start Guide
DW® Universal HD over Coax®
vandal dome cameras
DWC-V6263TIR
WHAT'S IN THE BOX
Mounting
Torx Wrench DC Plug Cable
Star wrench 1
template
Torx Wrench DC Plug Cable Test Video Cable
Screws and
DC plug
Sunshield cover &
1 plastic anchors
Torx Wrench DC Plug Cable Test Video Cable
cable
Torx Wrench DC Plug Cable Test Video Cable - 4pcs
Template Sheet Manual
Moisture
Quick set up absorber and Screw &
1
Template Sheet Manual
guide absorber guide
(recommended)
Screw & Moisture absorber &
Template Sheet Manual Screw &
Template Sheet Manual
Test video
1
cable
Sunshield cover &
DC Plug Cable Test Video Cable
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources.
2. Search your product by entering the part number in
the 'Search by Product' search bar. Results for
Screw & Moisture absorber &
applicable part numbers will populate automatically
Manual
Absorber Guide
based on the part number you enter.
3. Click 'Search'. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for initial
setup. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
STEP 1 – PREPARING TO MOUNT THE CAMERA STEP 1 – PREPARING TO MOUNT THE CAMERA
1. The mounting surface must withstand five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or
fire.
3. Install the moisture packet in the base of the camera's lens.
a. Remove the moisture absorber from the packaging.
b. Cut the card and folder along the dotted line.
c. Place the moisture absorber behind the camera's lens module. See drawing for more information.
NOTE:
Torx Wrench DC Plug Cable WARNING:
Test Video Cable
Sunshield cover &
Test Video Cable
1
Sunshield cover &
Screw &
Template Sheet Manual
4. Detach the camera's dome cover by loosening the four (4) screws on
1 set
Sunshield cover & each side of the dome.
Screw & Moisture absorber &
5. Remove the dome protection film before placing the dome back on the
Absorber Guide
camera base.
Moisture absorber &
1
Absorber Guide
6. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
Moisture absorber &
Absorber Guide
Absorber Guide
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.
12VDC ONLY!
CAUTION! The camera supports DC power supply only
digital-watchdog.com
The camera will generate enough heat to dry moisture
during operation. In most cases it will not need the
moisture absorber for more than the first day. In cases
where the camera can experience a moisture issue,
users must keep the moisture absorber in the camera.
The moisture absorber has an approximately 6-month
life cycle, varying depending on the environment.
Sunshield cover &
It is highly recommended that you install the moisture
absorber when mounting the camera. The moisture
absorber prevents moisture from being captured
inside the camera's housing, which may cause image
performance issues and damage the camera.
Moisture absorber &
Absorber Guide
Power Requirements
Please cut the card type absorber along
a dotted line, overlap and attach them
according to the direction of the arrow.
Protective
sheet
Protective
film
Power Consumption
DC12V (LED off): 1.86W
DC12V (LED on): 3.6W
Quick Start Guide