Related Manuals for Schulze BluePRESSLine CAP
Summary of Contents for Schulze BluePRESSLine CAP
- Page 1 Instruction manual Version 11.01 heat press BluePRESSLine Version 11.01 1 / 13...
-
Page 2: Table Of Contents
1. Introduction 1.1 Content 1. Introduction 1.1 Content 1.2 Illustration of the heat press 1.3 Technical data 1.4 Safety arrangements of the heat press 1.5 Safety arrangements at the workspace 2. Initiation 2.1 Tips for transport 2.2 Installation of the heat press 2.3 Power supply 2.4 Initiation of the heat press 3. -
Page 3: Illustration Of The Heat Press
Illustration of the heat press electronic devices contact pressure adjustment base plate turnbuckle heating plate main switch pressure lever with power grip 10. main fuse cable with connector 11. gas pressure spring 150 N turnbuckle lever 12. spiral tube Technical Data Dimensions of the press: …...... -
Page 4: Safety Arrangements Of The Heat Press
If any irregularities regarding functionality or safety are found during the testing, these have to been noted and reported to Walter Schulze GmbH in written form within 7 days. Until clarification the press can not be used. -
Page 5: Initiation
2.3 Power supply The BluePRESSLine CAP has to be connected to a voltage of 230VAC/ 50Hz. The press is equipped with a plug. Make sure that the power outlet is in the right condition and that the grounding is connected to the power outlet. -
Page 6: Working With The Heat Press
3. Working with the heat press 3.1 Programming of electronic device After switching on the press, the current temperature is shown on the display and the press heats up. Change settings: The programming mode shows up when you press Button 1 for about 5 seconds, until the LED blinks up. LED1 blinks and the programmed temperature shows up on the display. -
Page 7: Application Range And Sample Adjustments Of The Heat Press
3.2 Application range and sample adjustments of the heat press This press is used to put transfers and transfer films on textiles. To get good achievements, get in contact with the producer of the textiles. Here are some settings: Film Flex 150°C –... -
Page 8: Maintenance
4. Maintenance 4.1 Daily Maintenance The working surface of the heating plate and the base plate have to be clean. The heating plate can be cleaned with a clean, dry cloth. Avoid contact with the heating plate – risk of burns. The silicon gum can be cleaned with a soft cloth. You can use mild household detergent. -
Page 9: Replacing The Main Fuse
4.3 Replacing the main fuse If the heat press does not work after switching on, check the main fuse of the press. The main fuse 10 A is placed at the right side of the heat press (photo 1). To exchange the fuse, switch off the heat press first and pull the plug. -
Page 10: Replacing The Thermal Fuse
4.6 Replacing the thermal fuse For the exchanging of the thermal fuse, the press must be disconnected from the electricity and cold. Release the screw on top of the heating plate (photo 1), place it on the base plate (photo 2) and unscrew the four screws in the heating plate (photo 3). Thereby mind the springs. -
Page 11: Troubleshooting
4.8 Troubleshooting Problem Cause Debugging main fuse 6 A is defect Exchange main fuse 6 A Green switch blink, but: If main fuse is okay, than check Exchange electronic devices display doesn´t glow plate doesn´t heat thermal fuse on heatplate is defect Exchange thermal fuse heatpress doesn´t heat up to adjusted temperature even if the red diode glows... -
Page 12: Connection Diagram
4.9 Connection diagram Version 11.01 12 / 13... -
Page 13: Testing Report
EN 292-1 EN 292-2 safety of machines EN 60204-1 electrical equipment of machines Berlin , .._____________________________ Peter Meidinger President All SCHULZE heat presses are excempt from the waste disposal law under reg.no. DE 231060054. Version 11.01 13 / 13...
Need help?
Do you have a question about the BluePRESSLine CAP and is the answer not in the manual?
Questions and answers