Operation - Makita XRM10 Instruction Manual

OPERATION

Switching on/off the radio
Press the Power button
Press the Power button
radio.
Adjusting the volume level
Turn the Tuning control knob
the volume. Turn the Tuning control knob
clockwise to decrease the volume.
NOTE: The volume adjustment is not available during
tuning and some settings.
Scan tuning AM/FM
1. Press the Power button
radio.
2. Press the Source button
radio mode.
3. Press and hold the Tuning control knob
out an auto-tune.
Your radio will scan up the AM or FM band from the cur-
rently displayed frequency and will stop scanning auto-
matically when it finds a station of sufficient strength.
NOTE: The stations to be found by scan tuning vary
depending on the receiving sensitivity at the location
where the scan tuning is performed. If you don't have
desired station, change the location and perform the
procedure above.
NOTE: When the end of the waveband is reached
your radio will recommence tuning from the opposite
end of the waveband.
Manual tuning – FM/AM
1. Press the Power button
2. Press the Source button
mode.
3.
Press the Tuning control knob
4.
Rotate the Tuning control knob
station.
5. Press the Tuning control knob
tuning.
NOTE: Manual tuning is available while "MANUAL
TUNING" is displayed on the display. If "MANUAL
TUNING" is not displayed, start the manual tuning
from the beginning.
NOTE: The stations to be found by manual tuning
vary depending on the receiving sensitivity at the
location where the manual tuning is performed. If you
don't have desired station, change the location and
perform the procedure above.
NOTE: When the end of the waveband is reached
your radio will recommence tuning from the opposite
end of the waveband.
to switch on the radio.
again to switch off the
clockwise to increase
counter-
to switch on your
to select AM or FM
to carry
to switch on your radio.
to select FM/AM radio
.
to tune to a
to set the
Presetting stations in FM/AM
There are 5 preset stations each for FM/AM radio. They
are used in the same way for each waveband.
1. Press the Power button
radio.
2.
Press the Source button
waveband. Tune to the required radio station.
3. Press and hold the required Preset button (1 to
5) until the display shows "PRESET X
STORED" (X indicates the number of the Preset button
that you pressed). The station will be stored using the
preset number (P1-P5). Repeat this procedure for the
remaining presets as you wish.
NOTE: Preset stations which have already been
stored may be overwritten by following the above
procedure.
Recalling a preset station in AM/FM
1. Press the Power button
radio.
2. Press the Source button
radio mode.
3.
Press the desired Preset button
you stored in the preset memory.
Display modes – FM
Your radio has a range of display options for FM radio
mode.
Station name
Program type
Radio text
Time/Date
Setting the clock
Setting the time and date format
NOTE: The selected time and date format is also
used when setting the alarms.
1.
Press and hold the Menu/Info button
the menu setting.
2. Rotate the Tuning control knob
appears on the display and press the Tuning control
knob to enter the setting.
3. Rotate the Tuning control knob
12/24 HOUR> appears on the display and press the
control knob to enter the setting.
13 ENGLISH
to switch on your
to select the desired
to switch on your
to select AM or FM
that
Displays the name of the sta-
tion being listened to, together
with the band and frequency.
Displays the type of station
being listened to such as Pop,
Classic, News, etc, together
with the band and frequency.
Displays radio text message
such as new items etc,
together with the band and
frequency.
Displays the time and date
according to the date setting
of your radio.
to enter
INFO
MENU
until <TIME>
until <SET