eisenblatter POLY-PTX 802 HT Original Instructions Manual page 18

EN
Original instructions POLY-PTX
• Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
• Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
• Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
5.2 Kickback and related warnings:
Kickback is a sudden reaction to a pinched or snagged
sanding wheel, backing pad, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory's rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out.
The abrasive wheel may either jump toward or away
from the operator, depending on direction of the disc's
movement at the point of pinching. Abrasive wheels may
also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided if suitable precautionary measures are taken as
described below.
• Maintain a firm grip on the power tool and
position your body and arm to allow you to resist
kickback forces. Always use auxiliary handle, if
provided, for maximum control over kickback or
torque reaction during start-up. The operator can
control torque reactions or kickback forces, if proper
precautions are taken.
• Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
• Do not position your body in the area where the
power tool will move if kickback occurs. Kickback
will propel the tool in direction opposite to the
grinding wheel's movement at the point of snagging.
• Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause
loss of control or kickback.
• Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
18
802 HT / POLY-PTX AKKU HT
® ®
5.3
• Do not use excessively oversized sanding disc
5.4
• Do not allow any loose portion of the polishing
5.5
• Be aware that wire bristles are thrown by the
• If the use of a guard is recommended for wire
5.6
• Use elastic cushioning layers if they have been
• Observe the specifications of the tool or accessory
• Accessories must be stored and handled with care in
• Ensure that accessories are installed in accordance
• The tool continues running after the machine has
• When sanding and working with the lambskin
• Do not use separate reducing bushings or adapters to
Safety warnings specific for sanding
operations:
paper. Follow manufacturers recommendations
when selecting sanding paper. Larger sanding
paper extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing of
the disc or kickback.
Safety warnings specific for polishing
operations:
bonnet or its attachment strings to spin freely.
Tuck away or shorten the loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
Safety warnings specific for wire brushing
operations:
brush even during ordinary operation. Do not
overstress the wires by applying excessive load to
the brush. The wire bristles can easily penetrate light
clothing and/or skin.
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel or
brush may expand in diameter due to work load and
centrifugal forces.
Additional safety instructions:
WARNING – Always wear protective goggles.
supplied with the grinding media and if required.
manufacturer!
accordance with the manufacturer's instructions.
with the manufacturer's instructions.
been switched off.
polishing disc with cord drive always work with the
safety guard installed.
adapt tools with a large hole.
www.eisenblaetter.de