Savant SEM-2015 Quick Reference Manual

Savant® Stand Alone Energy Monitor (SEM-2015)
Quick Reference Guide
Box Contents
(1) Stand Alone Energy Monitor
(1) SmartEnergy Voltage Sensor (SEM-VT01-00)
(1) Install Kit (075-0227-00)
(1) Universal Din Rail Mounting Clip (015-0255-00)
(1) Power Supply (025-0192-00)
(1) 6-Pin Screw Down Connector (028-0664-00)
(15) 2-Pin Screw Down Connector (028-0884-00)
(4) #6x1/4 PH Flat Screws (039-0143-00)
(1) Product Regulatory Insert (009-1808-00)
Accessories (sold separately)
– SEM-VT01 - SmartEnergy Voltage Sensor
– Split Core Current Transformers (Clamp-on) with 8ft leads.
– SEM-020A5 20 Amps
– SEM-050A5 50 Amps
– SEM-150A1 150 Amps
– SEM-150A5 150 Amps
–
SEM-250A1 250 Amps
– SEM-400A1 400 Amps
–
SEM-600A1 600 Amps
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weight
Height 9.5 in (24.13 cm)
Width 9.7 in (24.64 cm)
Depth 3.3 in (8.38 cm)
Weight
Shipping: 2.65 lb (1.2 kg)
Power
Input Power 5V DC
Nominal Power
3W (10W max)
Regulatory
FCC Part 15B
Safety and
Emissions
RoHS Compliant
Minimum Support Requirements
Software
da Vinci 9.1
Release
Important Information
–
All wiring in the United States must be installed in accordance with
the latest adopted edition of the National Electrical Code (ANSI/
NFPA 70, NEC).
– All wiring in Canada must be installed in accordance with the latest
adopted edition of the Canadian Electrical Code (CSA C222.2 CEC,
Part 1) and any provincial or local requirements.
– Savant's largest Current Transformer supports wire up to 500 MCM
(this with jacket is just under 1 inch).
TIP! MCM refers to circular mils and is often used for wire larger
than the AWG measurement accommodates.
– Maximum length for leads on each current transformer should not
exceed 8 feet. Longer lengths will cause inaccurate readings.
– If required, the leads on the current transformers can be shortened.
Stand Alone Energy Monitor | 009-1836-01 | 190703
Copyright 2019 Savant Systems, LLC
5 Pack
5 Pack
1 Pack
5 Pack
1 Pack
1 Pack
1 Pack
CE Mark C-Tick
Left Side Panel
5 VDC
Ethernet
Status
Reset
(Ground)
Right Side Panel
A B C
VT Connections
CT Connections
Current/Voltage Transformer Input Polarity
Current Transformer Input
POS (+) - White or red wire from Current Transformer
GND (-) - Black wire from Current Transformer
POS(+) GND (-)
Voltage Transformer Input
POS (+) - Connect to the positive (+) output on
Voltage Sensor. See diagram in the Install Voltage
Sensors section.
GND (-) - Connect to the GND output of a Voltage
Sensor (SEM-2015). See diagram in Install Voltage
POS(+) GND (-)
Sensors.
1 of 2
Power Input - Connect the supplied power
adapter between the 5V DC port and a surge
protected (120-240V AC, 50/60 Hz) outlet.
8-Pin RJ 45 port. 10/100/1000 BaseT auto-
negotiating port with link activity LEDs
Blinking Red - Embedded firmware is running
but has not received an IP Address.
Solid Green - Connected to the local network
and communicating with the Savant System
Host.
Press and release to perform a hard reset. Status
LED will illuminate while button is pressed.
Device Reset:
1. Disconnect power.
2. Reconnect power wile holding the reset
button for 20 seconds.
Device will reboot clearing its configuration
and resetting its password.
Chassis Ground (optional)
1 2 3 4 5
9 10 11 12 13
Voltage Transformer - (3) Voltage sensor input
ports. Input port for the SEM-VT01 voltage
sensor.
Current Transformer - (15) Input ports for each
Current Transformer installed in the system.
45 Perseverance Way, Hyannis, MA 02601
Savant.com
6 7 8
N/A
14 15
| 508.683.2500