Page 1
All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corporation without notice. Please review the latest information published by Renesas Electronics Corporation through various means, including the Renesas Electronics Corporation website (http://www.renesas.com).
Page 2
Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics.
Page 3
RSK+. Renesas expressly disclaims all such warranties. Renesas or its affiliates shall in no event be liable for any loss of profit, loss of data, loss of contract, loss of business, damage to reputation or goodwill, any economic loss, any reprogramming or recall...
Page 4
The following documents apply to the RX65N Group, RX651 Group. Make sure to refer to the latest versions of these documents. The newest versions of the documents listed may be obtained from the Renesas Electronics Web site.
Page 5
Digital-to-Analog Converter Dual In-line Package Direct Memory Access DMAC Direct Memory Access Controller Do Not Fit E1/E2 Lite Renesas On-chip Debugging Emulator EEPROM Electronically Erasable Programmable Read Only Memory Electromagnetic Compatibility Electrostatic Discharge General PWM Timer C (IIC) Philips™ Inter-Integrated Circuit Connection Bus...
Jun 30, 2016 1. Overview Purpose This RSK+ is an evaluation tool for Renesas microcontrollers. This manual describes the technical details of the RSK+ hardware. The Quick Start Guide and Tutorial Manual provide details of the software installation and debugging environment.
Power-Up Behaviour When the RSK+ is purchased, the RSK+ board has the ‘Release’ build of the example tutorial software pre- programmed into the Renesas microcontroller. Please consult the ‘Renesas Starter Kit+ Code Generator Tutorial Manual’ for further information of this example.
RSK+RX65N 3. Board Layout Board Dimensions Figure 3-2 below gives the board dimensions and connector positions. All the through-hole connectors are on a common 2.54mm pitch grid for easy interfacing. Corners x 4 3.0 mm radius Ethernet LED(Speed) PMOD1 ETHERNET0 (Ethernet Connector) RL78/G1C Func...
RSK+RX65N 3. Board Layout Component Placement Figure 3-3 below shows placement of individual components on the top-side PCB – bottom-side component placement can be seen in Figure 3-4. Component types and values are shown on the board schematics. RCAN C110 SDSI R211 R198...
RSK+RX65N 4. Connectivity 4. Connectivity Internal RSK+ Connections The diagram below shows the RSK+ board components and their connectivity to the MCU. DC PWR IN (5V) USB to Serial Regulator IC VBUS 5V Application Board Interface RL78/G1C (Application Header) E1/E2-Lite Debug Interface Function LCD Direct Drive Header (TFT) USB0 (Function/Host)
RSK+RX65N 4. Connectivity Debugger Connections Figure 4-2 below shows the connections between the RSK+, E1/E2 Lite debugger and the host PC. 5 V External Power LCD Display User Interface Cable USB Cable E1 Emulator E2 Emulator Lite CPU Board Host PC Figure 4-2: Debugger Connection Diagram R20UT3558EG0100 Rev.
RSK+RX65N User Circuitry 5. User Circuitry Reset Circuit A reset control circuit is fitted to the RSK+ to generate the required reset signal, and is triggered from the RES switch. Refer to the RX65N Group, RX651 Group User’s Manual: Hardware for details regarding the reset signal timing requirements, and the RSK+ schematics for information regarding the reset circuitry in use on the board.
RSK+RX65N User Circuitry Potentiometer A single-turn potentiometer is connected as a potential divider to analog input AN000, pin 141. The potentiometer can be used to create a voltage between Board_3V3 and ground. Refer to the maker site for specification of the potentiometer (VISHAY with part number TS53 series). The potentiometer offers an easy method of supplying a variable analog input to the microcontroller.
User Circuitry USB Serial Port A USB serial port is implemented in a Renesas low power microcontroller (RL78/G1C) and is connected to the RX65N Serial Communications Interface (SCI) module. Multiple options are provided to allow the selection of the connected SCI2 port. Connections between the USB to Serial converter and the microcontroller are listed in Table 5-6 below.
User Circuitry Ethernet When running any Ethernet software, a unique MAC address should be used. A unique Renesas allocated MAC address is attached to the RSK+RX65N PCB as a sticker, and should be always be used with this device ensured to ensure full compatibility when using other Renesas hardware on a common Ethernet connection.
LCD Direct Drive Header (TFT) This RSK+ board is fitted with a LCD Direct Drive thru-hole pattern, which allows connection to compatible Renesas LCD application boards. Further details of LCD Direct Drive Header (TFT), refer to §7. 5.12 External Bus The RX65N features an external data bus, which is connected to various devices on the RSK+ board.
RSK+RX65N User Circuitry 5.17 SD Slave Interface (SDSI) This RSK+ board is fitted with a SD Slave Interface (SDSI) thru-hole pattern. The connections for the SDSI signals are listed in Table 5-14 below. SDSI (2x8 thru-hole) Circuit Net Name Circuit Net Name Port Port SDSID2-B...
RSK+RX65N Configuration 6. Configuration Modifying the RSK+ This section lists the option links that are used to modify the way RSK+ operates in order to access different configurations. Configurations are made by modifying link resistors or headers with movable jumpers or by configuration DIP switches A link resistor is a 0Ω...
RSK+RX65N Configuration E1/E2 Lite Debugger Configuration Table 6-2 below details the function of the option links associated with E1/E2 Lite Debugger Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function R249 R110 E1.5 TDO_TXD1 R129 TXD1 R110 R249 U7.3 R109 R116,...
RSK+RX65N Configuration Power Supply Configuration Table 6-4 below details the function of the option links associated with Power Supply Configuration. Reference Explanation Related Ref. VBUS0 Connect 5V Power rail to VBUS0. J17.shorted, J8.Pin2-3 Simple IIC pull-up resistor, Board_5V Connect 5V power rail to Board_5V. R239 5V_PWR, U10.8, U11.3, J19.1, TFT.1, TFT.2...
RSK+RX65N Configuration Analog Power & ADC & DAC Configuration Table 6-7 below details the function of the option links associated with Analog Power & ADC & DAC Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function R447 ADTRG0n ADTRG0n JA1.8 LED1...
RSK+RX65N Configuration BUS & SDRAM Configuration Table 6-8 to Table 6-11 below details the function of the option links associated with BUS & SDRAM Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function R314 PMOD1.10 P55_WAITn WAITn R314 JA3.45 R256 R255...
RSK+RX65N Configuration CAN Configuration Table 6-12 below details the function of the option links associated with CAN Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function PCKO R291, R346 R92, R93 J19.5 U11.4 R199 PCKO_CRX0_MTIOC0D_IRQ3-DS CRX0 R93, R346 R92, R291 JA5.6...
RSK+RX65N Configuration 6.11 General IO & LED Configuration Table 6-19 below details the function of the option links associated with General IO & LED Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function LED0 R306 R162, R192 LED0 LED0_IRQ11_DA0 IRQ11 R162...
RSK+RX65N Configuration 6.12 I2C & EEPROM Configuration Table 6-20 and Table 6-21 below detail the function of the option links associated with I2C & EEPROM Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function SSCL7(PDC-SSCL7) R438 J19.20 R303 SSCL7_RXD7 RXD7 R381...
RSK+RX65N Configuration 6.13 MTU & POE Configuration Table 6-22 and Table 6-23 below details the function of the option links associated with MTU & POE Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function JA6.13 MTIOC3A R283, R324 TFT.26 MTIOC3A_IRQ7_PIXD3 38 P17...
RSK+RX65N Configuration 6.15 PDC Configuration Table 6-25 and Table 6-26 below details the function of the option links associated with PDC Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function JA6.13 MTIOC3A R283, R324 TFT.26 MTIOC3A_IRQ7_PIXD3 38 P17 IRQ7 R324 R77, R283...
RSK+RX65N Configuration 6.22 Serial & USB to Serial Configuration Table 6-33 below details the function of the option links associated with Serial & USB to Serial Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function R249 R110 E1.5 TDO_TXD1 31 P26 TXD1...
RSK+RX65N Configuration 6.23 USB Configuration Table 6-34 below details the function of the option links associated with the USB Configuration. MCU Peripheral Selection Destination Selection Signal name Interface Signal /Function BACKLIGHT R232 TFT.35 BACKLIGHT_USB0OVRCURA USB0OVRCURA R70 R232 U4.2 USB0VBUSEN R119, R275, R332 U4.1 USB0VBUSEN_PIXCLK_MTCLKA PIXCLK...
7. Headers Application Headers This RSK+ board is fitted with application headers, which can be used to connect compatible Renesas application devices or as easy access to MCU pins. Table 7-1 below lists the connections of the application header, JA1.
Page 50
RSK+RX65N 7. Headers Table 7-2 below lists the connections of the application header, JA2. Application Header JA2 Header Name Header Name MCU Pin MCU Pin Circuit Net Name Circuit Net Name RESET EXTAL RESn CON-EXTAL Vss1 NMIn GROUND WDT_OVF SCIaTX TXD2 IRQ0 / WKUP / M1_HSIN0 SCIaRX...
Page 51
RSK+RX65N 7. Headers Table 7-3 below lists the connections of the BUS application header, JA3. Application Header JA3 (Bus) Header Name Header Name MCU Pin MCU Pin Circuit Net Name Circuit Net Name WR / SDWE 56/112 WRn / WEn CS4n CON_SDCSn SDCLK...
Page 52
RSK+RX65N 7. Headers Table 7-4 below lists the connections of the application header, JA5. Application Header JA5 Header Name Header Name MCU Pin MCU Pin Circuit Net Name Circuit Net Name ADC4 ADC5 AN004 AN005 ADC6 ADC7 AN006 AN007 CAN1TX CAN1RX CTX0 CRX0...
Page 53
RSK+RX65N 7. Headers Table 7-5 below lists the connections of the application header, JA6. Application Header JA6 Header Name Header Name MCU Pin MCU Pin Circuit Net Name Circuit Net Name DREQ DACK EDREQ0 EDACK0 TEND STBYn RS232TX RS232RX SCIbRX SCIbTX RXD5 TXD5...
RSK+RX65N 7. Headers Generic Headers Generic headers, used to provide easy connections to various pins from devices fitted to the RSK+. Table 7-6 below lists the connections of the LCD Direct Drive (TFT) Header. LCD Direct Drive Header (TFT) Header Name Header Name MCU Pin MCU Pin...
8. Code Development Overview For all code debugging using Renesas software tools, the RSK+ board must be connected to a PC via an E1/E20/E2 Lite debugger. An E1/E2 Lite debugger is supplied with this RSK+ product. For further information regarding the debugging capabilities of the E1/E20/E2 Lite debuggers, refer to E1/E20 Emulator, E2 Emulator Lite Additional Document for User's Manual (R20UT0399EJ).
Page 59
SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. California Eastern Laboratories, Inc. 4590 Patrick Henry Drive, Santa Clara, California 95054-1817, U.S.A. Tel: +1-408-919-2500, Fax: +1-408-988-0279 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K...
Need help?
Do you have a question about the RX65N Series and is the answer not in the manual?
Questions and answers