Chasing Light Control Board Page 26 10.5 Window Light Control Board Page 27 10.6 3-Color Chasing Light Control Page 27 Parts List Page 28-36 Warranty Page 37 Calling for Service Page 39 Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 4
Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
NTRODUCTION 2.1 Overview: Thank you for purchasing the new Rescue 1™ from Bob's Space Racers ® . Built on a long tradition of value, the new Rescue 1 retains all of the great game play you have come to expect of a game from BSR, and is specifically designed for today's Arcade environment. The new game uses technology specifically developed for this application.
This product is heavy, necessitated by the design. When moving this game, be sure you have adequate help. Use a suitable dolly or hand truck where practical. Use back support when needed. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
LED Bulb 12V LED Bulb 4 pcs LED Bulb Replacement for LED Bulb 2 pcs START button Water Water Filter (20 Micron) 1 pc Filter Filter Filter Handle 1 pc Handle Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
16 Ga. and no longer than 20 ft. Check the label on the back of the game to make sure the power requirements of the game match that of your location. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Phillip’s head bolts that were removed in Step 2. Ensure that the wiring and plug do not get pinched while securing the light tube. Tighten all Phillip’s head bolts into place. 6. Repeat steps 2-6 for remaining light tubes. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
When moving the game, DO NOT slide the game across the floor Ensure the game is level before connecting the power Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
2. Slightly raise the seat base and guide the slide lock opening onto the tabs and then lower the seat base. 3. This will lock the seat bases into place. Seat Base Slide Lock Bracket Game Cabinet Retaining Bracket Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
DO NOT operate the game with no or too little water in the game. This will cause the water pump to overheat and potentially burn up. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Operate this game with the correct power and fuse configuration. (The machine’s supply Voltage is 110VAC, please refer to the label on the machine, connect the actual supply voltage, if not, it can cause an electric shock or malfunction.) Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
NOTE: SW1, SELECT, and one (1) time, it will coin ERASE Buttons do not up Player 1. If pressed have a function. two (2) times it will coin up Player 2. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
3. Press the ENTER button to increase the option setting to preferred value. ADDRESS VALUE SETTING VALUE 4. When all wanted values are changed, Value press the TEST button until the game returns to PLAY MODE. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Use a good quality spray type furniture polish to keep the game looking good. Use a good quality glass cleaner to clean and polish the glass portions of the game. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Do not use any form of chemical cleanser or deionized distilled water to put into the game. CHANGE WATER BUTTON DRAIN TUBE VALVE: Clockwise = CLOSE Counter-Clockwise - OPEN PUMP DRAIN TUBE BUCKET Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
The indicator will light when water needs to be added to the game. LOW/NO WATER INDICATOR Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Monthly Maintenance Water quality Change the water filter for the game. Lights Check for bad light bulbs and replace. Game function Check for proper game function and repair as needed. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
6. When changing electronic or electrical components, ALWAYS turn off and unplug the game. 7. Check to see that all power supplies are delivering the specified voltages to the P.C. Boards and components as shown in the manual. Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
The fuse is bad Replace the fuse The voltage output of the Increase the voltage output power supply is too low to 5.2V Main board is bad Replace the main board Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
10. G IAGRAMS 10.1 Electronic Assembly: Main Board Sound Board Window Light 3-Color Chasing Control Boards Light Solid State Relay Chasing Light Power Supplies Drive Board 10.2 Main Board: Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
10. G IAGRAMS ONTINUED 10.3 Sound Board: Volume Control 10.4 Chasing Light Control Board: Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
11. P ARTS DESCRIPTION PART NUMBER PHOTO Main Board Sound Board E0801902 Chasing Light E0801904 Control Board Window Light E0801903 Control Board 3-Color Chasing E0801909 Light Control Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 29
Solid State Relay Settings Board Coin Mech Electric Water Valve Ticket Dispenser Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 30
Filter Housing Power Cord 10 Amp Fuses #1285 Key #1396 Key 12V LED Bulb Replacement Bulb for Start Button 20 Micron Sediment Filter Filter Handle Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 31
Change Water Button Start Button Water Gun Window Target Low Water Indicator Time Display Cover Plate Player 1 Score Display Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 32
Speaker Bonus Display Ladder M0801908 Small LED Light E0801910 Cover (RED) Small LED Light E0801911 Cover (YELLOW) Large Light Cover E0801908 (YELLOW) Rail M0801914 Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 33
Lighted Trim Side Rail M0801912 Fireman Figure M0801902 Clown Figure M0801903 Fire Hydrant Figure Side Tempered M0801904 Glass Shield Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 34
Top Plexiglas Shield Marquee “RESCUE” Sign E0801913 Marquee Acrylic M0801910 Panel Power Cord Input Water Pump Player 1 Vinyl Decal Player 2 Vinyl Decal Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 35
Player 2 Coin Vinyl Decal Tickets Vinyl Decal Rubber Gun Boot M0801913 Light Board E0801905 Display Board E0801906 Light Board of E0801907 Light Gun Tip M0801901 Acrylic Ladder M0801907 Holder Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 36
M0801909 Plastic Cover for M0801911 Water Tank Fiberglass Seat – Complete M0801915 Assembly Metal Brackets M0801916 for Top Glass How To Play Vinyl Decal Tube Only M0801906 Lighted Tube End Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Bob’s Space Racers , Inc. to the original purchaser. Telephone or write: ® Bob’s Space Racers , Inc. 427 15 Street Daytona Beach, FL 32117 Telephone number: 386/677-0761 FAX: 386/677-0794 Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Page 38
Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
IF YOU HAVE ANY QUESTIONS OR COMMENTS, PLEASE CALL OUR SERVICE DEPARTMENT AT (386) 677-0761 (MONDAY – FRIDAY, 8:30AM – 5:00PM EST, EXCLUDING HOLIDAYS) (or) Tech@BobsSpaceRacers.com EMAIL QUESTIONS TO: (or) VISIT THE “CUSTOMER SUPPORT” SECTION ON OUR WEBSITE: WWW.BOBSSPACERACERS.COM Bob’s Space Racers Inc. | Rescue 1™ Operator’s Manual (V1.SEPT2014)
Need help?
Do you have a question about the Rescue 1 and is the answer not in the manual?
Questions and answers