Table of Contents
Advertisement
eLectronic toiLet oPeration (cont'd)
1. adding More water to toilet bowl
Pull up the flush handle (4300 model) or push "Add Water" switch (4400 model) until the desired water level
is attained.
2. flushing the toilet
Push the flush handle down (4300 model) or push "Flush" switch (4400 model) for a moment, then release it.
ManuaL override
In the event of a power failure, you can use the "Manual Override Lever" to open the flush ball (for toilet use)
until power is restored. The flush ball will close only when electrical power is restored.
ProPer cLeaninG and Maintenance
Clean your SeaLand toilet regularly for maximum sanitation and operating effi-
ciency. You can clean it just as you would a household toilet. do not use caustic
chemicals, such as drain-opening types, as they will damage the seals.
bowL cLeaninG: For stubborn stains, use SeaLand Toilet Bowl Cleaner (Fig.
A). It's made especially for use with SeaLand toilets. Where water is hard, a
build-up of lime may dull the toilet bowl finish. Restore the shine with this cleaner.
If you cannot find our brand in your area, contact SeaLand Product Customer
Service for your nearest dealer. If it is not available, you can also use most non-
abrasive bathroom and toilet bowl cleaners (Bar Keeper's Friend
Clorox
toilet bowl cleaner, SaniFlush
®
label instructions.
SeaL cLeaninG: After an extended time, mineral deposits from hard water
can build up under the edge of the bowl seal, resulting in a slow leakdown of
water from the bowl. To prevent this mineral build-up, periodically clean under
the bowl seal with SeaLand Toilet Bowl Cleaner (Fig. B).
. Shut off electrical power supply to toilet.
2. Apply cleaner onto a cleaning tool (soft-bristle brush, etc.). Open the flush
ball by pressing on Manual Override Lever. Scrub under entire seal, making
sure to scrub all parts of seal that come into contact with flush ball.
3. Remove cleaning tool. Wait 2-3 minutes.
4. Use water and cleaning tool to rinse cleaner and loosened deposits away.
5. Turn on electrical power to close flush ball. Water will flow into bowl when
power is restored to toilet.
to avoid damaging the teflon
– abrasives (comet
– caustic chemicals (drano
– lubricants and cleaners containing alcohols or
petroleum distillates
(Pam
cooking spray, Pine-Sol
®
lubricant, etc.).
WINteRIzING
At the end of each traveling season, the SeaLand toilet system must be winterized for storage. The following
procedure should be used:
. Pump out waste holding tank.
2. Thoroughly flush toilet system with fresh water.
3. Drain freshwater tank.
4. Add freshwater antifreeze to freshwater tank.
5. Flush freshwater antifreeze and water mixture through toilet and into the waste holding tank. Each installation
is different so amounts may vary. User discretion is required to assure adequate protection.
6. Turn off electrical power.
caution: The use of freshwater antifreeze that contains alcohol will result in damage to your sanitation
system. Only use propylene glycol freshwater antifreeze that does not contain alcohol.
toilet bowl cleaner, etc.). Please follow
®
-coated seal, dO NOt uSe:
®
, Soft Scrub
cleansers etc.)
®
®
clog remover, etc.)
®
cleaner, wd-40
®
spray cleaner,
®
® Bar Keepers Friend is a registered trademark of SerVaas
Laboratories Inc.
® Clorox, Pine-Sol and Soft Scrub are registered trademarks of
The Clorox Co.
® Comet is a registered trademark of Prestige Brands International.
® Drano is a registered trademark of S.C. Johnson & Son Inc.
® Pam is a registered trademark of ConAgra Foods.
®
® Sani-Flush is a registered trademark of Reckitt Benckiser Inc.
® Teflon is a registered trademark of DuPont Co.
® WD-40 is a registered trademark of WD-40 Company.
9
fig. a
fig. b
Advertisement
Table of Contents
