Operation - Makita DMR300 Instruction Manual

Charging with USB power supply port
CAUTION:
Do not connect power source to
USB port. Otherwise there is risk of fire. The USB
port is only intended for charging lower voltage
device. Always place the cover onto the USB port
when not charging the lower voltage device.
CAUTION:
Do not insert a nail, wire, etc. into
USB power supply port. Otherwise a circuit short
may cause smoke and fire.
NOTICE:
Before connecting USB device to the
charger, always backup your data of USB device.
Otherwise your data may lose by any possibility.
NOTICE:
When not using or after charging, remove
the USB cable and close the cover.
NOTICE:
Do not connect this USB socket with your
PC USB port, as it is highly possible that it may cause
breakdown of the units.
NOTE: The charger may not supply power to some
USB devices.
There are USB power supply ports at the front and back
side of the radio. You can charge USB device through
the USB power supply port.
► Fig.10: 1. USB power supply port
1. Connect the USB device, such as a MP3 or CD
player, to the USB power supply port using a USB cable
available in the market.
2. Press the Power button
NOTE: No matter if the radio is AC powered or battery
powered, you can charge a USB device when the
radio is switched on and in FM radio mode, Bluetooth
mode, or AUX mode which is appeared when an
external audio source is connected.
NOTE: The maximum volume of the output power speaker
will decrease when your USB device is being charged.
NOTE: The USB socket can provide max 2.4 A 5 V (2
port total) of electrical current.
Charging the battery cartridge
To charge the battery cartridge with this radio, insert the adap-
tor plug into the DC IN socket and then plug it to the mains.
After that, insert the battery cartridge to the slot.
► Fig.11: 1. LXT battery cartridge 2. CXT battery car-
tridge 3. Indicator for battery status/capacity
The indicator for battery status/capacity blinks when the
battery cartridge is being charged. The charging status
is as follows:
Indicator for battery status/
capacity
(blinking)
(blinking)
(not blinking)
to switch on the radio.
Charging status
Charging (less than 80%)
Charging (80% or more has
been charged)
Charged (100%)
NOTICE:
You cannot charge LXT and CXT bat-
tery cartridges at the same time.
NOTE: It will take several seconds until the indicator
for battery status/capacity appears after the AC power
adaptor is plugged into the mains.
NOTE: If the AC power adaptor is disconnected from
the radio during battery charging, the radio turns off
for a few seconds and then automatically turns on
with the battery power supply.
Hook for the AC power adaptor
The hook on the back of the radio is useful for carrying
the AC power adaptor. When carrying, bundle the cords
and tie them with AC power adaptor using the band.
► Fig.12: 1. Hook 2. AC power adaptor 3. Band
NOTICE:
Do not store AC power adaptor in the
battery compartment. The cord may be pinched and
damaged when closing the battery cover.
NOTICE:
Always hold the handle when carrying
the radio.
NOTICE:
Be careful not to drop the AC power
adaptor hooked on the back of the radio.
Bottle cap opener
The bottle cap opener is provided on the back of the radio.
► Fig.13: 1. Bottle cap opener
NOTICE:
Hold the radio firmly when using the
bottle cap opener. Failure to do so may cause the
radio tipped over and result in damage or malfunction.
NOTICE:
Be careful not to spill the beverage
onto the radio when opening the cap.

OPERATION

Switching on/off the radio
Press the Power button
Press the Power button
radio.
Adjusting the volume level
Turn the Tuning control knob
the volume. Turn the Tuning control knob
clockwise to decrease the volume.
NOTE: The volume adjustment is not available during
tuning and some settings.
Scan tuning AM/FM or DAB
1.
Press the Power button
radio.
2. Press the Source button
DAB radio mode.
12 ENGLISH
to switch on the radio.
again to switch off the
clockwise to increase
counter-
to switch on your
to select AM/FM or