Related Manuals for Minuteman 200X
Summary of Contents for Minuteman 200X
- Page 1 200X Model: MC20001QP, CE Traction Drive MC20002QP, CE Deluxe Floor Scrubber Battery OPERATION SERVICE PARTS CARE Revised 10/03...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Page Safety Instructions Electrical Requirements Control Panel Identification Operating Instructions Squeegee Adjustments Brush Installation/Removal Base Assembly - Traction Drive 7, 8 Base Assembly - Deluxe 9, 10 Tank Assembly 11, 12 Upper Assembly Console Assembly Motor Lift Assembly - Deluxe 15, 16 Motor Lift Assembly - Traction Drive Scrubhead Assembly... -
Page 4: Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS CAUTION Operators must read and understand this manual before operating or maintaining this equipment. • Keep hands and feet clear of moving parts while machine is in operation. • All switches must be in the “OFF” position when charging batteries. •... -
Page 5: Electrical Requirements
ELECTRICAL REQUIREMENTS: This piece of equipment operates on 24 Volt DC. BATTERY REQUIREMENTS: 2 x 12V 185 Amp Hour 20 Hour Rate Deepcycle P/N 956709 2 x 12V 210 Amp Hour 20 Hour Rate Deepcycle P/N 956210 BATTERY SERVICE AND INSTALLATION: Warning: Battery acid can cause burns. -
Page 6: Control Panel Identification
1. Squeegee lift lever 2. Recovery dump hose 3. Reverse handle 4. Dashboard control panel 5. Forward handle 6. Safety bar switch 7. Solution control lever 8. Solution dump hose 9. Quick disconnect - Aux. out (Deluxe only) 10. Foot pedal (TD only) 11. -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS BEFORE STATING, FAMILIARIZE YOURSELF WITHTHE MACHINE AND ITS CONTROLS (SEE “MACHINE OVERVIEW” & CONTROL PANEL DIAGRAMS) 1. Filling: Fill the solution tank with the desired amount of water and add liquid cleaning solution to the proper dilution ratio. DO NOT USE powdered cleaning chemicals. Powders are unlikely to dissolve thoroughly, resulting in clogging the in-line solution filter. -
Page 8: Squeegee Adjustments
SQUEEGEE ADJUSTMENTS The squeegee set up is pre adjusted at the factory. Adjustments may be required to get optimum performance for different floors and conditions. Ensure that the scrubber is on a relatively flat surface. Turn on the main power switch and turn the key switch clockwise to the on position. -
Page 9: Brush Installation/Removal
BRUSH INSTALLATION - REMOVAL INSTALLATION Traction Drive 1. Raise the scrubhead to the “UP” position by depressing the pedal (A) downward as shown on Fig. 1. Deluxe Model 1. Raise the scrubhead to the “UP” position by pressing the switch “BRUSH UP” (B) switch as shown on Fig. -
Page 10: Base Assembly - Traction Drive
BASE ASSEMBLY - TRACTION DRIVE... - Page 11 TRACTION DRIVE Parts List Item Part No. Qty. Description 200102 Base 743506 Transaxle 24V 200126 Transaxle Mount 200172 Tire, Pneumatic 361233 Key 3/16 sq. x 1.50 809148 E-Ring 3/4 712318 WSR-Flat 3/4 x 1.12 x .12 712759 WSR-Flat 5/16 x 1.37 x .06 SS 712042 Bolt-WSR HH 5/16-18 x .62 711544...
-
Page 12: Base Assembly - Deluxe
BASE ASSEMBLY - DELUXE... - Page 13 DELUXE Parts List Item Part No. Qty. Description 200102 Base 743506 Transaxle 24V 200126 Transaxle Mount 200172 Tire, Pneumatic 361233 Key 3/16 sq. x 1.50 809148 E-Ring 3/4 712318 WSR-Flat 3/4 x 1.12 x .12 712759 WSR-Flat 5/16 x 1.37 x .06 SS 712042 Bolt-WSR HH 5/16-18 x .62 711544...
-
Page 14: Tank Assembly
TANK ASSEMBLY... - Page 15 Fitting Brass 90 3/8 MPT 710180 SCR-MC 1/4-20 x .75 711544 Lockwasher - Helical 1/4 711505 Washer 1/4 715285 Decal, 200X 200024 Black Vinyl Washer 712759 WSR-Flat .31 x 1.37 x .06 SS 310008 O-Ring (included in 200251) 712565 SCR-MC 1/4-20 x .625 SS...
-
Page 16: Upper Assembly
UPPER ASSEMBLY Parts List Item Part No. Qty. Description 200160 Tank Assembly 200275 Tank Assy. - Deluxe 200178 Gasket, Lid 200136 Gasket, Solution Lid 200103 Tank Lid 712120 Shoulder Bolt 1/2 x 2 710178 SCR-MC 1/4-20 x 1/2 711503 WSR-Flat #10 711125 SCR-ST-B #10 x 1/2 760286... -
Page 17: Console Assembly
CONSOLE ASSEMBLY Parts List for 200180 Item Part No. Qty. Description Item Part No. Qty. Description 200104MCH Console Machined 200240 Squeegee Lift Assy. 200134 Console Bracket Right 200241 Squeegee Lift Cable 200135 Console Bracket Left 670093 Spring, Compression 200181CTD Handle Wire, Coated 710307 SCR-MC 6-32 x 1 ST PL 200295... -
Page 18: Motor Lift Assembly - Deluxe
MOTOR LIFT - DELUXE... - Page 19 Parts List 200290 Motor Lift Assembly Item Part No. Qty. Description 200249 Base Plate Weldment - Deluxe 260036 712310 WSR-Flat .52 x .88 x .06 711527 WSR-Flat 5/8 x 1.12 x .12 762340 Oilite Bushing 1/2 260041 Oilite Flanged Bushing 1/2 200242 Lift Arm Weldment - Deluxe 711713...
-
Page 20: Motor Lift Assembly - Traction Drive
MOTOR LIFT TRACTION DRIVE Part List Item Part No. Qty. Description 200120 Base Plate Weldment 260036 712310 WSR-Flat .52 x .88 x .06 711527 WSR-Flat 5/8 x 1.12 x .12 762340 Oilite Bushing 1/2 260041 Oilite Flanged Bushing 1/2 200115 Lift Arm Weldment 711713 E-Ring 1/2... -
Page 21: Scrubhead Assembly
SCRUBHEAD ASSEMBLY Part List Item Part No. Qty. Description 200141 Motor Platform Weldment - TD 200187 Brush Shroud Weldment 200194 Pin, Brush Release 200294 Shroud Strap 210066 Retainer Bolt 200293 Shroud Skirt 260183 Nut 1/4 NPT Nylon 833621 Key, 1/4 x 1/4 x 1.00 430035 Drive Hub 500033... -
Page 24: Squeegee Assembly Complete
SCR-MC 8-32 x .50 BR 200064 Caster Wheel 3/8”-16 x 1-5/8” 200065 Castor Support Bracket 711026 Nut, Hex 8-32 Nyloc SS 200169 200X Sq Lift Weldment New 711241 SCR-Hex 3/8-16 x .75” ZP 200342 Squeegee Brkt Weldmt, 200X 711367 Nut-Wing 3/8-16 ST PL 711504... -
Page 25: Wiring Diagram
WIRING DIAGRAMS... - Page 26 200X TRACTION DRIVE AND DELUXE...
-
Page 27: Wiring Diagram - Ce
200X TRACTION DRIVE AND DELUXE... - Page 28 CE 200X TRACTION DRIVE AND DELUXE...
- Page 29 CE 200X TRACTION DRIVE AND DELUXE...
- Page 30 Minuteman International, Inc. warrants to the original purchaser/user that this product is free from defects in workmanship and materials under normal use and service for a period of three years from date of purchase. In addition, Minuteman International, Inc. will, at its option, honor labor warranty claims for the first 12 months from date of sale, provided such claims are submitted through and approved by factory authorized repair stations.