Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for ZKTeco TL800
Summary of Contents for ZKTeco TL800
- Page 1 Installation Guide Model: TL800 Version: 1.0...
-
Page 2: Table Of Contents
Important Notes Please read this Installation Guide carefully and contact the Customer Care Service if you have any questions about the installation. To avoid any future service charges that can arise as a result of incorrect installation, it is recommended that installation can be performed by a professional technician to prevent any potential service charges that can occur due to incorrect installation. -
Page 3: What's In The Box
What's in the Box Mortise Outdoor Unit Indoor Unit Mounting Plate Keys Cards Strike Plate Lithium Battery and Box Cylinder Spindle A Spindle B Metal Pin Screw A Screw B Screw C Screw D Stud... -
Page 4: Installation Diagram
Installation Diagram OLED Screen Indoor Unit Door Screw C Outdoor Unit Lithium Battery Spindle A Screw D Metal Pin Stud Hidden Cover Metal Screw D Screw A Cylinder Spindle B Screw B Screw C Keys Screw A Mounting Plate Mortise Strike Plate and Box Front Handle Cover... -
Page 5: Drill Holes On The Door
Mortise StrikePlate StrikePlate Mortise Right Inward Left Inward Mortise StrikePlate StrikePlate Mortise Left Outward Right Outward User Location Adjust the Direction of Latch (if needed) Push the reverse block in upward direction. Push the bolt of the latch into the mortise. Rotate the latch bolt to 180°... -
Page 6: Install Mortise And Cylinder
Install Mortise and Cylinder Put the Mortise into the hole that was drilled, and secure the Mortise with Screw A. Insert the Cylinder into the Mortise ( the front sides and back sides) and secure it with Screw B. Screw A Screw B Front Front... -
Page 7: Install Studs And Outdoor Unit
Install Studs and Outdoor Unit Install the studs on the back of outdoor unit. Pass the outdoor unit cable through the upper most cable hole. Attach the Outdoor unit to the door by inserting the studs through the drilled holes. Place the Mounting Plate on the inside door and use Screw C to secure them. -
Page 8: Install Batteries And Cover
Install Batteries and Cover Insert Lithium Battery and cover them with an OLED Screen model, then push back the hidden cover. Install Strike Plate and Box Make sure that the Strike Box is aligned with the latch bolt. Then, use the installation template to drill the holes. -
Page 9: Physical Test
Physical Test Test the lock by using the mechanical key. Uncover the front handle cover from the bottom of outdoor unit, then rotate the cover 90°. Press the bottom of key hole cover and rotate it 180°. Insert the Key into key hole and rotate 90°, then the latches will be retracted. - Page 10 User Manual Model: TL800 Version: 1.0...
- Page 11 Important Notes TL800 is an intelligent Smart Lock. If the lock is not installed properly, it may affect the lifetime of the lock. We suggest you to install the lock after furnishing. Please prefer a professional technician to install the lock as per our installation standard.
-
Page 12: Product Overview
Product Overview Camera Lithium Battery Keypad & Card Detection Area Indicator Light Handle OLED Screen Model Fingerprint Hidden Cover Sensor (Hidden) Handle Mechanical Key Clutch Hole (Hidden) Double Locking Knob Emergency Power Quick Unlock Quick Close Button Interface (Micro USB) Button Front Handle Cover Definitions... -
Page 13: How To Use
Emergency Charging: The bottom of the outdoor unit is provided with a Micro-USB interface. Use a power bank to charge the lock when it is out of power. Emergency Mechanical Key: The mechanical key is used to open the door when the lock has electronic malfunction. -
Page 14: Register The First Administrator
Register the First Administrator Press and hold the Reset button for 5 seconds. The lock will beep for 5 times. Keep holding the Reset button until you hear the audio prompt, please press # key to confirm. Touch the keypad to activate the lock. Press the * # key to start the registration process. - Page 15 ∗ Delete by Number Delete by Fingerprint Delete by Password Delete by Card Complete Passageway Auto Lock Unlock Setting Latch Bolt Delay Anti-prying Detection Restore Factory Status Language Language/Volume Volume Date/Time Network Configuration...
-
Page 16: How To Use Oled Screen Model
How to use OLED Screen Model? Overview Up/Power Off Down/Back OK/Power On Programming the Features through Menu Mode Press Power On button to activate the model (camera mode). Press Down button to enter menu, choose Camera, Files or Set mode freely through buttons. - Page 17 Camera: Go to camera mode, customer can watch outside through the camera on outdoor unit. Files: All of photographs and videos are saved at here, before using this function, please insert a TF on this model. Set: It is used to set functions of this model. As below: Record Mode: Choose Photograph or Record (video) as records saving mode.
-
Page 18: How To Connect Usmart Go App
How to connect USmart Go APP? Setting Step 1: Download the App Search "USmart Go" on Apple App Store or Google Play Store on your iOS/ Android device. Step 2: Create an Account Launch the "USmart Go" App and register an account, you can register by your phone number or email address. - Page 19 Step 4: Setting Security Password You'll need to setup a security password for two-step verification. Following are the steps: Menu -> "My Settings" -> "Set security password". Step 5: Connect the Lock Lanuch the App, click “+ Add Device” button directly (only fit for no device before situation), or click the "ADD"...
- Page 20 Note: Please close WLAN on your phone setting page before connecting. Please select "No" or "Use" if your phone suggest you to switch to another Wi-Fi when connecting Wi-Fi. Step 6: Finish After getting connected, please go back to Connect hotspot page, and wait for the page until it goes to Select Wi-Fi page then connect a valid Wi-Fi and wait until finish.
- Page 21 Functions 1. Remote Unlock Guest Require: Press "Doorbell" key twice within 30s on the keypad to trigger a remote unlock request then you'll see a popup window on our app where you need to enter your security password to unlock. Owner self-unlock : Click the Unlock icon, you'll see a popup window on our app then enter your security password to verify and press the "Doorbell"...
- Page 22 2. Add User Click “Password” button on lock page, then click “+” on the top right corner to change to Add User page and fill out the authorizations information, then click “Next” to generate password. Note: Password is 7digits on the Generate password page, the last one is “1” by default.
- Page 23 3. Name the Lock Click the “More” button on the lock page, a popup window will be appeared, choose “Settings” to go to the Setting page, then click the Device Name to rename this lock and after finishing, click OK button. 4.
- Page 24 5. Check Records All of the event records are displayed on the lock page, customer can click them to check.
- Page 25 Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.