Pump Parts List - Liquiflo POLY-GUARD Series Installation, Operation & Maintenance Manual

Liquiflo Installation, Operation & Maintenance Manual
Appendix 2: Pump Parts List
Ref. #
1 * Idler Shaft
2 * Drive Shaft
3 * Idler Gear (Spur Type)
4 * Drive Gear (Spur Type)
5 * Retaining Ring, Gear
6 * Bearing (Sleeve Type)
7 * Pin, Bearing Lock
8 * Wear Plate (Relieved Type)
9 Rear Housing (PFA-Lined)
10 * O-Ring, Housing
11 * Pin, Housing Alignment
Center Housing, Flanged
12
(PFA-Lined)
13 * Key, Gear
14 * Key, Inner Magnet
15 Front Housing (PFA-Lined)
16 Bolt, Housing
17 Setscrew, Hub, Outer Magnet
18 Inner Magnet (PFA-Lined)
19 * Retaining Ring, Inner Magnet
20 Containment Can (PTFE-Lined)
21 Screw, Containment Can (5/16-24 X 5/8 SHCS)
22 * O-Ring, Containment Can (Size 2-042)
23 Hub, Outer Magnet
24 Outer Magnet
25 Pedestal (Mounting Bracket)
26 Bolt, Front Housing
27 Nut, Front Housing (3/8-16)
28 Lockwasher, Front Housing (3/8)
29 Bolt, Motor Mounting (3/8-16 X 1 SHCS)
30 Adapter Plate (See Appendix 1) [Not Shown]
31 Bolt, Adapter Plate (See Appendix 1) [Not Shown]
*
Item included in a standard Poly-Guard Series Repair Kit.
simply place a "K" in front of the Pump Model Number to designate the Kit Order Number. Example: KP4UPPEE110BVU.
Using this order number will ensure that the kit component materials will match those used in the pump. (See pages 5 and 6
for Model Coding information.)
1 For Models P1-P4, one Retaining O-ring is required for the Drive Gear; two are required for the Idler Gear.
2 Part included with Outer Magnet Assembly (Ref. # 24).
3 For NEMA 56C thru 184TC motor frames. For bolts for IEC motor frames, see Appendix 1.
NOTE: Reference Numbers above correspond to Reference Drawings on pages 27 and 28. For Liquiflo Part Numbers, refer
to Poly-Guard Series Consolidated Bill of Materials (BOM).
Parts List for Poly-Guard
Part Description
Models P1-P4: O-Ring, Size 2-013
Models P5-P9: O-Ring, Size 2-017
Models P1-P4: Size 2-037
Models P5-P9: Size 2-043
Models P1-P4: 3/4" ANSI 150# or DN-20 PN16
Models P5-P9: 1-1/2" ANSI 150# or DN-40 PN16
Models P1-P4: 5/16-18 X 2-1/2 SHCS
Models P5-P7: 5/16-18 X 3-1/4 SHCS
Models P8-P9: 5/16-18 X 4-1/2 SHCS
2
Models P1-P4: O-Ring, Size 2-012
Models P5-P9: O-Ring, Size 2-013
2
Models P1-P4: 3/8-16 X 1-1/2 SHCS
Models P5-P9: 3/8-16 X 1-5/8 SHCS
3
To order a Repair Kit for an existing Poly-Guard Series pump,
26
®
Poly-Guard Series MAG-DRIVE Gear Pumps
Models P1 thru P9, Close-Coupled
®
Series Pumps
1
Quantity
1
1
1
1
3
4
4
4
4
1
2
4
1
2
1
1
4
8
8
2
1
1
1
6
1
1
1
1
4
4
4
4
1
4