Cleaning And Maintenance - Concept2 OV2010 Manual

EN
Humidity setting
The buttons are used to set the desired humidity in SMART mode. The desired
humidity can be set between 40 % - 85 %. When the desired humidity is set to
35 %, the dehumidifier will dehumidify until the water tank is full.
Humidity indication setting
Press this button to turn on the colour indication on the front panel of the
dehumidifier. The colour of the lighting changes according to the measured
humidity.
If the humidity is less than 60 %, the dehumidifier lights up blue - low humidity
If the humidity is between 61 % and 70 %, the dehumidifier lights up green - ideal
humidity
If the humidity is greater than 71 %, the dehumidifier lights up red - high humidity
UV lamp
Press the "UV" button to turn on the UV lamp function, the LED indicator next to
the button lights up. Press again to turn off the UV lamp, the LED goes out.
Timer
Press the button to set the timer function. If the timer is active, the LED next to the
timer button is lit. Before setting the timer, make sure that it is not already set. (LED
must be off) The timer has the following functions:
Shut-down timing
If the appliance is switched on and set according to your requirements, press the
"Timer" button. Use the up/down control buttons to set the time for which the
appliance should run (1-24 hours).
Switch-on timing
If the appliance is in standby mode, you can set the switch-on timer. Press the
"Timer" button and use the up/down buttons to select the time in which you want
the appliance to switch on (1-24 hours).
Intelligent defrosting
The appliance automatically starts defrosting if the sensor detects that the
ambient temperature is too low. The "Defrost" LED indicator lights up during
defrosting. Once the defrost process is completed, the appliance returns to the
mode in which it operated.
Water tank full
As soon as the water tank is full, the "Tank full" LED indicator lights up and the
appliance stops working. After emptying the tank and placing it correctly in the
appliance, the appliance continues in the mode in which it operated.
Ioniser
Press the "Plasma Ioniser" button to turn on the Ioniser function to remove
bacteria, the LED indicator next to the button will light up. Press again to turn off
the Ioniser, the LED goes out.
Note:
When the humidity level drops by 2 % below the desired value. The dehumidifier interrupts its operation. However,
the ventilator will still run for 5 minutes to cool the dehumidification unit. Then it interrupts its operation. After 30
minutes, the dehumidifier checks whether the humidity has risen and, if so, resumes operation. If the humidity is still
less or equal to the desired value the dehumidifier will wait another 30 minutes.
58
WARNING:
• The efficiency of the unit is influenced by the air quality in the room of operation. To get the best results when
dehumidifying, do not open and close the windows and doors too often.
• Use the dehumidifier in the designated operation temperature to ensure proper functionality of the unit. For safety
reasons, dehumidification automatically stops and the air purification function is launched instead if the ambient
temperature rises above than 36 °C.
• When putting the unit in operation, the circulation of the coolant inside the appliance may produce noises. As the
circulation stabilizes, the noise level decreases.
• After switching off the dehumidifier, do not switch it on for at least 5 minutes. This prevents damage to the
compressor.
• For example, if there is a power failure, the compressor will not turn on immediately after the appliance turns on.
For safety reasons, it does not switch on until 3 minutes later.
• The appliance is intended for indoor use.
• Do not place the dehumidifier opposite radiators or other heat sources.

CLEANING AND MAINTENANCE

• To prevent electric shock, never connect or disconnect the plug with wet hands
• Prior to cleaning or maintenance, first switch the appliance off and disconnect it from the mains.
• Do not remove the float lever from the water tank.
• To prevent device malfunctions or excessive noises, keep the unit in the upright position.
• Wipe the body of the appliance with a soft, dry cloth.
• Use a soft, moist (well wrung) cloth to remove larger dirt deposits. Never use a damp cloth to clean the control
panel.
• To avoid any deformation or cracking, do not use gasoline, thinner or other liquid detergents.
• Chemicals can cause colour changes of the surface of the appliance.
If you are not going to use the appliance for a prolonged period of time:
1. Unplug the unit, wind the power cord up, and hang it on the back of the appliance.
2. Empty the water tank, wipe it with a cloth and return it to the unit.
3. Clean the air filter.
4. Store the unit in upright position, do not place it on its side or back and avoid direct sunlight.
How to empty the water tank
1. Remove the tank from the unit.
2. Grasp the tank by the handle and move it gently.
3. Tilt the tank and carefully drain water out.
4. Put the tank back in the unit.
Note: Water is collected in the tank during the operation. When the tank is full, the dehumidifier will stop automatically,
the "Tank full" LED indicator will flash and the LED humidity indicator will flash red.
OV2010 OV2010
EN
59