Page 1
S3 40 0- 24 T4 LnK /Ac t COM BO RES ET Po E CON SOL E SFP + Po E SWA P CON SOL E PW R PoE+ Series Switches 8/16/24/48 PORT GIGABIT L2+ POE+ MANAGED SWITCH Quick Start Guide...
Page 2
Introduction Thank you for choosing PoE+ Series Switches. This guide is designed to familiarize you with the layout of the switches and describes how to deploy the switches in your network. S3150-8T2FP S3260-8T2FP Lnk/Act S3260-16T4FP CONSOLE Lnk/Act S3260-16T4FP RESET COMBO...
Front Panel Button S3150-8T2FP/S3260-8T2FP RESET S3260-16T4FP Lnk/Act CONSOLE Lnk/Act S3260-16T4FP RESET COMBO RESET S3400-24T4FP COMBO LnK/Act CONSOLE LnK/Act S3400-24T4FP RESET RESET Button Description Restart and restore factory default settings. Reset S3400-48T8SP SFP+ SFP+ RESET SWAP CONSOLE CONSOLE SWAP Button Description Press the button and the indicator is on, and the indicator will automatically turn o after a while.
Front Panel LEDs Lnk/Act COMBO LnK/Act CONSOLE LnK/Act S3400-24T4FP RESET LEDs Status Description Switch is powered on. Blinking Green System is working properly. ON/OFF System is working not properly. Blinking Green Data is being transmitted or received. Lnk/Act ON/OFF Connection is not connected. Connected PD device, working properly.
Site Environment: Do not operate it in an area that exceeds an ambient temperature of 50ºC. The installation site must be well ventilated. Ensure that there is adequate air fow around the switch. Be sure that the switch is level and stable to avoid any hazardous conditions. Do not install the equipment in a dusty environment.
2. Attach the switch to the rack using four M6 screws and cage nuts. Grounding the Switch 1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the switch is mounted. 2.
Connecting the Power 1. Plug the AC power cord into the power port on the back of the switch. 2. Connect the other end of the power cord to an AC power source. WARNING: Do not install power cables while the power is on. Connecting the RJ45 Ports 1.
Connecting the SFP/SFP+ Ports 1. Plug the compatible SFP/SFP+ transceiver into the SFP/SFP+ port. 2. Connect a ber optic cable to the ber transceivers. Then connect the other end of the cable to other ber devices. WARNING: Laser beams will cause eye damage. Do not look into bores of optical modules or optical bers without eye protection.
Page 10
Con guring the Switch Con guring the Switch Using the Web-based Interface Step 1: Connect the computer to any Ethernet port of the switch using the network cable. Step 2: Set the IP address of the computer to 192.168.1.x. ("x" is any number from 2 to 254.). Set the subnet mask of the computer to 255.255.255.0.
Quick Connect Protocol: Serial Flow Control Port: COM3 DTR/DSR 115200 Baud rate: RTS/CTS Data bits: XON/XOFF Parity: None Stop bits: Name of pipe: Show quick connect on startup Save session Open in a tab Connect Cancel Step 4: Enter the default username and password, admin/admin. Troubleshooting Loading Failure Troubleshooting After loading fails, the system will keep running in the original version.
Con guration System Troubleshooting 1. Make sure the power supply is normal and the console cable is properly connected. 2. Check if the console cable is the right type. 3. Check if the control cable driver is properly installed on the computer. 4.
Mission Statement BZBGEAR manifests from the competitive nature of the audiovisual industry to innovate while keeping the customer in mind. AV solutions can cost a pretty penny, and new technology only adds to it. We believe everyone deserves to see, hear, and feel the advancements made in today’s AV world without having to break the bank.
Need help?
Do you have a question about the PoE+ Series and is the answer not in the manual?
Questions and answers