Daikin Altherma 3 R W Installer's Reference Manual page 291

10/11
Field settings table
Breadcrumb Field code Setting name
9.I [C-0A] --
9.I [C-0B] --
9.I [C-0C] --
9.I [C-0D] --
9.I [C-0E] --
9.I [D-00] Which heaters are permitted if prefer. kWh rate PS is cut?
9.I [D-01] Contact type of preferential kWh rate PS installation?
9.I [D-02] Which type of DHW pump is installed?
9.I [D-03] Leaving water temperature compensation around 0°C.
9.I [D-04] Is a demand PCB connected?
9.I [D-05] Is the pump allowed to run if prefer. kWh rate PS is cut?
9.I [D-07] Is a solar kit connected?
9.I [D-08] Is an external kWh meter used for power measurement?
9.I [D-09] Is an external kWh meter used for power measurement?
9.I [D-0A] --
9.I [D-0B] --
9.I [D-0C] --
9.I [D-0D] --
9.I [D-0E] --
9.I [E-00] Which type of unit is installed?
9.I [E-01] Which type of compressor is installed?
9.I [E-02] What is the indoor unit software type?
9.I [E-03] What is the number of backup heater steps?
9.I [E-04] Is the power saving function available on the outdoor unit?
9.I [E-05] Can the system prepare domestic hot water?
9.I [E-06] Is a DHW tank installed in the system?
9.I [E-07] What kind of DHW tank is installed?
9.I [E-08] Power saving function for outdoor unit.
9.I [E-09] --
9.I [E-0A] --
9.I [E-0B] Is a bi-zone kit installed?
9.I [E-0C] --
9.I [E-0D] Is glycol present in the system?
9.I [E-0E] --
9.I [F-00] Pump operation allowed outside range.
9.I [F-01] Above which outdoor temperature is cooling allowed?
9.I [F-02] Bottom plate heater ON temperature.
9.I [F-03] Bottom plate heater hysteresis.
9.I [F-04] Is a bottom plate heater connected?
9.I [F-05] --
9.I [F-09] Pump operation during flow abnormality.
9.I [F-0A] --
9.I [F-0B] Close shut-off valve during thermo OFF?
9.I [F-0C] Close shut-off valve during cooling?
9.I [F-0D] What is the pump operation mode?
4P629091-1B - 2021.02
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/O
R/O
R/W (*6)
R/O (*7)
R/O
R/O
R/W
R/O
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(#) Setting is not applicable for this unit.
Range, step
Default value
0
0
0
0
0
0: None
1: BSH only
2: BUH only
3: All heaters
0: No
1: Active open
2: Active closed
3: Smart grid
0: No
1: Secondary rtrn
2: Disinf. Shunt
0: No
1: increase 2°C, span 4°C
2: increase 4°C, span 4°C
3: increase 2°C, span 8°C
4: increase 4°C, span 8°C
0: No
1: Pwr consmp ctrl
0: Forced off
1: As normal
0: No
1: Yes
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
0: No
1: 0,1 pulse/kWh
2: 1 pulse/kWh
3: 10 pulse/kWh
4: 100 pulse/kWh
5: 1000 pulse/kWh
6: 100 pulse/kWh (PV meter)
7: 1000 pulse/kWh (PV meter)
8: 1 pulse/m³ (gas meter)
9: 10 pulses/m³ (gas meter)
10: 100 pulses/m³ (gas meter)
0
2
0
0
0
0~5
0: LT split
0
0: Reversible (*6)
1: Heating only (*7)
2: 3V (*1)
3: 6V (*2)
4: 9W (*3)
0: No
1: Yes
0: No (*4)
1: Yes (*5)
0: No
1: Yes
0~6
0: EKHW (*4)
1: Integrated (*5)
5: EKHWP (*4)
0: Disabled
1: Enabled
1
0
0
0
0
0
0: Disabled
1: Enabled
10~35°C, step: 1°C
20°C
3~10°C, step: 1°C
3°C
2~5°C, step: 1°C
5°C
0: No
1: Yes
0
0: Disabled
1: Enabled
0
0: No
1: Yes
0: No
1: Yes
0: Continuous
1: Sample
2: Request
Installer setting at variance with
default value
Date Value
(*1) *3V_(*2) *6V_
(*3) *9W_(*4) EHB*_
(*5) EHV*_
(*6) *X*_(*7) *H*