Advertisement
Quick Links
Advertisement
Related Manuals for eisenblatter Gladius 1800
Summary of Contents for eisenblatter Gladius 1800
- Page 1 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Manual...
- Page 2 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Foreword: You have made a good decision buying our GLADIUS 1800. In just one machine you will find a belt-grinder, fl ® at-grinder, belt-polishing-machine, deburring-machine and wood-treatment-machine! GLADIUS 1800 ®...
-
Page 3: Maintenance
G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Maintenance: Changing the carbon brushes: Remove the plug from the power socket (so there is no electric current anymore!), unscrew and lift/remove the service cover. Branch off the wires, remove the carbon brushes and clean the carbon brush holder with compressed air. - Page 4 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Details / Features: Protective cover with suction flange Innovative stop button enables Very compact, well-balanced Long, sword-shaped, belt-driven for optional connection to all lightning-fast replacement of belt design with bow handle for tool for machining previously standard industrial vacuum...
- Page 5 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Application / Operation: Putting on the belt 1. Place the machine upright. Press and hold the locking pin (1) while applying pressure on the bottom end with a downward motion, until the locking pin locks.
- Page 6 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD 3. Again raise the machine upright and apply light pressure on its tip… until the locking pin releases automatically. www.111abrasives.com.au Phone (07) 5546 6026 Fax: (07) 5546 6381...
- Page 7 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Adjusting the belt (rear) To adjust the grinding / polishing belt, here are the following tools that are included when the machine is shipped: 1 x Hexagon socket screwdriver (D) 1 x Hexagon socket key SW 5 (E) 1 x Hook wrench (C)
- Page 8 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Adjusting the belt (front) 1. Loosen screw 2 slightly (“open”) 2. Turn screw 1 until you reach your desired position. 3. Tighten screw 2 again. If there is still adjustment necessary, please repeat steps 1 to 3.
- Page 9 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD An example of a grinding / polishing belt sitting incorrectly on the machine: Re-adjustment is necessary. An example of a grinding / polishing belt that is perfectly positioned onto the machine.
- Page 10 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Grinding setups (flat and curved) With the aid of screw A and B (see picture) GLADIUS 1800 can be converted and used ® for either flat or curved grinding. Curved grinding (for on the spot grinding applications)
- Page 11 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD Replacing the driving rubber ring (when worn out) 1. Press the button (1) on the gear box and simultaneously loosen the driving roll with the special wrench (C). Now unscrew the driving roll.
- Page 12 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD 5. Re-assemble the driving roll by screwing the guide discs back on. 6. Screw in the re-assembled driving roll while simultaneously holding the button. Replacing the rubber o-rings on the front guide roll (when worn out) 1.
- Page 13 G L A D I U S 1 8 0 0 ® THE MULTIFUNCTIONAL GRINDING SWORD 3. Remove each o-ring with a needle (picture). Mount new o-rings: Small rings on the out-side (on the left and right) and the big ring in the centre.
- Page 14 Gerd Eisenblätter GmbH Jeschkenstr. 10 DE-82538 Geretsried ® G L A D I U S 1 8 0 0 CE 94 Anlage zur POLY-PTX ® - Bedienungsanleitung THE MULTIFUNCTIONAL GRINDING SWORD CE 94 Declaration of conformity for GLADIUS 1800 ® ENGLISH NEDERLANDS EC DECLARATION OF CONFORMITY...