SORG Airon Service Record
  1. Manuals
  2. Brands
  3. SORG Manuals
  4. Wheelchair
  5. Airon
  6. Service record

SORG Airon Service Record

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Service record Airon
Airon
Airon
All individual adjustments to the wheelchair are described
below. Tools and specialist knowledge are required for these
settings. Please leave these adjustments to a qualified
2021-06-10
Service record
Service record
rehabilitation specialist.
service record Airon
Unique people, unique solutions.
Besondere Menschen, besondere Lösungen.
EN
de
1 von 36

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Airon and is the answer not in the manual?

Questions and answers

Related Manuals for SORG Airon

Summary of Contents for SORG Airon

  • Page 1 Service record Airon Airon Airon Service record Service record All individual adjustments to the wheelchair are described below. Tools and specialist knowledge are required for these settings. Please leave these adjustments to a qualified rehabilitation specialist. 2021-06-10 service record Airon Unique people, unique solutions.
  • Page 2 All content, especially texts, photographs and graphics, are protected by copyright. All rights, including copying, publishing, editing and translating, are reserved. © by SORG Rollstuhl- technik GmbH + Co. KG Benzstrasse 3-5, 68794 Oberhausen-Rheinhausen / Germany. You can find our general terms and condi- tions on our order forms and at www.sorgroll-...

  • Page 3: Table Of Contents

    3.8.3 Setting the back angle roughly 3.8.4 Fine adjustment of the back angle 26 3.8.5 Adjusting the back height 3.8.6 Replacing / removing the moulded back plate 3.9 Pads assembly 3.9.1 Nomenclature 3.9.2 Vertical adjustment 3.9.3 Horizontal adjustment 2021-06-10 service record Airon 3 von 36...

  • Page 4: The Wheelchair At A Glance

    5 seat cushions 6 protective pads 7 utensil pocket 8 frame 9 caster wheel fork 10 caster wheel 11 foot plate (continuous) 12 drive wheel 13 hand rim 14 thru axle 15 compact brake 4 von 36 service record Airon 2021-06-10...

  • Page 5: General Information

    Reversible ratchet with socket wrench inserts • Hexagon screwdriver • Phillips screwdriver • Slotted screwdriver • Plastic hammer • Side cutter • Thread locking liquid • Bicycle tube repair kit • Workbench / vice with plastic jaws 2021-06-10 service record Airon 5 von 36...

  • Page 6: Explanation Of Symbols

    Turn clockwise Front view Turn counterclockwise Rear view Steps to be performed at the same time Attach part Steps to be performed in se- quence Remove part Steps to be performed on both sides 6 von 36 service record Airon 2021-06-10...

  • Page 7: General Safety Information

    Approach obstacles slowly and overcome them carefully so that little force is exerted on the caster wheel, drive wheel and the wheelchair as a whole. 2021-06-10 service record Airon 7 von 36...

  • Page 8: Assemblies

    Hair, lint, dirt, etc. collect on the bearings of the caster wheels, making the caster wheels stiff. Remove the caster wheels at short intervals and thoroughly clean the forks, axles and sleeves. Please proceed in the same way with plastic forks. 8 von 36 service record Airon 2021-06-10...

  • Page 9: Rear Seat Height, Seat Inclination

    Then tighten the second set screw (3B) against it. An incorrectly set steering axis angle can lead to caster wheel flutter and when cornering (due to the wheel caster) to obstructive "uphill and downhill driving". 2021-06-10 service record Airon 9 von 36...
  • Page 10 Set the new caster wheel to the desired height • Replace the screws (1E) and tighten them. Be sure to check the functionality of the knee lever brake and the wheel track and readjust them if necessary. 10 von 36 service record Airon 2021-06-10...

  • Page 11: Camber

    Be sure to check the functionality of the knee lever brake as well as the wheel toe-in and the caster head angle of the caster wheels and readjust them if necessary. 2021-06-10 service record Airon 11 von 36...

  • Page 12: Track Compensation Drive Wheels

    Be sure to check the functionality of the knee lever brake as well as the wheel toe-in and the steering head angle of the caster wheels and readjust them if necessary. 3.1.8 Handbike shot If your Airon is also used with an add-on handbike, the handbike mount must be set once in advance.

  • Page 13: Extending The Wheelbase

    Be sure to check the functionality of the knee lever brake as well as the wheel toe-in and the caster head angle of the caster wheels and readjust them if necessary. 2021-06-10 service record Airon 13 von 36...

  • Page 14: Assembly Seat

    Do the same with both side panels. Reattach the side panels. Now also adjust the new position of the drive wheels (see 3.1.6.) In order to mount the drive wheels further outwards. Reinstall the drive wheels. 14 von 36 service record Airon 2021-06-10...
  • Page 15 Now also adjust the new position of the drive wheels (see 3.1.6.) In order to mount the drive wheels further outwards. Reinstall the drive wheels. Be sure to check the functionality of the knee lever brake and the wheels. 2021-06-10 service record Airon 15 von 36...

  • Page 16: Legrest Assembly

    3.3.2 Adjust the lower leg length Loosen the screws (1A) on the caster wheel adapter mount on both sides of the chair. Move the legrest to the desired position and tighten the screws (1A) again. 16 von 36 service record Airon 2021-06-10...

  • Page 17: Standard Leg Support

    Loosen the screws (2A) and (2B). Bring the footplate into the desired position and tighten it again. Angle adjustment: Loosen the (2A) screws and adjust the angle as desired and tighten the screws (2A). 2021-06-10 service record Airon 17 von 36...

  • Page 18: Side Panels Assembly

    The distance between the top of the wheel and the clothes guard should be at least 10 mm so that the clothes guard does not touch the wheel when it is under load. 18 von 36 service record Airon 2021-06-10...

  • Page 19: Armrest On The Side Part (Standard)

    In order to adjust the height of the side part (D), loosen the screws and the corresponding sleeves (B) and place the side part in the desi- red holes (E). Reattach the screws and sleeves (B) and tighten them. 2021-06-10 service record Airon 19 von 36...

  • Page 20: Brakes Assembly

    (2) First check the tire pressure of the drive wheels (required information on the tire casing). To adjust the brake, loosen both screws (C) on both sides, bring the brake body into the correspon- ding position and tighten the screws (C) again. 20 von 36 service record Airon 2021-06-10...

  • Page 21: Cable Brake

    (A) and then in- sert the screw connection into the desired hole in the spacer plate (B). Please make sure that you tighten the screws again on both sides. 2021-06-10 service record Airon 21 von 36...

  • Page 22: Anti-Tip Assembly

    (2A). To do this, remove the cone lock (2B) and move it into the hole (2C). If the cone lock (2B) is moved, the stop (3A) must also be moved into the corresponding hole (3B). 22 von 36 service record Airon 2021-06-10...

  • Page 23: Mounting The Anti-Tipper

    8. Reinstall the drive wheels. 9. Adjust the anti-tipper to the desired positi- Required tools: Allen key Size 2.5 / 4/5 Be sure to check the functionality of the knee lever brake and the wheels. 2021-06-10 service record Airon 23 von 36...

  • Page 24: Tilt Bracket Assembly

    (1B) in the drive wheel mounting tube. It is not possible to mount the tilt bar and anti- tipper on the same side of the frame at the same time. 24 von 36 service record Airon 2021-06-10...

  • Page 25: Back Assembly

    (6A) on both sides. When replacing the stabilizer bar with a new stabilizer bar or exchanging the stabilizer bar for a back bar, please proceed in the same way. 2021-06-10 service record Airon 25 von 36...

  • Page 26: Setting The Back Angle Roughly

    3.8.4 Fine adjustment of the back angle -4° 0° When the Airon is delivered, you have selected a level of activity when you placed your order. Depending on the level of activity, either the 0 ° insert (3A) or the 4 ° insert (3B) is inserted in the recess (6C).

  • Page 27: Adjusting The Back Height

    (2A) (or loosen the covering on one side). • Remove the four screws (2B), • widen the wheelchair as indicated, • screw the new bowl back (2A) with the screws (2B). 2021-06-10 service record Airon 27 von 36...

  • Page 28: Pads Assembly

    Remove the cover, • remove both screws (4A), • move the pad (4B) into the alternative holes (4C), • reinsert both screws (4A) and tighten them tightly. • Then put the covers back on. 28 von 36 service record Airon 2021-06-10...

  • Page 29: Horizontal Adjustment

    Then put the covers back on. Horizontal extension (3) Use an extension piece (spare part) for horizontal extension: • Remove the screw (3A), • insert the extension piece • and screw it together at both ends. 2021-06-10 service record Airon 29 von 36...

  • Page 30: Repairs/Maintenance/Re-Use

    Adjust the seat tilt (if available) to 90 ° • If necessary, pack removable textile parts in foil or similar • Secure the wheelchair against rolling away and soiling • Storage in a dry environment without aggressive environmental influences 30 von 36 service record Airon 2021-06-10...

  • Page 31: Lifetime

    For safety reasons and to maintain product liability, an inspection by your specialist dealer is re- quired at least once a year. This must be carried out and documented according to the checklist on the following page. 2021-06-10 service record Airon 31 von 36...
  • Page 32 Locking mechanisms (tripod springs of the push handles, quick-release axles, eccentric clamps, etc.) checked for functionality, Anti-tipper checked for tight fit and functionality. Lubrication: Moving parts and bearings are oiled Final check: Functional check of all mechanical adjustment devices carried out 32 von 36 service record Airon 2021-06-10...

  • Page 33: Technical Specifications

    Commercially available pneumatic tires, sizes 1 ", 1 3/8" or solid (same dimensions), tire infla- tion pressure usually 3-10 bar Service life 3 years with not excessive use Lifespan 5 years Normative requirements The wheelchair meets the requirements of ISO 7176-8 and the requirements against ignition 2021-06-10 service record Airon 33 von 36...

  • Page 34: Meaning Of The Labels

    5.3 Declaration of Conformity SORG Rollstuhltechnik declares that the Airon product is a class 1 device and that it complies with the relevant provisions of the EU Regulation (EU) 2017/745 on medical products. This was verified by a conformity assessment procedure in accordance with the provisions for medical products.

  • Page 35: Notes

    6 Notes 2021-06-10 service record Airon 35 von 36...
  • Page 36 Service record Airon SORG Rollstuhltechnik GmbH + Co. KG Benzstraße 3-5 68794 Oberhausen-Rheinhausen Germany Fon +49 7254 9279-0 Fax +49 7254 9279-10 info@sorgrollstuhltechnik.de www.sorgrollstuhltechnik.de company stamp...

Table of Contents