Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® Elektrowerkzeugs entsprechen. Falsch bemessene 4. Allgemeine Sicherheitshinweise Einsatzwerkzeuge können nicht ausreichend abgeschirmt oder kontrolliert werden. WARNUNG – Lesen Sie alle • Einsatzwerkzeuge mit Gewindeeinsatz müssen Sicherheitshinweise und Anweisungen. genau auf die Schleifspindel des Elektrowerkzeugs Versäumnisse bei der Einhaltung der Sicherheitshinweise passen.
Page 8
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® Leitung kann auch metallene Geräteteile unter geeignete Vorsichtsmaßnahmen, wie nachfolgend Spannung setzen und zu einem elektrischen Schlag beschrieben, verhindert werden. führen. • Halten Sie das Elektrowerkzeug gut fest und bringen Sie Ihren Körper und Ihre Arme in eine •...
Page 9
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® Überlasten Sie die Drähte nicht durch zu hohen • Immer mit angebrachter Schutzhaube arbeiten. Anpressdruck. Wegfliegende Drahtstücke können • Maschine immer mit beiden Händen an den sehr leicht durch dünne Kleidung und/oder die Haut vorgesehenen Handgriffen führen.
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® Transport von Li-Ion-Akkupacks: • den Arbeitsplatz gut lüften und durch saugen sauber halten. Fegen oder blasen wirbelt Staub auf. Der Versand von Li-Ion Akkupacks unterliegt dem • Saugen oder waschen Sie Schutzkleidung. Nicht Gefahrgutrecht (UN 3480 und UN 3481).
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 8. Zubehör 9. Inbetriebnahme Speziell für Netzmaschinen: Verwenden Sie nur original Eisenblätter Akkupacks und Eisenblätter Zubehör. Vergleichen Sie vor Inbetriebnahme, ob die auf Verwenden Sie nur Zubehör, das die in dieser dem Typenschild angegebene Netzspannung und Betriebsanleitung angegebenen Anforderungen und Netzfrequenz mit den Daten Ihres Stromnetzes...
Page 13
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® Feinstaubschutz-Kappe: Akkupack: Anbringen: Siehe Seite 2, Abbildung A4/A5. Vor der Benutzung den Akkupack (B1-3) aufladen. Feinstaubschutz-Kappe wie gezeigt anbringen. Laden Sie den Akkupack bei Leistungsabfall wieder auf. Die optimale Aufbewahrungstemperatur liegt zwischen Abnehmen: 10°C und 30°C.
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 10. Ein- und Ausschalten 11. Anbringen der Werkzeuge, Arbeitshinweise Maschine immer mit beiden Händen führen. 11.1 Einsatzwerkzeuge anbringen Netzmaschinen: Erst einschalten, dann das Einsatzwerkzeug an Spindelarretierknopf (A2-2) nur bei stillstehender das Werkstück bringen.
Originalbetriebsanleitung POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 12. Störungsbeseitigung 14. Reparatur 12.1 Netzmaschinen: Reparaturen an Elektrowerkzeugen dürfen nur durch eine Elektrofachkraft ausgeführt werden! Die Elektronik-Signal-Anzeige (A1-4) leuchtet und die Lastdrehzahl nimmt ab. Die Belastung Wenn die Anschlussleitung beschädigt wird, muss sie der Maschine ist zu hoch! Maschine im Leerlauf durch eine besondere Anschlussleitung ersetzt werden.
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® English 2. Specified conditions of use The burnishing machine is suited for Table of contents • burnishing, deadening, structuring and brushing, • polishing and smoothing, 1. EC-Declaration of conformity ....16 •...
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® by flanges, the arbour hole of the accessory must 4. General safety information fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively WARNING –...
Page 18
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® • Regularly clean the power tool’s air vents. The Safety warnings specific for sanding operations: motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may •...
Page 19
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® • The workpiece must lay flat and be secured against • Do not open battery packs! slipping, e.g. using clamps. Large workpieces must be • Do not touch or short circuit battery pack contacts! sufficiently supported.
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® • Use a suitable extraction unit. 6. Product features Reduce dust exposure with the following measures: 6.1. Power tool POLY-PTX 802 HT – see ® • Do not direct the escaping particles and the exhaust page 2-3 (Figure A1and A2): air stream at yourself or nearby persons or on dust A1-1...
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 7. Technical data *POLY-PTX 802 HT: High-energy, high-frequency Subject to change in accordance with technical progress. ® interferences can cause speed fluctuations. The Measured values determined in conformity with fluctuations disappear, however, as soon as the EN 60745.
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 8. Accessories 9. Initial operation For mains powered machines only: Only use original Eisenblätter battery packs and Eisenblätter accessories. Before commissioning, check that the rated mains Use only accessories that fulfil the requirements and voltage and mains frequency, as stated on the specifications listed in these operating instructions.
Page 23
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® Particulate matter protection cap: Battery pack: Attachment: See page 2, figure A4/A5. Charge the battery pack (B1-3) before use. Fit the particulate matter protection cap as shown. Recharge the battery pack if performance diminishes. The ideal storage temperature is between 10°C and To remove: 30°C.
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 10. Switching on and off 11. Attaching the tools, working notes 11.1 Attaching tools mains powered machines: Always guide the machine with both hands. Press in the spindle locking button (A2-2) only Switch on first, then guide the accessory towards when the spindle is stationary! the workpiece.
Original instructions POLY-PTX 802 HT / POLY-PTX AKKU HT ® ® 12. Troubleshooting 14. Repairs 12.1 Mains powered machines: Repairs to power tools must only be carried out by qualified electricians! The electronic signal indicator (A1-4) lights up and the load speed decreases. There is too If the connection lead is damaged, it must be replaced much load on the machine! Run the machine in by a special connection lead.