Table of Contents
Advertisement
Alarm 1 Silencing 32, 71
Alarm 2 High 39, 42
Alarm 2 Hysteresis 32, 71
Alarm 2 Latching 32, 71
Alarm 2 Logic 32
Alarm 2 Low 39, 42
Alarm 2 Message 32
Alarm 2 Silencing 32, 71
Alarm 3 High 39, 42
Alarm 3 Hysteresis 33, 71
Alarm 3 Latching 33, 71
Alarm 3 Logic 33
Alarm 3 Low 39, 42
Alarm 3 Message 33
Alarm 3 Silencing 33, 71
Alarm High 1 Status 25
Alarm High 2 Status 25
Alarm High 3 Status 25
alarm hysteresis 71
alarm latching 71
Alarm Low 1 Status 25
Alarm Low 2 Status 25
Alarm Low 3 Status 25
alarm message 21
alarm set points 70
alarm silencing 71
Ambient Temperature 59
ambient temperature 76, 77
Ambient Temperature Error 76
Analog Output 1 Scale High 29
Analog Output 1 Scale Low 29
Analog Output 1 Units 29
Analog Output 3 Units 31
Auto-Manual Control Indicator
Light 20
Auto-Manual Mode 36, 40, 67–68
automatic mode 21
Autotune 36, 40
autotune 63, 75
Autotune Aggressiveness 34, 64
Autotune Enable 64
auto (closed loop) 66–67
B
B&B Converters 18
back views 10
Baud Rate 34, 71, 72
baud rate 3
biasing and termination 18
C
calibration 76
offset 64–65
restoring factory 60
Wat lo w Se rie s S D
Wat lo w Se rie s S D
Series SD Calibration Manual 24
Calibration Offset 36, 40
Checksum Error 76
closed loop control 20, 66
Closed Loop Set Point 25
CMC Converter 18
Comm7 72
communications 71, 78
control methods 66–70
Control Method 1 28
Control Method 2 30
Control Method 3 31
Cool Control Method 37, 41, 67–68
Cool Hysteresis 38, 41
Critical damped 64
Current Ramp Set Point 25
D
Dead Band 41
dead band 68
Dead Band Cool 38, 68
Dead Band Heat 37, 68
Default Parameters 59
Derivative 41
Derivative Cool 38, 68
Derivative Heat 37, 68
Derivative Term 38, 41
dimensions 78
1/16 DIN 4
1/32 DIN 4
1/4 DIN 5
1/8 DIN 5
displays 20–24
display fl ashes 52, 75
Display Intensity 59
E
editing a profi le 52
EEPROM 73
EIA-232 19
EIA-232 port 72
EIA-485 19
EIA/TIA-232 71
EIA/TIA-232 to EIA/TIA-485 con-
verters 18
EIA/TIA-485 11, 19, 71, 74, 78
EIA/TIA-485 serial port 72
Elapsed Jump Count 57
electrical noise (RFI) 70
electromechanical relay 78
EM00-GATE-0000. See EM Gate-
way
EM Gateway 19
End 50
81
81
•
•
•
•
End Set Point Value 57
End Step 50, 53
error condition 21
Ethernet Gateway. See EM Gateway
Event Output 1 38, 48, 49
Event Output 1 status 57
Event Output 2 38, 48, 49
Event Output 2 status 57
Event Output 3 38, 48, 49
Event Output 3 status 57
F
Factory Page 24, 59
Failed File Number 57
Failed Step Number 57
File 47
Filtered Process Value 25
fi lter time constant 65
Filter Value 28, 65
Fixed Time Base 1 (Cycle Time) 28
Fixed Time Base 2 (Cycle Time) 30
Fixed Time Base 3 (Cycle Time) 31
functionality matrix 78
G
Greenlee 4–5
Guaranteed Soak 53
Guaranteed Soak Deviation 53
Guaranteed Soak Deviation Enable
34, 56
Guaranteed Soak Deviation Mes-
sage 56
Guaranteed Soak Deviation Value
34, 56
H
Heat Control 36, 40
Heat Control Method 67
Heat Hysteresis 37, 41
high range 66
holding and resuming a profi le 52
Home Page 25
Hours 48, 49
Hours Remaining 57
I
IDC. See Infrared Data Communi-
cations (IDC)
independent heat and cool PID 69
Infi nity Key 20
INFOSENSE™ 26
INFOSENSE™ temperature sens-
ing 2, 64
Chapter 1 Ov e r v i ew
Appe ndix
Advertisement
Table of Contents
