Page 2
Dear Customer, Thank you for choosing an AERMEC product. This product is the result of many years of experience and in-depth engineering research, and it is built using top quality materials and advanced technologies. We constantly monitor the quality level, and as a result AERMEC products are synonymous with Safety, Quality, and Reliability.
Indice General warnings for the installer ......................5 Selection and place of installation ......................6 Positioning ..............................6 Minimum technical clearances ......................... 6 Operation of the nlc unit .......................... 6 Max static useful pressure of the fans ..................... 7 Main hydraulic circuits ..........................9 Electrical wirings ............................
Aermec shall not be held responsible for any damage whatsoever resulting from the non-compliance with these instructions. Before starting any kind of work, it is necessary TO READ CAREFULLY THE INSTRUCTIONS, AND TO PERFORM THE SAFETY CHECKS TO REDUCE ALL HAZARDS TO A MINIMUM.
SELECTION AND PLACE OF INSTALLATION Position the unit in the place indicated by the customer, placing, between the base and the support, a rubber mattress (minimum 10 mm. thick) or Before installing the unit, decide with the customer where it will be placed, anti-vibration dampers (ACCESSORIES).
MAX STATIC USEFUL PRESSURE OF THE FANS THESE TABLES LOOK INCORRECT FOR AIRFLOW AND STATIC PRESSURE. PLEASE HAVE THIS CHANGED FOR NORTH AMERICA Default ESP [Pa] Total air Max ESP NLC-HA flow rate [Pa] Parameter fans max Volts [V] 0280 23000 0300 26500...
50% of the nominal capacity Alkalinity (HCO3) 70 - 300 ppm Chlorine ions (Cl-) < 50 ppm Aermec will not be responsible for any Sulphate ions (SO4) < 50 ppm damage to the heat exchanger if there is no Sulphide ion (S)
Page 9
50% of the nominal capacity Alkalinity (HCO3) 70 - 300 ppm Chlorine ions (Cl-) < 50 ppm Aermec will not be responsible for any Sulphate ions (SO4) < 50 ppm damage to the heat exchanger if there is no Sulphide ion (S)
Page 10
50% of the nominal capacity Alkalinity (HCO3) 70 - 300 ppm Chlorine ions (Cl-) < 50 ppm Aermec will not be responsible for any Sulphate ions (SO4) < 50 ppm damage to the heat exchanger if there is no Sulphide ion (S)
ELECTRICAL WIRINGS Check that all power cables are correctly secured to the terminals when switched on for the first time and after 30 days of use. Afterwards, check The NLC units are fully wired in the factory and only require connection them every six months.
ELECTRICAL DATA TABLE Power Supply: EARTH (PE) PHASE 0280 0300 0330 0350 0550 0600 0650 0675 0750* 0750** 0800 0900 1000 1100 1250 Electrical data 208V-3-60 Hz Whitout pump °° A °° A °° A Fuse recommended °° A Electrical data 230V-3-60 Hz Whitout pump °°...
Page 13
User Interface (PGD1) The unit control panel allow the quick setti ng and INTERFACE CONTROL KEYS display of the unit’s operati ng parameters. The board memorises all the default setti ngs and any modifi ca- Control Keys Control Keys ti ons. By installing the remote control panel PGD1 it is possible to remotely replicate all the functi ons and the setti ngs available on the unit.
Page 14
Start-up procedure any ti me through the appropriate screen contained Aft er having powered up the unit the control board will select the system language. These screens are detailed in the Installer menu. carry out preliminary operati ons before being ready in the table below.
Page 15
Menu structure and navigati on Both the functi ons to control the unit and the operati ng informati on The operati ng menus are arranged as in the following drawing: are displayed on the unit mounted control panel. All the functi ons and informati on are arranged in screens which in turn are grouped into menus.
Page 16
User operating procedures To check or modify the operati ng parameters of the unit it is necessary to use the interface of the control panel on the unit. The basic operati ons that the user must be capable of, for the correct use of the unit, are: (1) Moving from one menu to the next.
LOADING THE SYSTEM Before starting the loading, set the unit's master switch to OFF Check that the system discharge tap is closed Open all the drain valves of the system and of the related terminals Open the cut-off devices of the system. Start the filling by slowly opening the water system filling tap on the outside of the appliance.
Page 18
Aermec Technical Service for close the flow switch contact. the unit of this series, at the request of Aermec Check the water flow rate, measuring the CHECK: customers or legitimate owners and in ITALY difference of pressure between the evaporator only.
ROUTINE MAINTENANCE DISPOSAL Any cleaning operations are forbidden until the The disposal of the unit should be carried out unit has been disconnected from the electrical according to the rules in force in the various power supply mains countries. Make sure there is no voltage before operating. Periodic maintenance is essential to maintain the WARNING unit in perfect working order under the functional...
TROUBLESHOOTING IRREGULARITY CAUSE SOLUTION • Check for voltage • No electrical voltage • Check the safety systems upstream of the appliance • Master switch on OFF • Remote switch on OFF (if present) • Control panel on OFF • Set to ON •...
LIFTING POINTS AND ANTIVIBRANT POSITION PLEASE ADD TABLES SHOWING WEIGHT DISTRIBUTION FOR EACH 280-350 HA-HE P1-P8 280-350 HA 280-350 HA-HE 00 POINT LIKE WE HAVE FOR OTHER UNITS 280-350 HA-HE 00 PALLET 280-350 HA-HE P1-P8 280-350 HA-HE 01-08 280-350 HA-HE 00 PALLET PALLET PALLET...
AERMEC SAS - AGENCE SILLON ALPIN - 7, Chemin des Roquevillard - 73160 Cognin - Tél. +33 04 85013570 - Fax +33 04 74090988 - jerome.dubouchet@aermec.fr AERMEC SAS - Ile de France - 80 Avenue du Général De Gaulle - 91170 Viry Chatillon - Tél. +33 1 60478348 - Fax +33 1 69436368 - gianni.delfabbro@aermec.fr DIMENA SARL - 88 Rue Du Moulineau - 33320 Eysines - Tél.
Page 47
AIRMEC ROMANIA S.RL. - 29 lezeru Street, Sector 1 - Bucharest - Ph. +40 21 550866589 - Fax +40 21 3260973 - airmec@adslexpress.ro RUSSIA AERMEC Spa - Rep. Office Business Center Capital Plaza, 4 Lesnoy Pereulok - office 455 - 125047 Moscow - Ph. +7 495 6638044 - m.l@aermec.com SERBIA & MONTENEGRO AKTING DOO - Jurija Gagarina, 153/32 -11070 Novi Beograd - Ph.
Page 48
37040 Bevilacqua (VR) - Italia Tel. + 39 0442 633111 Fax +39 0442 93577 marketing@aermec.com carta riciclata www.aermec.com recycled paper papier recyclé recycled Papier Aermec si riserva la facoltà di apportare in qualsiasi momento tutte le modifiche ritenute necessarie per il miglioramento del prodotto.