Operation - Kaiser K113-4BJCI Assembly Instructions Manual

Burning-off
Before first use, remove any production residue and clean the appliance:
1. Operate the appliance at high temperature with the cover opened for about 10 - 15 minutes to burn off production residues (→ IGNITING THE BURNER(S) /
SIDE BURNER(S)).
2. Turn the appliance off; allow it to cool down before cleaning all the parts (→ CLEANING AND CARE).

OPERATION

WARNING! Danger of burns!
This appliance generates heat and escaping steam during use! Take proper precautions to prevent risk of burns, fires, or other damages to people
and property! Wear protective oven mittens or gloves. Use proper tools like barbecue tong and prongs to turn over grillables!
COOKING TIPS
1. Brush the grill grates with cooking or vegetable oil prior to using the appliance. Use a brush with a long handle. Juices from the food drip onto the heater
during cooking and vaporise. The steam arising from this process contributes to the taste of the food.
2. Adjust the control knob(s) between "HI" to "LO" position in order to achieve your desired cooking results. The built-in thermometer on the cover could be used
for reference (not calibrated).
3. Keep the cover(s) closed in order to achieve a more consistent result and to cook larger pieces of meat or whole chickens.
4. Avoid opening the cover(s) too often as accumulated heat escapes each time, increasing the grilling duration as a result.
IGNITING THE BURNER(S) / SIDE
The burner(s) can be ignited with the spark ignition which combine with the gas tap(s) or manually with a match.
1. Wait 5 minutes after all connections are made and make sure no gas is leaking (→ Testing for gas leaks).
2. Open the cover(s) of the appliance. Turn all control knobs to the off positions OFF.
3. Open the valve of the gas cylinder or the pressure regulator.
4. Keep your face and body as far away from the appliance as possible while igniting.
5. Follow the procedure for each method as described below.
WARNING! Risk of explosion!
Always ignite the burner(s) within 5 seconds after turning the control knob to a position in between HI and LO. Gas can collect inside the appliance
causing an explosion on ignition.
WARNING! Risk of explosion!
Turn all the control knobs to the off positions OFF, if any burner does not ignite within 5 seconds. Wait for 5 minutes to let the gas dissipate and try
again.
WARNING!
If any burner still does not ignite after a few tries, it could indicate a problem with the gas supply. Turn the gas supply off on the appliance as well as
on the gas cylinder or the pressure regulator. Do not use the appliance until the cause of the problem has been found (→ TROUBLESHOOTING).
Igniting the main burner with the spark ignition which with pilot
1. Wait 5 minutes after all connections are made and make sure no gas is leaking (→ Testing for gas leaks).
2. Push the control knob of the selected burner in (A) and hold in this position for 3-5 seconds to allow gas flow and then turn anticlockwise to "HI" position (B).
It can spark to the burner lighting tube (C). You will hear a „snap" from the igniter and you will also see a 3" – 5" length of orange flame coming from pilot at
left side of the burner (D). Continue to hold the burner control knob in for two seconds after the "snap", this will allow gas to flow completely down the burner
tube (E) and insure ignition.
3. To adjust the heat, set the control knob between HI and LO position.
4. Ignite the other burner(s) using their respective control knob(s) after the first burner has fired up.
B
A
HI
LO
MAIN BURNER
Igniting the side burner with the spark ignition which without pilot
1. Wait 5 minutes after all connections are made and make sure no gas is leaking (→ Testing for gas leaks).
2. Push and turn the control knob anticlockwise from off position to "HI", and continuous 4 to 5 times to ignite the burner.
3. To adjust the heat, set the control knob between HI and LO position.
Igniting the main burner(s) with a match
1. Insert a long stick match into the match holder.
2. Light the match and insert it through the grill grates close to the burner you want to ignite. Push and turn the control knob of the selected burner to the
HI position.
3. To adjust the heat, set the control knob between HI and LO position.
E
D
C
11
GB