Page 1
Instruction manual June 2017 MTL industrial ethernet INM 9661-ETW Rev 1 9661-ETW MTL intrinsically safe ethernet to serial 4 port communication module...
Page 2
DECLARATION OF CONFORMITY A printed version of the Declaration of Conformity has been provided separately within the original shipment of goods. However, you can find a copy of the latest version at - http://www.mtl-inst.com/certificates INM 9661-ETW Rev 1...
9661-ETW MTL Intrinsically Safe Ethernet to serial 4 port communication module INTRODUCTION The 9661-ETW is an Intrinsically Safe (IS) Ethernet to Serial 4 Port Communication Module suitable for Zone 0 mounting with a suitable Ex ia Power Supply. The Module allows existing Intrinsically Safe equipment with an RS485/RS422 or RS232/TTL port to become Ethernet Enabled via either Wi-Fi (WLAN) or a Cat5/6 cable connection into an IS Ethernet Network (LAN).
INSTALLATION This Equipment must be installed, operated and maintained only by trained competent personnel and in accordance with all appropriate international, national and local standard codes of practice and site regulation for intrinsically safe apparatus and in accordance with the instructions contained here. The 9600-ET Ethernet I/O module range is designed in accordance with general electrical safety standards e.g.
4 .1 Special conditions for safe use (Conditions of certification) The following conditions relate to safe installation and/or use of the equipment, this is an extract from the certificate CML 16ATEX2131X. 14.1 When used with Group I gases and Group III dust, the modules shall each be mounted within an enclosure providing a degree of protection of at least IP54.
CONNECTING THE 9661-ETW TO A PC/NETWORK 5 .1 Connecting with LAN • Ensure that the 9661-ETW unit is powered by a suitable IS supply, such as the MTL 9492-PS. PoEx can be used to power the unit via LAN port 2 if required.
• This page shows the current configuration of the 4 Comms ports. CONFIGURING WI-FI NETWORK SETTINGS • Click on the Wi-Fi Information menu option and you will see the screen below This shows information about the Wi-Fi module and the current settings associated with it, including whether there is an active Wi-Fi connection.
Page 11
SSID – This should be configured to the same SSID as your access point / • router you want the unit to connect to. • Authentication – This enables WPA/WPA2-PSK security on the Wi-Fi link and is the recommended setting. The only other option is Open where no security is used.
SETTING UP THE 9661-ETW COMMS PORTS To change any of the settings this is done in the following step Click on the Wi-Fi Configuration menu option, this prompts the user to • enter a username and password. The defaults are shown below, both are case sensitive –...
• Byte Timeout determines the end of a slaves reply as when another byte is not received during this time. (typically set between 2ms and 20ms depending upon Baudrate) • Poll Delay slows down the packet rate if required. (Default is 0ms) •...
For more detailed information about take-back and equipment recycling please contact your local Eaton MTL representative. CONFORMITY Refer To 9600 Series Declaration of Conformity MAINTENANCE...
CERTIFICATION Ex ia I Ma Ex ia IIC T4 Ga [Ex ia Da] IIIC T135ºC CML 16ATEX2131X IECEx CML 16.0053X See Certificates for further information 13 .1 Marking details ® MTL 9600 Series Ethernet I/O Module Serial No. 17/0001 9661-ETW MTL IS 4-Port Serial Gateway Part No.
Page 16
Cooper Electric (Shanghai) Co. Ltd 955 Shengli Road, Heqing Industrial Park SINGAPORE Pudong New Area, Shanghai 201201 Eaton Industries Pte Ltd 100G Pasir Panjang Road, Interlocal Centre Tel: +86 21 2899 3817 Fax: +86 21 2899 3992 #07-08 Singapore 118523 E-mail: mtl-cn@eaton.com...
Need help?
Do you have a question about the Crouse-Hinds Series and is the answer not in the manual?
Questions and answers