Related Manuals for Dormakaba Confidant RFID Kit 2
Summary of Contents for Dormakaba Confidant RFID Kit 2
- Page 1 Confidant RFID Kit 2 & Kit 3 (European Mortise Lock Case) Rose Mount & Back Plate Installation Instructions PK3649-T - 2021 - 09...
-
Page 3: Table Of Contents
: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Made in Canada dormakaba. All trademarks and registered trademarks are the property of their respective owners. © 2021 Confidant RFID Kit 2 & Kit 3... - Page 4 B - Screw Driver Phillips #1 & #2 C - Screw Driver Torx T-20 D - Hexagonal Key 3 mm E - 25mm / 24mm / 19mm / 12mm / 10mm Drill Bit F - Needle Nose Pliers Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21...
-
Page 5: Inventory
This one may be attached to lock A-Without Key Cylinder B-With Key Cylinder 3rd Party (Mortise & Cylinder) Warning: Install only on a mortise with anti-panic and an auxiliary dead latch (Anti-Pick system) Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 6: Rose Mount (No Key Override)
Inside Trim Inventory Kit Post may be with Thumbturn without Thumbturn attached to lock 3rd Party (Mortise) Warning: Install only on a mortise with anti-panic and an auxiliary dead latch (Anti-Pick system) Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 7: Back Plate Mount (Key Override)
Post may be attached to lock A-Without Key Cylinder B-With Key Cylinder 3rd Party (Mortise & Cylinder) Warning: Install only on a mortise with anti-panic and an auxiliary dead latch (Anti-Pick system) Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 8: Back Plate Mount (No Key Override)
Inside Trim Inventory Kit with Thumbturn without Thumbturn Post may be attached to lock 3rd Party (Mortise) Warning: Install only on a mortise with anti-panic and an auxiliary dead latch (Anti-Pick system) Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 9: Install Spindle
1- Check Handing: Adjust for Right Hand (RH) or Left Hand (LH) 2- Insert Spindle 3- Attach and Clamp Spindle Clip to Spindle as shown . Ensure legs are firmly clamped against the spindle Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 10: Install Outside Lever
Install Outside Lever Left Hand WARNING CAUTION IMPORTANT Hold down the outside lever against the outside housing while tightening the lever set screw. Right Hand Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 11: Align Posts With Mortise
Align Posts with Mortise (Rose Mount Only) WARNING CAUTION IMPORTANT Ensure Mortise lock case includes an anti-pick and anti-panic function Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 12: Adjust Handing
Handing RH to LH 1- Remove 2- Rotate 180˙ 3- Assemble Handing LH to RH 1- Remove 3- Assemble 2- Rotate 180˙ Prepare Inside Housing Inside Right Hand Housing Inside Left Hand Housing Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 13: Install Lock On Door
See Annex A for Exterior Applications Post may be attached to lock WARNING 3mm to 13mm CAUTION IMPORTANT After connecting all cables, make sure all excess cables are pushed inside the hole(s) in the door. Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 14: Rose Mount (Key Override)
• A always required • C recommended WARNING Screw M5 (5mm) 3mm to 13mm CAUTION IMPORTANT After connecting all cables, make sure all excess cables are pushed inside the hole(s) in the door. Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 15: Back Plate Mount (No Key Override)
See Annex A for Exterior Applications Post may be attached to lock WARNING CAUTION IMPORTANT After connecting all cables, make sure all excess cables are pushed inside the hole(s) in the door. Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 16: Rose Mount (No Key Override)
* Post may be attached to lock ** Recommended for more security WARNING CAUTION IMPORTANT After connecting all cables, make sure all excess cables are pushed inside the hole(s) in the door. Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 17: Install Inside Trim Cover
Install Inside Trim Cover Thumbturn must be vertical (if applicable) Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 18: Plug Battery Holder
F - Check Bolt Projection from Thumbturn & Key B - Check Green & Red Lights Flash C - Rotate Outside Lever to Check Bolt Retraction Program Lock With Jack Cable Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 19: Install Battery Door
For security reasons, lock must be programmed BEFORE installing the battery door. Every time the bat- tery door is removed pass an emergency card or connect lock to Kaba handheld programming device to reset the tamper alarm. Audit information is not affected. CAUTION IMPORTANT Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 20: Emergency Exit Device
0432 EN 179:2008 Emergency exit device Type 376B1452AD dormakaba Canada Inc. 7301 Decarie, Montreal, QC, Canada H4P 2G7 0432-CPR-00026_98 Capacity to trigger: Responds ( = < 70 N without load) Durability of capacity to trigger: Responds ( 200,000 cycles / = < 50 N without load) For declaration of performance, Fire resistance B - Automatic closing;... -
Page 21: Annex A • Install Outside Housing
Annex A • Install Outside Housing with Gasket and Cylinder Shield (Exterior and Ocean Front Versions) Model with Key Cylinder only Annex B • Remove Battery Holder Unscrew Remove Door Unclip Battery Holder Remove Battery Holder Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 22: Annex C • Install Bluetooth And Messenger Module
Annex C • Install Bluetooth and Messenger module Battery must be disconnected before adding Bluetooth and Messenger module. See annex D for instructions of how to remove the cover from the module. Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 23: Annex C • Install Bluetooth And Messenger Module
Orientation when Messenger Orientation when Messenger hub Position of Bluetooth hub outside the room inside the room antenna board NOTE: Battery must be connected last, after having connected the Bluetooth and Messenger module Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 24: Annex D • Remove Cover Of Bluetooth And Messenger Module
Annex D • Remove cover of Bluetooth and Messenger module DETAIL DETAIL SCALE 1:1 Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... -
Page 25: Annex E • Din Lever Installation
Annex E • DIN Lever Installation Confidant RFID Kit 2 & Kit 3 PK3649_T 09-21... - Page 26 USA Inc. Customer Services & Support Toll Free: 1.800.999.6213 International: +1 514 340 9025 General information: dormakaba.us Online consumable orders: dormakabalodgingstore.com To access all of our easy steps, please visit our support website: www.dormakabalodgingsupport.com www.dormakaba.com...
Need help?
Do you have a question about the Confidant RFID Kit 2 and is the answer not in the manual?
Questions and answers