Siemens SIMATIC MV500 Operating Instructions Manual page 231

Error code Error message
(%c) (%s)
4710 Verification failed in step n: Data Matrix ECC200
required
4711 Verification failed in step n: Aperture too small
4712 Verification failed in step n: Aperture too large
4713 Verification failed in step n: Not enough space
around the Data Matrix
4714 Verification failed in step n: RDA could not find the
horizontal timing pattern
4715 Verification failed in step n: RDA could not find the
vertical timing pattern
4716 Verification failed in step n: RDA found an incor-
rect number of rows and columns
4717 Verification failed in step n: RDA could not locate
the finder pattern
4719 Verification failed in step n: RDA error correction
failed
4720 Verification failed in step n: Number of Data Ma-
trix rows/columns is too high
4721 Verification failed in step n: Cell size is smaller
than the specified Min.X Dim.
4722 Verification failed in step n: Cell size is larger than
the specified Max.X Dim.
5000 Not enough resources to process step n
5001 No objects found in step n
5001 No objects found in step n
5002 Too few objects found in step n
5003 Too few objects found in step n: Required feature
is missing
SIMATIC MV500
Operating Instructions, 03/2021, C79000-G8976-C494-05
10.1 Error and diagnostics messages
Description
Verification requires a data matrix code according to
ECC200 specification (only for verification according to
ISO/IEC 15415 or ISO/IEC 29158).
The cell size of the data matrix code in step #n is too
large for the configured aperture (only for verification
according to ISO/IEC 15415).
The cell size of the data matrix code in step #n is too
small for the configured aperture (only for verification
according to ISO/IEC 15415).
The quiet zone around the data matrix contained in
the image is too small. For verification, a quiet zone of
at least the size of two cells is required (only for verifi-
cation according to ISO/IEC 15415 or 29158).
The reference decoding according to
ISO/IEC 16022:2006 signals an error when searching
for the horizontal timing pattern (only for verification
according to ISO/IEC 15415 or ISO/IEC 29158).
The reference decoding according to
ISO/IEC 16022:2006 signals an error when searching
for the vertical timing pattern (only for verification
according to ISO/IEC 15415 or ISO/IEC 29158).
The reference decoding according to
ISO/IEC 16022:2006 signals an error when determin-
ing the number of rows or columns (only for verifica-
tion according to ISO/IEC 15415 or ISO/IEC 29158).
The reference decoding according to
ISO/IEC 16022:2006 signals an error when searching
for the finder pattern (only for verification according
to ISO/IEC 15415 or ISO/IEC 29158).
The reference decoding according to
ISO/IEC 16022:2006 signals an error when determin-
ing the error correction (only for verification according
to ISO/IEC 15415 or ISO/IEC 29158).
The maximum supported code size for verification
according to ISO/IEC 15415 or ISO/IEC 29158 is
104x104 cells.
During verification, a cell size was measured that is
less than the minimum X-dimension setting (only for
verification according to ISO/IEC 29158).
During verification, a cell size was measured that is
greater than the maximum X-dimension setting (only
for verification according to ISO/IEC 29158).
Step #n could not be executed due to a lack of re-
sources (memory).
Locator: No objects were found in step #n.
Locator: No objects were found in step #n.
Locator: The number of objects found in step #n is
lower than the set minimum.
Locator: The number of objects found in step #n is
lower than the set minimum. At least one object was
rejected because of a missing required feature.
Service and maintenance
231