Page 1 User’s Manual iES22GF Intelligent 20 Port Managed Gigabit Ethernet Switch IEC61850 and IEEE1613 Compliant iES22GF https://is5com.com/products/ Version 1.92, Nov 2021 © 2021 iS5 Communications Inc. All rights reserved. UM-iES22GF-1.92.1-EN.docx...
Page 2 User’s Manual COPYRIGHT NOTICE © 2021 iS5 Communications Inc. All rights reserved. No part of this publication may be reproduced in any form without the prior written consent of iS5 Communications Inc. (iS5). TRADEMARKS iS5Com is a registered trademark of iS5. All other trademarks belong to their respective owners.
Page 3: Table Of Contents
iES22GF User’s Manual Table of Contents FCC Statement and Cautions ..............1 Federal Communications Commission Radio Frequency Interference Statement ........ 1 Caution: LASER ............................1 Caution: Service ............................ 1 Caution: Physical Access ........................1 1. Getting Started .................. 2 About iES22GF ........................... 2 References ..........................
Page 4 iES22GF User’s Manual 5.1.5 Authentication Method ......................22 5.1.6 Auto Logout ..........................23 5.1.7 IP Setting ..........................23 5.1.8 IPv6 Setting ..........................24 5.1.9 SNTP Configuration (only for SNTP Version) ................25 5.1.10 NTP Configuration (only for NTP Version) ................26 5.1.11 Daylight Saving Time ......................
Page 5 iES22GF User’s Manual 5.7.4 Port DSCP ..........................90 5.7.5 Port Policing ........................... 91 5.7.6 Queue Policing ........................92 5.7.7 Port Schedulers ........................92 5.7.8 Port Shaping ........................... 93 5.7.9 DSCP-Based QoS ........................96 5.7.10 DSCP Translation ........................97 5.7.11 DSCP Classification ......................... 98 5.7.12 QoS Control List ........................
Page 6 iES22GF User’s Manual Figure 3 - DIN-Rail Bracket ........................12 Figure 4 - Switch Mounted on DIN-Rail ....................12 Figure 5 - Brackets Mounted on Side of Switch ..................13 Figure 6 - Brackets Mounted on back of Switch ................... 13 Figure 7 –...
Page 7 iES22GF User’s Manual Figure 62 - STP Port Status ........................60 Figure 63 - STP Statistics ........................61 Figure 64 - MRP ........................... 62 Figure 65 - Fast Recovery ........................63 Figure 66 – Dual Port Recovery ......................65 Figure 67 - VLAN Membership Configuration ..................66 Figure 68 - VLAN Port Configuration ....................
Page 8 iES22GF User’s Manual Figure 121 - VLAN Parameters (default values or with Filter “Specific”) .......... 119 Figure 122 - IP Parameters ........................ 120 Figure 123 - ARP Parameters ......................122 Figure 124 - ICMP Parameters ......................124 Figure 125 - TCP / UDP Parameters ....................125 Figure 126 - Ethernet Type Parameters .....................
Page 9: Fcc Statement And Cautions
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by iS5 Communications Inc. could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment.
Page 10: Getting Started
The switch is made of IP-40 galvanized steel and has a wide operating temperature range from -40°C to +85°C, which is suitable for the harshest of environments without the use of fans. UM-iES22GF-1.92.1-EN.docx Page 2 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 11: References
Access Control List Assured Forwarding Address Resolution Protocol BPDU Bridge Protocol Data Unit CIST Common and Internal Spanning Tree Command Line Interface DCHP Dynamic Host Configuration Protocol Digital Diagnostic Monitoring UM-iES22GF-1.92.1-EN.docx Page 3 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 12 LLDP - Media Endpoint Discovery LLDPDU LLDP Data Unit Management Information Base Media Redundancy Protocol MSTI Multiple Spanning Tree Instances MSTP Multiple Spanning Tree Protocol Network Time Protocol Object Identifier UM-iES22GF-1.92.1-EN.docx Page 4 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 13 Source Service Access Point Secure Shel TACACS Terminal Access Controller Access Control System Topology Change Notification Transmission Control Protocol target Hardware Address Type-Length-Value TPID Tag protocol identifier Time to live UM-iES22GF-1.92.1-EN.docx Page 5 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 14 User Datagram Protocol Urgent Pointer Field Significant (an ACE value) User-based Security Model Coordinated Universal Time VACM View based Access Control Model VCXO Voltage Controlled Crystal Oscillator VLAN ID UM-iES22GF-1.92.1-EN.docx Page 6 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 15: Software Features
Redundant Power Supplies: Dual DC Inputs 9-36VDC, Dual DC Input Power Inputs 36-75VDC, or Dual Input 110-370VDC or 90-264VAC 18 Watts Power Consumption (Typ.) Present Overload Current Protection Internal Reverse Polarity Protection UM-iES22GF-1.92.1-EN.docx Page 7 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 16: Hardware Overview
Console port (RJ-45) 100/1000 Base-X SFP LED for Ethernet ports link status. LED for Ethernet ports speed status 10/100/1000Base-T(X) ports LED for SFP ports link status. 100/1000 Base-X SFP UM-iES22GF-1.92.1-EN.docx Page 8 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 17: Front Panel Led
HV: Single Input 110-370VDC or 90-264VAC There are also connections for the Failsafe Relay. The Failsafe Relay is rated 1A @ 24VDC. Connections to the Terminal block are listed in the table below. UM-iES22GF-1.92.1-EN.docx Page 9 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 18 A circuit breaker is not required for DC power supply voltages of 10-48VDC. For Dual DC power supplies, separate circuit breakers must be installed and separately identified. Equipment must be installed according to the applicable country wiring codes. UM-iES22GF-1.92.1-EN.docx Page 10 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 19: Rear Panel
Figure 1 – Rear Panel 2.5 Side Panel The components on the side of the iES10G are shown below: 1. Screw holes (4) for wall mount kit. Figure 2 – Side Panel UM-iES22GF-1.92.1-EN.docx Page 11 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 20: Hardware Installation
Figure 3 - DIN-Rail Bracket Step 2: Push the bottom of the switch toward the DIN-Rail until the bracket snaps in place. Figure 4 - Switch Mounted on DIN-Rail UM-iES22GF-1.92.1-EN.docx Page 12 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 21: Wall Mount Installation
Fix mounting brackets to back of switch using 4 screws included in the package. Figure 6 - Brackets Mounted on back of Switch Note: To avoid damage to the unit, only use the screws provided to mount the panel mount. UM-iES22GF-1.92.1-EN.docx Page 13 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 22: Connection
Table 3 – 1000 Base-T Line Pin Assignments Pin Number Assignment BI_DA+ BI_DA- BI_DB+ BI_DC+ BI_DC- BI_DB- BI_DD+ BI_DD- The iES22GF supports Auto MDI/MDI- X operation. Use a cable to connect the switch to a PC. UM-iES22GF-1.92.1-EN.docx Page 14 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 23: Sfp
LC connectors. Remember that the TX port of Switch A should be connected to the RX port of Switch B. Switch A Switch B Fiber Figure 7 – SFPs UM-iES22GF-1.92.1-EN.docx Page 15 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 24: Console Cable
— — — — 1. NC indicates not connected. 2. TXD indicates transmit data 3. RXD indicates receive data 4. GND indicates ground Figure 8 – Console Cable Connection UM-iES22GF-1.92.1-EN.docx Page 16 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 25: Redundancy Overview
Fast recovery mode can be set to connect multiple ports to one or more switches. iES22GF with fast recovery modes will provide redundant links. Only the first priority will be the active port, the other ports with different priorities will be backup ports. UM-iES22GF-1.92.1-EN.docx Page 17 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 26: Web Management
4. The login screen appears (see Figure 10 – Login Screen). Figure 10 – Login Screen 5. Enter the username and password. The default username and password are “admin”. UM-iES22GF-1.92.1-EN.docx Page 18 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 27: Figure 11 - Main Interface Or System Information Tab
Figure 11 – Main Interface or System Information tab Note: Session timeout is 10 minutes. On the left hand side, links to various settings are shown. Use them to access the different features of the switch. UM-iES22GF-1.92.1-EN.docx Page 19 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 28: Basic Setting
The offset is given in minutes east of GMT. The valid range is from -720 to 720 offset (minutes) minutes. Save Click to save changes. Click to undo any changes made locally and revert to previously saved Reset values. UM-iES22GF-1.92.1-EN.docx Page 20 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 29: Banner
The new system password. The allowed string length is 0 to 31, and only New Password ASCII characters from 32 to 126 are allowed. Confirm New Password Re-type the new password. Save Click to save changes. UM-iES22GF-1.92.1-EN.docx Page 21 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 30: Guest Password
Click to save changes. Save 5.1.5 Authentication Method Configure how a user is authenticated when he/she logs into the switch via one of the management interfaces. Figure 16 - Authentication Method Configuration UM-iES22GF-1.92.1-EN.docx Page 22 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 31: Auto Logout
Note: value 0-9999 min ; Default: 0 means 10 min 5.1.7 IP Setting You can configure IP information of the switch in this page. Figure 18 - IP Configuration UM-iES22GF-1.92.1-EN.docx Page 23 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 32: Ipv6 Setting
IPv6 settings will be used. The router Configuration may delay responding to a router solicitation for a few seconds, the total time needed to complete auto-configuration can be significantly longer. UM-iES22GF-1.92.1-EN.docx Page 24 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 33: Sntp Configuration (Only For Sntp Version)
Provide the IPv4 address of a SNTP server. Server Address Save Click to save changes Reset Click to undo any changes made locally and revert to previously saved values UM-iES22GF-1.92.1-EN.docx Page 25 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 34: Ntp Configuration (Only For Ntp Version)
Provide the IPv4 address of a NTP server. There 2 cells so a dual NTP server or active / active Server model is supported. Address Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 26 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 35: Daylight Saving Time
Date - Select the starting date. (Non-Recurring) Start Time • Year - Select the starting year. (Non-Recurring) Settings • Hours - Select the starting hour. • Minutes - Select the starting minute. UM-iES22GF-1.92.1-EN.docx Page 27 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 36: Switch Time Configuration
HTTP application layering. HTTPS encrypts and decrypts user page requests as well as the pages that are returned by the Web server. Configure HTTPS settings in the following page. Figure 24 - HTTPS Configuration UM-iES22GF-1.92.1-EN.docx Page 28 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 37: Ssh
This page allows the user to enable or disable Telnet settings. Figure 26 - Telnet Configuration Label Description Mode Indicates the selected Telnet mode. The modes include: Enabled: enable telnet. Disabled: disable Telnet. UM-iES22GF-1.92.1-EN.docx Page 29 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 38: Lldp
Disabled The switch will not send out LLDP information, and will drop LLDP information received from neighbours. Mode Enabled The switch will send out LLDP information, and will analyze LLDP information received from neighbours. UM-iES22GF-1.92.1-EN.docx Page 30 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 39: Figure 28 - Lldp Neighbor Information
Two types of counters are shown. Global Counters are counters that refer to the whole switch, while Local Counters refer to per port counters for the currently selected switch. UM-iES22GF-1.92.1-EN.docx Page 31 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 40: Figure 29 - Lldp Global Counters
Each LLDP frame can contain multiple pieces of information, known as TLV (Type TLVs Length Value). If a TLV is malformed, it will be counted and discarded. Discarded TLVs The number of well-formed TLVs but with an unknown type value Unrecognized UM-iES22GF-1.92.1-EN.docx Page 32 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 41: Modbus Tcp
Group tags: <port_table>, <vlan_table> etc. These tags identify a group of parameters, typically a table. Parameter tags: <mode>, <entry> etc. These tags identify parameters for the specific section, module UM-iES22GF-1.92.1-EN.docx Page 33 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 42: Restore
This page allows the user to update the firmware of the switch. Select the file to be load then press upload. After the software image is uploaded, a page announces that the firmware update is initiated. After about a minute, the firmware is updated and the switch restarts. UM-iES22GF-1.92.1-EN.docx Page 34 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 43: Figure 33 - Software Upload
Green/Off with a frequency of 10 Hz while the firmware update is in progress. Do not restart or power off the device at this time or the switch may fail to function afterwards. Upgrade takes 10 minutes or more based on connection bandwidth. UM-iES22GF-1.92.1-EN.docx Page 35 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 44: Dhcp Server/Relay
Boot File Name The name of Boot File (Option 67). Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 36 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 45: Dhcp Dynamic Client List
Add as Static Add dynamic entry to static table. Type The type of client (Dynamic or Static). Delete Delete selected entry. Select/Clear All Select or Clear all check boxes. UM-iES22GF-1.92.1-EN.docx Page 37 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 46: Dhcp Relay Agent
Drop: drop the package when a DHCP message containing the information is received. Save Click to save changes Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 38 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 47: Figure 38 - Dhcp Relay Statistics
Auto-refresh Check this box to refresh the page automatically. Automatic Auto-refresh refresh occurs every 3 seconds. Refresh Click to refresh the page immediately. Clear Clear all statistics. UM-iES22GF-1.92.1-EN.docx Page 39 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 48: Port Setting
Port Setting allows managing of individual ports of the switch, including traffic, power, and trunks. 5.3.1 Port Control This page shows current port configurations. Ports can also be configured here. Figure 40 – Port Configuration UM-iES22GF-1.92.1-EN.docx Page 40 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 49 Enabled: Both link up and link down power savings enabled. Refresh Click to refresh the page immediately. Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 41 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 50: Port Trunk
Figure 42 - Aggregation Group Configuration Label Description Indicates the ID of each aggregation group. Normal means no aggregation. Group ID Only one group ID is valid per port. UM-iES22GF-1.92.1-EN.docx Page 42 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 51: Figure 43 - Lacp Port Configuration
This page allows the user to inspect the current LACP port configurations, and possibly change them as well. Figure 43 – LACP Port Configuration UM-iES22GF-1.92.1-EN.docx Page 43 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 52: Figure 44 - Lacp System Status
Shows which ports are a part of this aggregation for this switch. Local Ports Click to refresh the page immediately. Refresh Auto-refresh Check to enable an automatic refresh of the page at regular Intervals. UM-iES22GF-1.92.1-EN.docx Page 44 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 53: Figure 45 - Lacp Status
The partner’s port number associated with the port. Partner Port Click to refresh the page immediately. Refresh Auto- Check to enable an automatic refresh of the page at regular intervals. refresh UM-iES22GF-1.92.1-EN.docx Page 45 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 54: Figure 46 - Lacp Statistics
Click to refresh the page immediately. Refresh Auto-refresh Check to enable an automatic refresh of the page at regular intervals. Click to clear the counters for all ports. Clear UM-iES22GF-1.92.1-EN.docx Page 46 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 55: Loop Protection
Controls whether the port is actively generating loop protection PDUs or only Tx Mode passively looking for looped PDUs. Save Click to save changes Reset Click to undo any changes made locally and revert to previously saved values UM-iES22GF-1.92.1-EN.docx Page 47 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 56: Redundancy
Dual Homing (e.g., a backbone switch). The two links work in active/backup mode, and connect each ring to the normal switches in RSTP mode. Click to apply the configurations. Save UM-iES22GF-1.92.1-EN.docx Page 48 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 57: Ichain
The second port connecting to the bridge Ring Port The list of the supported vendors is: • Moxx Vender • Advantexx • Hitshmaxx Click to apply the configurations. Save UM-iES22GF-1.92.1-EN.docx Page 49 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 58: Rstp
NOTE: Follow this rule to configure the MAX Age, Hello Time, and Forward Delay Time: 2 x (Forward Delay Time value –1) ≥ Max Age value ≥ 2 x (Hello Time value +1) UM-iES22GF-1.92.1-EN.docx Page 50 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 59: Figure 53 - Rstp Port Setting
Controls whether the bridge should enable automatic edge detection on the bridge port. This allows operEdge to be derived from whether BPDU's are received on the port or not. UM-iES22GF-1.92.1-EN.docx Page 51 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 60: Figure 54 - Rstp Bridge Status
The time that the Control Switch sends out the BPDU (Bridge Protocol Data Unit). Forward The delay used by STP Bridges to transit Root and Designated Ports to Forwarding Delay (used in STP compatible mode). UM-iES22GF-1.92.1-EN.docx Page 52 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 61: Figure 55 - Rstp Port Status
OperP2P shows the P2P status of the link to be manipulated administratively. True means P2P enabling. False means P2P disabling. Role The Role of each port is Disabled or Designated. State The State of each port is Discarding or Forwarding. UM-iES22GF-1.92.1-EN.docx Page 53 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 62: Mstp
If recovery is not enabled, ports have to be disabled and re- Port Error enabled for normal STP operation. The condition is also cleared by a system Recovery reboot. UM-iES22GF-1.92.1-EN.docx Page 54 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 63: Figure 57 - Msti Configuration
Internal Spanning Tree (CIST), which is the default spanning tree instance for MSTP, and the other in the context of each individual spanning tree context, that is, MSTI. [6] Figure 57 - MSTI Configuration UM-iES22GF-1.92.1-EN.docx Page 55 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 64: Figure 58 - Msti Configuration
Reset 5.4.5.3 MSTI Priorities This page allows the user to inspect the current MSTI bridge instance priority configurations, and possibly change them as well. Figure 58 - MSTI Configuration UM-iES22GF-1.92.1-EN.docx Page 56 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 65: Figure 59 - Stp Msti Port Configuration
Lower path cost ports are chosen as forwarding ports in favor of higher path cost ports. The range of valid values is 1 to 200000000. Priority Configures the priority for ports having identical port costs. (See above). UM-iES22GF-1.92.1-EN.docx Page 57 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 66 Transiting to forwarding state is faster for point-to-point LANs than for shared media. Save Click to save changes. Click to undo any changes made locally and revert to previously saved values. Reset UM-iES22GF-1.92.1-EN.docx Page 58 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 67: Figure 60 - Msti Port Configuration
Configures the priority for ports having identical port cost. (See above). Priority Save Click to save changes. Click to undo any changes made locally and revert to previously saved values. Reset UM-iES22GF-1.92.1-EN.docx Page 59 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 68: Figure 61 - Stp Bridges
The switch port number to which the following settings will be applied. CIST Role The current STP port role of the CIST port. The values include: AlternatePort, BackupPort, RootPort, DesignatedPort, and Non-STP. UM-iES22GF-1.92.1-EN.docx Page 60 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 69: Figure 63 - Stp Statistics
The number of illegal spanning tree BPDU’s received (and discarded) on the port. Illegal Refresh Click to refresh the page immediately. Auto- Check to enable an automatic refresh of the page at regular refresh Intervals. UM-iES22GF-1.92.1-EN.docx Page 61 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 70: Mrp
Fast Recovery is a function for port redundancy. The port has the highest recovery priority (the lowest number) will be the active port, others will be blocked (if included). UM-iES22GF-1.92.1-EN.docx Page 62 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 71: Figure 65 - Fast Recovery
The port has the highest recovery priority (the lowest number) will be the Recovery Priority active port, others will be blocked (if included). Save Click to save the configurations. UM-iES22GF-1.92.1-EN.docx Page 63 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 72: Dual Port Recovery
The disconnected port changes its status to “No Link” When link of port 1 on switch 2 returns back to be link up, the switch 1 port 1 is in “forwarding” state UM-iES22GF-1.92.1-EN.docx Page 64 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 73: Figure 66 - Dual Port Recovery
Set the maximum number of lost frames to start Dual Port Recovery mechanism (1-500 Retry retries default 3 )Note: Test Max Retry should be the same on both sides. Apply Click Apply to activate the configurations. UM-iES22GF-1.92.1-EN.docx Page 65 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 74: Vlan
VLAN name. VLAN name can be edited for the existing VLAN entries or it can be added to the new entries. UM-iES22GF-1.92.1-EN.docx Page 66 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 75: Ports Configuration
Click to undo any changes made locally and revert to previously saved values. 5.5.2 Ports Configuration This page is used for configuring the switch port VLAN. Figure 68 - VLAN Port Configuration UM-iES22GF-1.92.1-EN.docx Page 67 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 76 Tag_all: all VLANs are tagged. Untag_all: all VLANs are untagged. 5.5.2.1 Port Types Below is a detailed description of each port type, including Unaware, C-port, S-port, and S- custom-port. UM-iES22GF-1.92.1-EN.docx Page 68 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 77 1. If the tagged frame contains a TPID of S-port 0x8100, it will be forwarded. 2. If the TPID of tagged frame is not 0x88A8 (ex. 0x8100), it will be discarded. UM-iES22GF-1.92.1-EN.docx Page 69 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 78 0x8100, it will be forwarded. by the user via Ethertype for Custom If the TPID of tagged frame is not 0x88A8 S-ports. (ex. 0x8100), it will be discarded. UM-iES22GF-1.92.1-EN.docx Page 70 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 80: Figure 69 - Vlan Membership Configuration
Port 7 is VLAN Access mode = Untagged 20 Port 8 is VLAN Access mode = Untagged 10 Below are the switch settings. Figure 69 - VLAN Membership Configuration Figure 70 - VLAN Port Configuration UM-iES22GF-1.92.1-EN.docx Page 72 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 81: Figure 71 - Vlan Membership Configuration
Port 1 = VLAN 1Qtrunk mode = tagged 10, 20 Port 2 = VLAN 1Qtrunk mode = tagged 10, 20 Below are the switch settings. Figure 71 - VLAN Membership Configuration Figure 72 - VLAN Port Configuration UM-iES22GF-1.92.1-EN.docx Page 73 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 82: Figure 73 - Vlan Membership Configuration
Figure 74 - VLAN Port Configuration VLAN QinQ Mode: VLAN QinQ mode is usually adopted when there are unknown VLANs, as shown in the figure below VLAN “X” = Unknown VLAN UM-iES22GF-1.92.1-EN.docx Page 74 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 83: Figure 75 - Vlan Membership Configuration
VLAN ID Settings When setting the management VLAN, only the same VLAN ID port can be used to control the switch. iES22GF VLAN Settings: Figure 77 – IP Configuration UM-iES22GF-1.92.1-EN.docx Page 75 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 84: Private Vlan
Click to undo any changes made locally and revert to previously saved values. Check this box to refresh the page automatically. Automatic refresh occurs Auto-refresh every 3 seconds. Click to refresh the page immediately Refresh UM-iES22GF-1.92.1-EN.docx Page 76 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 85: Figure 79 - Port Isolation Configuration
Check this box to refresh the page automatically. Automatic refresh occurs every Auto-refresh 3 seconds. Save Click to save changes. Click to undo any changes made locally and revert to previously saved values. Reset UM-iES22GF-1.92.1-EN.docx Page 77 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 86: Snmp
Indicates the SNMPv3 engine ID. The string must contain an even number between 10 and 64 hexadecimal digits, but all-zeros and all-'F's are not allowed. Change of the Engine ID will clear all original local users. UM-iES22GF-1.92.1-EN.docx Page 78 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 87: Figure 81 - Snmp Trap Configuration
16-bit groups of contiguous zeros; but it can appear only once. It can also represent a legally valid IPv4 address. For example, '::192.1.2.34'. UM-iES22GF-1.92.1-EN.docx Page 79 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 88: Snmp Community Configurations
Click to undo any changes made locally and revert to previously saved values. Reset 5.6.2 SNMP Community Configurations This page allows the user to configure SNMPv3 community table. The entry index key is Community. Figure 82 – SNMPv3 Community Configuration UM-iES22GF-1.92.1-EN.docx Page 80 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 89: Snmp User Configurations
A string identifying the user name that this entry should belong to. The allowed string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126. UM-iES22GF-1.92.1-EN.docx Page 81 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 90 AES: An optional flag to indicate that this user uses AES authentication protocol. Privacy A string identifying the privacy pass phrase. The allowed string length is Password 8 to 32 and only ASCII characters from 33 to 126 are allowed. UM-iES22GF-1.92.1-EN.docx Page 82 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 91: Snmp Group Configurations
5.6.5 SNMP View Configurations This page allows the user to configure SNMPv3 view table. The entry index keys are View Name and OID Subtree. Figure 85 – SNMPv3 View Configuration UM-iES22GF-1.92.1-EN.docx Page 83 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 92: Snmp Access Configurations
Indicates the security model that this entry should belong to. Possible security models include: any: Accepted any security model (v1|v2c|usm). v1: Reserved for SNMPv1. v2c: Reserved for SNMPv2c. usm: User-based Security Model (USM). UM-iES22GF-1.92.1-EN.docx Page 84 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 93 Add New Entry Click to add a new access configuration. Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 85 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 94: Traffic Prioritization
(ACLs), Differentiated Services Code Point (DSCP), Class of Service (CoS), and other factors. • Marking —used on traffic to convey specific information to a downstream device in the network, or UM-iES22GF-1.92.1-EN.docx Page 86 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 95: Figure 88 - Qos Ingress Port Classification
The classified QoS class can be overruled by a QCL entry. Note: if the default QoS class has been dynamically changed, then the actual default QoS class is shown in parentheses after the configured default QoS class. UM-iES22GF-1.92.1-EN.docx Page 87 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 96: Port Tag Remarking
Click to undo any changes made locally and revert to previously saved values. 5.7.3 Port Tag Remarking This page provides an overview of QoS Egress Port Tag Remarking for all switch ports. UM-iES22GF-1.92.1-EN.docx Page 88 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 97: Figure 89 - Qos Egress Port Tag Remarking
Mode Shows the tag remarking mode for this port: Classified: use classified PCP/DEI values. Default: use default PCP/DEI values. Mapped: use mapped versions of QoS class and DP level. UM-iES22GF-1.92.1-EN.docx Page 89 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 98: Port Dscp
Remap: DSCP from the analyzer is remapped and the frame is remarked with remapped DSCP value. Click to save changes. Save Click to undo any changes made locally and revert to previously saved values. Reset UM-iES22GF-1.92.1-EN.docx Page 90 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 99: Port Policing
If flow control is enabled and the port is in flow control mode, then pause frames are Flow Control sent instead of discarding frames. Click to save changes. Save Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 91 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 100: Queue Policing
Click the port number to configure the schedulers. Details for configuration can be found in the QoS Egress Port Scheduler and Shapers section. Shows the scheduling mode for this port. Mode Shows the weight for this queue and port. Weight UM-iES22GF-1.92.1-EN.docx Page 92 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 101: Port Shaping
This is accessed by clicking specific port on the Port Scheduler or Shaping screen (Port 1 shown). 5.7.8.1.1 Strict Priority In the Scheduler Mode, from the drop-down list, select Strict Priority. Figure 95 - QoS Ingress Port Scheduler and Shapers Port 1- Strict Priority UM-iES22GF-1.92.1-EN.docx Page 93 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 102: Figure 96 - Qos Egress Port Scheduler And Shapers Port 1 - Scheduler Mode Weighted
Click to undo any changes made locally and return to the previous page. Cancel 5.7.8.1.2 Weighted In the Scheduler Mode, from the drop-down list, select Weighted. Figure 96 - QoS Egress Port Scheduler and Shapers Port 1 – Scheduler Mode Weighted UM-iES22GF-1.92.1-EN.docx Page 94 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 103 Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. Cancel Click to undo any changes made locally and return to the previous page. UM-iES22GF-1.92.1-EN.docx Page 95 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 104: Dscp-Based Qos
Click to save changes. frames and a DP level of 1 corresponds to 'Discard Eligible' (Yellow) frames Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 96 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 105: Dscp Translation
DSCP value ranges form 0 to 63. Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 97 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 106: Dscp Classification
Actual Drop Precedence Level. DSCP Select the classified DSCP value (0-63) Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 98 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 107: Qos Control List
DMAC Type : Destination MAC type, can be unicast (UC), multicast (M C), broadcast (BC) or Any Frame Type can be values such as Any, Ethernet, LLC, SNAP, IPv4, IPv6 UM-iES22GF-1.92.1-EN.docx Page 99 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 108 Valid Drop Precedence Level value can be (0-3) or Default. Action Valid DSCP value can be (0-63, BE, CS1-CS7, EF or AF11-AF43) or Parameters Default. Default means that the default classified value is not modified by this QCE. UM-iES22GF-1.92.1-EN.docx Page 100 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 109: Qos Statistics
The number of received and transmitted packets per queue. Refresh Click to refresh the page immediately. Clear Clear all statistics counters. Auto-refresh Check to enable an automatic refresh of the page at regular intervals. UM-iES22GF-1.92.1-EN.docx Page 101 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 110: Figure 102 - Detailed Port Statistics Port 7
On Figure 101 QoS Statistics, go to Port 7 (identified with a red rectangle) and click it. The following page appears. Figure 102 - Detailed Port Statistics Port 7 UM-iES22GF-1.92.1-EN.docx Page 102 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 111: Qcl Status
Yes, otherwise it is always No. Please note that conflict can be resolved by releasing the hardware resources required to add the QCL entry by pressing Resolve Conflict button. UM-iES22GF-1.92.1-EN.docx Page 103 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 112 Conflict: Show conflict entries. Clear Clear all statistics counters. Auto- Check this box to refresh the page automatically. Automatic refresh occurs every 3 refresh seconds. Refresh Click to refresh the page. UM-iES22GF-1.92.1-EN.docx Page 104 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 113: Multicast
Fast Leave Check to enable fast leave on the port Save Click to save changes. Reset Click to undo any changes made locally and revert to previously saved values. UM-iES22GF-1.92.1-EN.docx Page 105 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 114: Igmp Snooping Vlan Configurations
Click to add a new entry into the table. IGMP VLAN Click to save changes. Save Click to undo any changes made locally and revert to previously saved values. Reset UM-iES22GF-1.92.1-EN.docx Page 106 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 115: Igmp Snooping Status
Check to enable an automatic refresh of the page at regular intervals. Router Port Port number on the switch. Router Port Status Indicates whether a specific port is a router port or not UM-iES22GF-1.92.1-EN.docx Page 107 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 116: Igmp Snooping Group Information
Refreshes the displayed table starting from the input fields. |<< Updates the table, starting with the first entry in the IGMP Group Table. >> Updates the table, starting with the entry after the last entry currently displayed. UM-iES22GF-1.92.1-EN.docx Page 108 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 117: Security
Additionally, the bound device also benefits from a collection of active network traffic protection and maintenance tools — Alive Check, Stream Check, and DoS/DDoS auto-prevention. This page provides Device Binding related configuration. Figure 109 - Device Binding UM-iES22GF-1.92.1-EN.docx Page 109 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 118 Indicates the DDOS Prevention status. Possible options are: DDOS ---: Disable. Prevention Analysing: Analyse the packet throughput for initialization. Status Running: Function ready. Attacked: DDOS attack happened. Click to save changes. Save UM-iES22GF-1.92.1-EN.docx Page 110 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 119: Figure 110 - Alias Ip Address
Link Change: Link down the port, and link up once. Action Only Log it Shunt Down the Port: Shut down the port(No Link), and log the event. Only Log it: Just log the event. UM-iES22GF-1.92.1-EN.docx Page 111 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 120: Figure 112 - Ddos Prevention
In this case, Number please insert the same number. If packet type is UDP (or TCP), please choose the socket direction (Destination / Filter Source). UM-iES22GF-1.92.1-EN.docx Page 112 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 121: Figure 113 - Device Description
Device Type Phone, Access Point, PC, PLC, and Network Video Recorder Indicates location information of the device. The information can be used for Location Address Google Mapping. Description Device descriptions UM-iES22GF-1.92.1-EN.docx Page 113 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 122: Figure 114 - Steam Check
Indicates the action to take when the stream gets low. Possible actions are: Action ---: no action Log it: simply logs the event Indicates the Stream Check status. Possible statuses are: ---: disables Stream Check Status Normal: Stream Check is enabled UM-iES22GF-1.92.1-EN.docx Page 114 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 123: Acl
Specifies the shutdown operation of this port. The allowed values are: Enabled: if a frame is received on the port, the port will be disabled. Shutdown Disabled: port shut down is disabled. The default value is Disabled. UM-iES22GF-1.92.1-EN.docx Page 115 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 124: Figure 116 - Acl Rate Limiter Configuration
Specify the rate unit. The allowed values are: pps: packets per second. Unit kbps: Kbits per second. Click to save changes. Save Click to undo any changes made locally and revert to previously saved values. Reset UM-iES22GF-1.92.1-EN.docx Page 116 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 125: Figure 117 - Acl Control List Configuration
First select the Ingress Port for the ACE, and then select the frame type. Different parameter options are displayed depending on the frame type selected. A frame that hits this ACE matches the configuration that is defined here. UM-iES22GF-1.92.1-EN.docx Page 117 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 126: Figure 119 - Ace Configuration
Disabled indicates that the port Port redirect operation is disabled and the specific port number of 'Port Redirect' can't be set Redirect when action is permitted. UM-iES22GF-1.92.1-EN.docx Page 118 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 127: Figure 120 - Mac Parameters
Specify whether frames can hit the action according to the 802.1Q tagged. The allowed values are: Any: Any value is allowed ("don't-care"). 802.1Q Enabled: Tagged frame only. Tagged Disabled: Untagged frame only. The default value is Any. UM-iES22GF-1.92.1-EN.docx Page 119 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 128: Figure 122 - Ip Parameters
Any means that no tag priority is specified (tag priority is "don't-care"). 5.9.3.3.3 IP Parameters Figure 122 - IP Parameters The IP parameters can be configured when Frame Type of IPv4 is selected (see Figure 119 - ACE Configuration). UM-iES22GF-1.92.1-EN.docx Page 120 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 129 IP mask in the SIP Address and SIP Mask fields that appear. When Host or Network is selected for the source IP filter, you can enter a specific SIP address in dotted decimal notation. Address UM-iES22GF-1.92.1-EN.docx Page 121 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 130: Figure 123 - Arp Parameters
DIP M ask in dotted decimal notation. 5.9.3.3.4 ARP Parameters The ARP parameters can be configured when Frame Type of ARP is selected (see below). Figure 123 - ARP Parameters UM-iES22GF-1.92.1-EN.docx Page 122 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 131 0: ARP frames where SHA is not equal to the SMAC address MAC Match 1: ARP frames where SHA is equal to the SMAC address Any: any value is allowed ("don't-care "). UM-iES22GF-1.92.1-EN.docx Page 123 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 132: Figure 124 - Icmp Parameters
5.9.3.3.5 ICMP Parameters ICMP Parameters can be configured when: • Frame Type is IPv4 • IP Protocol Filter is Internet Control Message Protocol (ICMP) Figure 124 - ICMP Parameters UM-iES22GF-1.92.1-EN.docx Page 124 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 133: Figure 125 - Tcp / Udp Parameters
Figure 125 - TCP / UDP Parameters TCP Parameters can be configured when IP Protocol Filter is set to TCP. Similarly, UDP Parameters can be configured when IP Protocol Filter is set to UDP. UM-iES22GF-1.92.1-EN.docx Page 125 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 134 0: TCP frames where the FIN field is set must not be able to match this entry. TCP FIN 1: TCP frames where the FIN field is set must be able to match this entry. Any: any value is allowed ("don't-care "). UM-iES22GF-1.92.1-EN.docx Page 126 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 135: Figure 126 - Ethernet Type Parameters
When Specific is selected for the EtherType filter, you can enter a specific EtherType Ethernet value. The allowed range is 0x600 to 0xFFFF but excluding 0x800(IPv4), 0x806(ARP) Type Value and 0x86DD(IPv6). A frame that hits this ACE matches this EtherType value. UM-iES22GF-1.92.1-EN.docx Page 127 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 136: Figure 127 - Acl Status
The counter indicates the number of times the ACE was hit by a frame. Indicates the hardware status of the specific ACE. The specific ACE is not applied to the Conflict hardware due to hardware limitations. UM-iES22GF-1.92.1-EN.docx Page 128 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 137: Aaa
If a reply is not received within the subinterval, the request is transmitted again. This algorithm causes the RADIUS server to be queried up to 3 times before it is considered to be dead. UM-iES22GF-1.92.1-EN.docx Page 129 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 138: Figure 129 - Radius Authentication Server Configuration
The RADIUS Accounting Server number for which the configuration below applies. Enabled Enable the RADIUS Accounting Server by checking this box The IP address of the RADIUS Authentication Server. IP address is expressed in dotted IP Address decimal notation. UM-iES22GF-1.92.1-EN.docx Page 130 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 139: Figure 131 - Tacacs+ Authentication Server Configuration
5.9.4.2 RADIUS Overview This page provides an overview of the status of the RADIUS servers configurable on the authentication configuration page. Figure 132 - Radius Authentication Server Status Configuration UM-iES22GF-1.92.1-EN.docx Page 131 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 140: Figure 133 - Radius Accounting Server Status Configuration
The server has temporarily been disabled, but will get re-enabled when the dead-time expires. The number of seconds left before this occurs is displayed in parentheses. This state is only reachable when more than one server is enabled. UM-iES22GF-1.92.1-EN.docx Page 132 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 141: Figure 134 - Radius Authentication Statistics For Server #1
(valid or invalid) received from the server. number of malformed RADIUS Access- Malformed radiusAuthClientExt Response packets received from the server. Access MalformedAccessRe Malformed packets include packets with an invalid Responses sponses length. authenticators Message UM-iES22GF-1.92.1-EN.docx Page 133 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 142 A send to a different server is counted as a Request as well as a timeout. Other info: This section contains information about the state of the server and the latest round-trip time. UM-iES22GF-1.92.1-EN.docx Page 134 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 143: Figure 135 - Radius Accounting Statistics For Server #1
The number of malformed RADIUS packets received from the server. Malformed Malformed radiusAccClientExtMalformedResponses packets include packets with Responses an invalid length. Bad authenticators or unknown types are not included as UM-iES22GF-1.92.1-EN.docx Page 135 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 144 Dead (X seconds left): Accounting attempts were made to this server, but it did not reply within the configured timeout. The server has temporarily been disabled, but will get re-enabled UM-iES22GF-1.92.1-EN.docx Page 136 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 145 3 seconds. Click to refresh the page immediately. Refresh Clears the counters for the selected server. The "Pending Requests" counter Clear will not be cleared by this operation. UM-iES22GF-1.92.1-EN.docx Page 137 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 146: Nas (802.1X)
(because the X seconds have not expired), the same server will be contacted when the next back-end authentication server requests from the switch. This scenario will loop forever. Therefore, the server timeout should be smaller than the supplicant's EAPOL Start frame retransmission rate. UM-iES22GF-1.92.1-EN.docx Page 138 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 147: Figure 136 - Network Access Server Configuration
RADIUS user can be used by anyone, and only the MD5-Challenge method is supported. 802.1x and MAC-Based authentication configurations consist of two sections: system- and port wide. Figure 136 - Network Access Server Configuration UM-iES22GF-1.92.1-EN.docx Page 139 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 148 The switch will ignore new frames coming from the client during the hold time. The hold time can be set to a number between 10 and 1000000 seconds. UM-iES22GF-1.92.1-EN.docx Page 140 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 149: Figure 137 - Network Access Server Port Configuration
Note: Suppose two backend servers are enabled and that the server timeout is configured to X seconds (using the AAA configuration page), and suppose that the first server in the list is currently down (but not considered dead). Now, if the UM-iES22GF-1.92.1-EN.docx Page 141 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 150 Reinitialize: forces a reinitialization of the clients on the port and hence a reauthentication immediately. The clients will transfer to the unauthorized state while the reauthentication is in progress. UM-iES22GF-1.92.1-EN.docx Page 142 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 151: Figure 138 - Network Access Server Switch Status
Note that Port counters are shown only for ports with Authorized port state such Port 20 (refer to Figure 138- Network Access Server Switch Status). Port 1 does not show Port counters. UM-iES22GF-1.92.1-EN.docx Page 143 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 152: Figure 139 - Nat Statistics Admin State Force Authorized
Click to refresh the page immediately. This button is available in the following modes: • Force Authorized • Force Unauthorized Clear • 802.1X Click to clear the counters for the selected port UM-iES22GF-1.92.1-EN.docx Page 144 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 153: Figure 140 - Eapol Counters Admin State Force Authorized
The number of valid EAPOL Request dot1xAuthEapolReqFrames Requests frames (other than Request Identity frames) that have been transmitted by the switch. UM-iES22GF-1.92.1-EN.docx Page 145 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 154: Figure 141 - Nat Statistics Admin Mac-Based Auth
"Last Client" will not be cleared, however. This button is available in the following modes: Clear This • MAC-based Auth.X Click to clear only the currently selected client's counters. UM-iES22GF-1.92.1-EN.docx Page 146 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 155 Counts all the backend server packets sent from the switch towards the backend server for a given port (left-most table) or client (right-most table). Possible retransmissions are not counted. UM-iES22GF-1.92.1-EN.docx Page 147 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 156: Figure 142 - Last Supplicant/ Client Info Admin State Mac-Based Auth
802.1X-based: The user name (supplicant identity) carried in the Identity most recently received Response Identity EAPOL frame. MAC-based: Not applicable (as shown on Figure 142). Figure 143 - Last Supplicant/ Client Info Admin State 802.1X-based. UM-iES22GF-1.92.1-EN.docx Page 148 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 157: Figure 144 - Selected Counters / Attached Clients
Hold Time seconds. Shows the date and time of the last authentication of the client (successful as Last Authentication well as unsuccessful). UM-iES22GF-1.92.1-EN.docx Page 149 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 158: Warning
UDP is a connectionless protocol and it does Mode not provide acknowledgments. The syslog packet will always be sent even if the syslog server does not exist. Possible modes are: UM-iES22GF-1.92.1-EN.docx Page 150 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 159: Figure 147 - Smtp Settings
Username: the authentication username Authentication Password: the authentication password Confirm Password: re-enter password Recipient E-mail The recipient’s e-mail address, allows a total number of six recipients. Address Save Click to save changes UM-iES22GF-1.92.1-EN.docx Page 151 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 160: Figure 148 - System Warning - Event Selection
Please note that the checkboxes cannot be added when SYSLOG is disabled. Label Description Alerts when the system is restarted. System Start Alerts when power is up or down. Power Status Alerts when SNMP authentication fails. SNMP Authentication Failure UM-iES22GF-1.92.1-EN.docx Page 152 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 161: Monitor And Diagnostic
MAC table here. Figure 149 - MAC Address Table Configuration 5.11.1.1.1 Aging Configuration By default, dynamic entries are removed from the MAC after 300 seconds. This removal is called UM-iES22GF-1.92.1-EN.docx Page 153 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 162 MAC Table. The first displayed will be the one with the lowest VLAN ID and the lowest MAC address found in the MAC Table. The Start from M AC address and VLAN fields allow the user to select the starting point in the MAC UM-iES22GF-1.92.1-EN.docx Page 154 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 163: Figure 150 - Mac Address Table
Updates the table starting from the first entry in the MAC Table, i.e. the entry with the lowest VLAN ID and MAC address. >> Updates the table, starting with the entry after the last entry currently displayed. UM-iES22GF-1.92.1-EN.docx Page 155 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 164: Port Statistic
Check to enable an automatic refresh of the page. Automatic refresh occurs every 3 Auto-refresh seconds at regular intervals. Click to refresh the page immediately. Refresh Clears the counters for all ports. Clear UM-iES22GF-1.92.1-EN.docx Page 156 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 165: Figure 152 - Detailed Post Statistics
Tx Late / Exc. Coll. 1. Short frames are frames smaller than 64 bytes. 2. Long frames are frames longer than the maximum frame length configured for this port. UM-iES22GF-1.92.1-EN.docx Page 157 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 166: Port Monitoring
Note: For a given port, a frame is only transmitted once. It is therefore not possible to mirror port Tx frames. Because of this, the Mode for the selected mirror port (which in the Figure above is Port 1) is limited to Disabled or Rx only. UM-iES22GF-1.92.1-EN.docx Page 158 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 167: System Log Information
10 and 100 Mbps ports will be linked down while running VeriPHY. Therefore, running VeriPHY on a 10 or 100 Mbps management port will cause the switch to stop responding until VeriPHY is complete. This page allows the user to perform VeriPHY cable diagnostics. UM-iES22GF-1.92.1-EN.docx Page 159 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 168: Figure 155 - Veriphy Cable Diagnostics
• Cross C - Abnormal cross-pair coupling with pair C • Cross D - Abnormal cross-pair coupling with pair D Length: the length (in meters) of the cable pair UM-iES22GF-1.92.1-EN.docx Page 160 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 169: Sfp Monitor
This page allows the user to issue ICMP packets to troubleshoot IP connectivity issues. Figure 157 - ICMP Ping After you press Start, five ICMP packets will be transmitted, and the sequence number and UM-iES22GF-1.92.1-EN.docx Page 161 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 170: Ping6
You can reset the configuration of the stack switch on this page. The IP configuration and/or User/Password ar e retained only if the respective boxes are checked when the switch is restored to factory defaults. UM-iES22GF-1.92.1-EN.docx Page 162 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 171: System Reboot
You can reset the stack switch on this page. After reset, the system will boot normally as if you have powered on the devices. Figure 160 - System Reboot - Restart Device Label Description Click to reboot device. Click to return to the System Information page without rebooting. UM-iES22GF-1.92.1-EN.docx Page 163 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 172: Cli Management
115200 for Baud rate, 8 for Data bits, None for Parity, 1 bit for Stop and none for Flow control. Then, click OK. Figure 162 – Tera Term VT, Serial port setup UM-iES22GF-1.92.1-EN.docx Page 164 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 173: Figure 163 - Ies22Gf Command Line Interface - Tera Term Vt
4. Press “Enter” for the Console login screen to appear. Use the keyboard to enter the Console Username and Password which is same as for Web management (admin for both), then press “Enter”. Figure 163 - iES22GF Command Line Interface - Tera Term VT UM-iES22GF-1.92.1-EN.docx Page 165 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 174: Cli Management By Telnet
“Enter”. This is the same as the Web Browser password. The default Username is “admin” and the default Password is “admin”. Figure 165 - iES22GF Command Line Interface - Telnet UM-iES22GF-1.92.1-EN.docx Page 166 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 175: Command Groups
Type '<command> ?' to get help on a command, e.g. 'port mode ?'. Commands may be abbreviated, e.g. 'por co' instead of 'port configuration'. > Figure 166 - Command Groups Printout UM-iES22GF-1.92.1-EN.docx Page 167 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 176 <ping_interval>)] IP IPv6 SNTP Server1 Add [<ipv6_addr>] IP IPv6 SNTP Server2 Add [<ipv6_addr>] IP IPv6 SNTP Server1 Delete IP IPv6 SNTP Server2 Delete 6.1.3.3 Port >port ? Available Commands: UM-iES22GF-1.92.1-EN.docx Page 168 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 177 VLAN Status [<port_list>] [combined|static|nas|mstp|all|conflicts] > 6.1.3.6 Private VLAN (PVLAN) >pvlan ? Available Commands: PVLAN Configuration [<port_list>] PVLAN Add <pvlan_id> [<port_list>] PVLAN Delete <pvlan_id> PVLAN Lookup [<pvlan_id>] PVLAN Isolate [<port_list>] [enable|disable] UM-iES22GF-1.92.1-EN.docx Page 169 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 178 Security/Switch> 6.1.3.7.1.2 Security Switch Privilege Security/Switch>Privilege ? Available Commands: Security Switch Privilege Level Configuration Security Switch Privilege Level Group <group_name> [<cro>] [<crw>] [<sro>] [<srw>] Security Switch Privilege Level Current UM-iES22GF-1.92.1-EN.docx Page 170 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 179 Security Switch RMON History Add <history_id> <data_source> [<interval>] [<buckets>] Security Switch RMON History Delete <history_id> Security Switch RMON History Lookup [<history_id>] Security Switch RMON Alarm Add <alarm_id> <interval> <alarm_variable> [absolute|delta] <rising_threshold> <rising_event_index> <falling_threshold> UM-iES22GF-1.92.1-EN.docx Page 171 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 180 Security Network NAS ReauthPeriod [<reauth_period>] Security Network NAS EapolTimeout [<eapol_timeout>] Security Network NAS Agetime [<age_time>] Security Network NAS Holdtime [<hold_time>] Security Network NAS Authenticate [<port_list>] [now] Security Network NAS Statistics [<port_list>] [clear|eapol|radius] Security/Network> UM-iES22GF-1.92.1-EN.docx Page 172 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 181 Security AAA RADIUS [<server_index>] [enable|disable] [<ip_addr_string>] [<secret>] [<server_port>] Security AAA ACCT_RADIUS [<server_index>] [enable|disable] [<ip_addr_string>] [<secret>] [<server_port>] Security AAA TACACS+ [<server_index>] [enable|disable] [<ip_addr_string>] [<secret>] [<server_port>] Security AAA Statistics [<server_index>] Security> 6.1.3.8 STP >stp ? Available Commands: UM-iES22GF-1.92.1-EN.docx Page 173 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 182 SNMP Community Add <community> [<ip_addr>] [<ip_mask>] SNMP Community Delete <index> SNMP Community Lookup [<index>] SNMP User Add <engineid> <user_name> [MD5|SHA] [<auth_password>] [DES] [<priv_password>] SNMP User Delete <index> SNMP User Changekey <engineid> <user_name> <auth_password> [<priv_password>] UM-iES22GF-1.92.1-EN.docx Page 174 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 183 QoS Port Classification DPL [<port_list>] [<dpl>] QoS Port Classification PCP [<port_list>] [<pcp>] QoS Port Classification DEI [<port_list>] [<dei>] QoS Port Classification Tag [<port_list>] [enable|disable] QoS Port Classification Map [<port_list>] [<pcp_list>] [<dei_list>] [<class>] [<dpl>] UM-iES22GF-1.92.1-EN.docx Page 175 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 184 QoS QCL Refresh > 6.1.3.14 Mirror >mirror ? Available Commands: Mirror Configuration [<port_list>] Mirror Port [<port>|disable] Mirror Mode [<port_cpu_list>] [enable|disable|rx|tx] > 6.1.3.15 Config >config ? Available Commands: Config Save <ip_server> <file_name> UM-iES22GF-1.92.1-EN.docx Page 176 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 185 6.1.3.20 Event >event ? Available Commands: Event Configuration Event Syslog SystemStart [enable|disable] Event Syslog PowerStatus [enable|disable] Event Syslog SnmpAuthenticationFailure [enable|disable] Event Syslog RingTopologyChange [enable|disable] Event Syslog Port [<port_list>] [disable|linkup|linkdown|both] UM-iES22GF-1.92.1-EN.docx Page 177 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 186 Configuration iBridge Mode [enable|disable] iBridge 1stRingPort [<port>] iBridge 2ndRingPort [<port>] iBridge Vender [moxx|advantexx|hirschmaxx] 6.1.3.25 >rcs ? Available Commands: RCS Mode [enable|disable] RCS Add [<ip_addr>] [<port_list>] [web_on|web_off] [telnet_on|telnet_off] [snmp_on|snmp_off] UM-iES22GF-1.92.1-EN.docx Page 178 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 187 DeviceBinding Port Stream Status [<port_list>] DeviceBinding Port Addr [<port_list>] [<ip_addr>] [<mac_addr>] DeviceBinding Port Alias [<port_list>] [<ip_addr>] DeviceBinding Port DeviceType [<port_list>] [unknown|ip_cam|ip_phone|ap|pc|plc|nvr] DeviceBinding Port Location [<port_list>] [<device_location>] DeviceBinding Port Description [<port_list>] [<device_description>] UM-iES22GF-1.92.1-EN.docx Page 179 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 188 RSTP Port P2P [<stp_port_list>] [enable|disable|auto] RSTP Port Cost [<stp_port_list>] [<path_cost>] RSTP Port Priority [<stp_port_list>] [<priority>] 6.1.3.33 Auto-Logout >auto-logout ? Available Commands: Auto-Logout CLI [<timer>] Auto-Logout Web [<timer>] 6.1.3.34 Show >show ? Available Commands: UM-iES22GF-1.92.1-EN.docx Page 180 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...
Page 190: Appendix A: Ies22Gf Modbus Information
Port :1~VTSS_PORTS Value :0x0000 10M‐Half 0x0001 10M‐Full 0x0002 100M‐Half 0x0003 100M‐Full 0x0004 1G‐Half 0x0005 1G‐Full 0xffff NoPort 4608 PortFlowCtrl : Port :1~VTSS_PORTS Value :0x0000 Off 0x0001 On 0xffff NoPort UM-iES22GF-1.92.1-EN.docx Page 182 © 2021 IS5 COMMUNICATIONS INC. ALL RIGHTS RESERVED...

IS5 COMMUNICATIONS IEC61850 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for IS5 COMMUNICATIONS IEC61850

Summary of Contents for IS5 COMMUNICATIONS IEC61850

Table of Contents