Advertisement
4-3 Function Descriptions
4-3-2 Water Level
1. In all the cases of prior to the first press of START/HOLD
key, during operating or hold state, they follow the below
sequences.
MEDIUM → HIGH → MAXIMUM →
EXTRA LOW → LOW
2. When Super Clean is selected, only MAXIMUM & HIGH &
MEDIUM water level is possible.
3. If you change the course to WOOL, in case previous water
level is low or medium, the water level is automatically
selected High level and in case previous water level is
over Low, the water level is not changed.
4. While water is supplying, if the water level is changed, the
remaining time is changed.
4-3-3 Course
1. If this key is pressed before the first press of
START/HOLD key or during HOLD state, the selection
order is as follow.
Even if manual washing is selected already, the selected
course is cancelled, and the course is selected as follow.
Fuzzy → Blanket →
Super Clean
2. During operating, all keys except for COURSE
SELECTION key are valid. But, only START/HOLD is
vaild during spin operation.
3. During operating, If any key is pressed after pressing the
START/HOLD key, new Selection course is performed,
not related to previous course.
4. This key is invalid during operation.
4-3-4 Function Button
1. This key is valid except for weight sensing operation.
2. After START/HOLD during operation or under reset
condition, as pressing this key display is changing as
follows.
Wash, Rinse, Spin, Soak → Wash → Rinse → Spin →
→
Wash, Rinse → Rinse, Spin → Wash, Rinse, Spin
3. The beginning conditions are as follows when function key
is selected. (ex.Maximum Level)
FUNCTION
WASH
RINSE
SPIN
WASH + RINSE
RINSE + SPIN
→ Speedy → Wool
TIME
18 min
15 min
11 min
38 min
26 min
7
4. This key is used as adjusting function.
① Rinsing times are added by one time when function
key is pressed under general course operation and
function operation as pressing this key.
Display is changing as follows.
2 (times) → 3 → 4 → 5 → 1
② Washing time is adjusted by press of function
key during washing only operation.
15(min) → 17 → 19 → 21 → 23 → 25 → 3 → 5 → 7 → 9 → 11 → 13
③ Spinning time is adjusted by press of function key
during spinning only operation.
7(min) → 1 → 2→ 3 → 4 → 5 → 6
4-3-5 Delay Start
1. This function is to finish the washing operation at the time user set.
2. If the START/HOLD key is pressed after adjusting of
reservation time by pressing the delay start button,
reservation washing begins.
3. If you push START/HOLD key after selecting reservation
washing, the machine carries out three-hour reservation
washing.
4. The first beginning value of reservation washing is 3 hour and
the order according to programacion key push is as follow.
3 → 4 → 5 →
5. Once reservation washing is selected, it follows the fuzzy
course selected and reservation washing can not be
changed in reservation procedure. But the change of
water level and water supply selection are possible.
6. If the door is opened in the waiting state of normal
reservation, it causes the door open error.
4-3-6 Start/Hold
1. Available only after selecting a course.
2. Sequence :
START → HOLD → START
3. The display shows the remaining time, including the
current function, when in 'start' status.
The time decreases 1-min at a time.
When in 'Hold' status, the time stays as it is.
4-3-7 Power
1) This key is always available when the power cord is connected.
2) sequence :
ON → OFF → ON
3) After finishing operation, this key is automatically turned off.
4-3-8 Silver Wash
1) This is a special function for washing by silver nano system.
2) The key can be pressed before the first press of
START/HOLD key
Silver ON → OFF → ON
3) Sequence :
...
→ 16 → 17 → 18
Hide quick links:
Advertisement
