Kirby Morgan M-48 MOD-1 User, Operator Course

Hide thumbs Also See for M-48 MOD-1:

Installation manual (8 pages)

User manual (56 pages)

page of 29

/ 29
Bookmarks

Quick Links

Download this manual

M-48 MOD-1

User/Operator Course

Summary of Contents for Kirby Morgan M-48 MOD-1

Page 2 FEATURES • Designed for: – Open Circuit SCUBA – Closed/Semi Closed SCUBA – Demand Mode Surfaced Supplied Diving • Pod system allows: – Diver Communications – Alternate Gas switching from any demand regulator – Gas Sharing and buddy breathing between divers ©...
Page 5 SCUBA POD WITH TILT TO PURGE • Can be paired with most second stage regulators • Requires a regulator with a mouthpiece tube that has a single lip © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 6 • Part #805-802 • Quarter-turn valve allows switching between closed and open circuit SCUBA • Kirby Morgan Balanced Second Stage Regulator with adjustment knob Primary used by Military and Technical Divers © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 10 INSTALLING KM MOUTHPIECE INTO POD • Insert mouth piece into pod first • Ensure mouthpiece is aligned evenly with the tube on the • Ensure correct alignment of the mouth piece on the inside (diver side) of the POD • Do not stretch the pod mouthpiece opening greater than 50%.
Page 12 Surfaced Supplied Diving • M-48 MOD-1 can be used for surfaced supplied diving • KM Manifold block (PN 300-145, 300-150, or 300-155) must be used for diver safety • Do not use without proper surfaced supplied training © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 13 Surfaced Supplied Diving • KM Manifold block The three part numbers are (PN 300-145, 300-150, for different umbilical or 300-155) adapters fittings on the non- return valve © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 15 Trimming Face Seal • Trim lines for face seal • Trimmed to fit different sized faces • Use sharp scissors • Trim one line at a time, test fit in between each • Refer to user guide for detailed instructions ©...
Page 16 • Comms available as an option for the M48 • Minor modification done by owner required to install comms • Refer to Kirby Morgan manuals and user guides for the M-48 for additional instructions. • Video instructions available on KMDSI website...
Page 19 Installing Neoprene Hood • Fully assembled hood incorporated into mask • Excellent option for cold water diving • Hoods that are permanently attached to dry suits can still be used © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 21: Donning The Mask
Donning the Mask Place on face Loosen all straps Tighten temple straps first and the alternate between temple and jaw straps © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 22 Attaching Pod to Mask Practicing the correct procedure to gain confidence before diving will ensure diver safety and comfort while using the M-48 © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 23 Attaching Pod to Mask • Connect pod hook to fastener on left side of mask • Swing pod to the right towards the pod catch • Ensure pod clicks into the second tooth of the pod catch © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 24 Attaching Pod to Mask Thumb and index finger method of connecting to pod catch Fingers and palm method of connecting to pod catch © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 25 Release Pod from Mask • Squeeze front and back of the pod catch simultaneously • Swing pod forward and to the left to release it from the mask Practice, Practice, Practice! © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...
Page 26 Mask Clearing and Dewatering • To clear water from the upper eye section clear the mask in the same procedure as you typically would in any SCUBA mask while in the upright position • Water will leave the upper portion of the mask to the lower cavity and will...
Page 27 Post Dive Procedures • Post dive procedures are the same for all SCUBA related equipment • Wash with soap and water if needed • Thoroughly rinse with fresh water • Allow to dry • Properly store • Refer to user guide for detailed instructions ©...
Page 28: Safety Recommendation
Safety Recommendation Kirby Morgan recommends that all users make at least a 30 minute indoctrination dive prior to open water diving the M-48 MOD-1 © 2021 Copyright Dive Lab® Inc. All rights reserved. Rev 19 Oct 2021...

Kirby Morgan M-48 MOD-1 User, Operator Course

Quick Links

Related Manuals for Kirby Morgan M-48 MOD-1

Summary of Contents for Kirby Morgan M-48 MOD-1

Page 21: Donning The Mask

Page 28: Safety Recommendation